Question about 1999 Chevrolet Silverado 1500

1 Answer

Installing a new fuel pump lock ring will not seat unless I remove the oring then it seats easily, also the tab on the module does not line up with the slot on the tank did we get the wrong pump... 1999 chev silverado

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 84 Answers

Sounds like you may have got a pump for the same vehicle but different engine size. However on the oring you need to lube it sometimes to get it to seat. At times I have used the old oring instead of the new just because it wont seat. Check your engine size and the application for the pump you bought see if its the same. Sometime they come with an universal adapter you have to manually splice into the harness.

Posted on Oct 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel pump driver module




  1. Open Gas Cap. Ensure no open flames or Heated objects are nearby. Relieve the by loosening/disconnecting the fuel lines. Make sure you have a container to catch the fuel. Disconnect the battery Negative/ground cable. Lift the Left Hand rear seat cushion. It is necessary to lift the access cover on the floor scuff plate to access one of the pin-type retainers. Pull the the carpet aside. Remove the screws and the fuel pump module access cover. Disconnect the Fuel pump electrical wire connectors. Disconnect the fuel and vapor lines from the Fuel Tank. This has a quick release coupling.Rotate the lock ring counterclockwise and remove. Handle the fuel pump module must be handled carefully to avoid damage to the float arm and filter. Some fuel will remain in the fuel pump module after draining the Fuel Tank. Carefully drain the fuel pump module into a suitable container. Prior to completely removing the fuel pump, position it aside and using a suitable fuel recovery system, drain the Fuel Tank..



To release the bottom-mounted fuel pump module, reach into the fuel pump module opening and squeeze the retainer tabs or the pump module housing and pull upward. Remove the fuel pump module.



Be careful that no foreign material fall into the tank. Remove and discard the fuel pump module O-ring seal, making sure the mounting area is clean and free from foreign material.






  • When installing the fuel pump module, make sure to align the locator tabs on the Fuel Tank mounting flange.


  • When installing the fuel pump module locking ring, hold the O-ring while turning the locking ring until it stops against the retainer tabs.To install, reverse the removal procedure.




  • Start the engine and visually inspect for leaks.


  • Mazda Tribute Fuel Pump, In-Tank, New, Electric


    $88.07List Price $103.92Save $15.85Availability: In Stock

    SPECTRA PREMIUM FUEL PUMP
    $290.29List Price $342.54Save $52.25Availability: In StockNUIE0Q


    AIRTEX FUEL PUMP MODULE ASSEMBLYAirtex Fuel Pump is developed with the latest technological advancements in fuel delivery systems and not only complies with OE specifications but also improves upon fuel delivery.

Aug 19, 2013 | 2005 Mazda Tribute 3.0s

1 Answer

My gas gauge dosent work how can I fix it


You will need to remove the gas tank and replace the fuel level sensor inside the fuel tank.
The level sensor is part of the electric fuel pump "module" Here is how to change that part.
  • 1. Start the van's engine. Open the fuel cap and remove the fuel pump relay from the engine's fuse box. Look for the engine to stall, signaling that the fuel pressure is gone.
  • 2Disconnect the van's negative battery cable.
  • 3. Unbolt the fuel tank's straps and lower the tank just enough to access the fuel pump flange. You can have a second person lower the tank, but it might be easier to use a floor jack with a wood block.
  • 4Remove the small locking pin on the pump's electrical connector with needle-nose pliers, and disconnect the electrical connector. Press the retainer tabs on the fuel lines and disconnect them from the pump.
  • 5Unscrew the pump's locking ring with a strap wrench or a similar hand-made tool that can grip the large ring and turn it.
  • 6Pull the water pump out of the tank, then remove and discard the O-ring from the fuel tank.
  • 7Pry back the locking tabs connecting the inlet filter to the pump reservoir using a thin screwdriver and remove the filter. This is only needed if this filter is in good condition and you must transfer it to the new pump.
Installation
  • 8Lubricate the O-ring for the filter with engine oil and connect it to the outlet of the filter. Push the filter onto the pump reservoir's inlet and make sure the locking tabs engage.
  • 9Install a new O-ring onto the seating hole on the fuel tank.
  • 10Insert the pump module into the tank, tilting it at an angle and making sure you don't damage the filter or the pump float. Make sure the module is properly seated.
  • 11Screw the retaining ring into position on the pump module.
  • 12Reconnect the fuel lines to the pump using their quick-connect fittings and the electrical connector with its locking pin.
  • 13Connect the tank back to the van using its straps and strap bolts.
  • 14Reconnect the fuel pump relay and negative battery cable

Jul 02, 2012 | 2000 Chrysler Grand Voyager

2 Answers

Where is fuel pump for 1996 mercury mystique located on the car and how do you remove it


SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Multi-Port Fuel Injection (MFI) Fuel Pressure Gauge T80L-9974-B
Removal
  1. Depressurize fuel system as outlined in Service Procedures- Fuel System Pressure Relief.
  1. Remove rear seat cushion. Refer to Section 01-10.
  1. Remove plastic grommet from floor pan.
  1. Disconnect fuel pump module electrical connector.
  1. NOTE: To disconnect fuel tubes from fuel pump module, compress tabs on both sides of each nylon push connect fitting and ease fuel tube out of fuel pump module.

    Disconnect fuel and vapor return tubes from fuel pump module.
  1. Turn fuel pump locking retainer ring counterclockwise using Fuel Tank Sender Wrench D84P-9275-A or equivalent and remove fuel pump locking retainer ring.
  1. NOTE: After fuel pump module removal, immediately cover fuel pump module opening in fuel tank in order to prevent fuel system contamination.

    Remove fuel pump module and cover fuel pump module opening in fuel tank.
  1. Remove fuel pump module O-ring seal and discard.
Installation
  1. NOTE: When cleaning fuel pump module mounting surface on fuel tank, use caution to prevent any foreign material from entering fuel system.

    Clean fuel pump module mounting flange and fuel pump module mounting surface and O-ring seal groove on fuel tank.
  1. Apply a light coat of Premium Long-Life Grease XG-1-C, -K or equivalent meeting Ford specification ESA-M1C75-B on a new O-ring seal to hold it in place and install it into the O-ring seal groove on the fuel tank.
  1. Install fuel pump module carefully to ensure that filter is not damaged. Make sure that locating keys are in keyways and O-ring seal remains in place.
  1. Hold fuel pump module in place and install fuel pump locking retainer ring finger-tight. Make sure that all locking tabs are under fuel tank lock ring tabs.
  1. Secure fuel pump locking retainer ring by rotating clockwise using Fuel Tank Sender Wrench D84P-9275-A or equivalent until fuel pump locking retainer ring rests against stops.
  1. Connect fuel and vapor return tubes to fuel pump module.
  1. Connect fuel pump module electrical connector.
  1. Install plastic grommet in floor pan.
  1. Install rear seat cushion. Refer to Section 01-10.
  1. Install Multi-Port Fuel Injection (MFI) Fuel Pressure Gauge T80L-9974-B as outlined in Service Procedures-Fuel System Pressure Relief.
  1. Turn ignition switch to RUN position for three seconds repeatedly (5 to 10 times) until pressure gauge reads at least 270 kPa (30 psi). Check for leaks at fittings.
  1. Remove pressure gauge, start engine and recheck for leaks.
Hope this helps

Aug 13, 2011 | 1996 Mercury Mystique

1 Answer

How do you change the fuel pump?


Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect the negative battery cable.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Rear seat cushion
    • Plastic access panel
    • Fuel pump wiring harness connector
    • Fuel lines
      7922jg34.gif

      View of fuel pump fittings through the floor pan
      Click to Enlarge 7922jg35.gif

      Remove the locking ring from the fuel pump sender with special tool Fuel Tank Sender Wrench D84P-9275-A
      Click to Enlarge

    • Fuel pump module lock ring. Use special tool Fuel Tank Sender Wrench D84P-9275-A.
    • Fuel pump module

To install:

  1. Install or connect the following:
    • Fuel pump module with a new O-ring seal
    • Fuel pump module lock ring using special tool Fuel Tank Sender Wrench D84P-9275-A
    • Fuel lines
    • Fuel pump wiring harness connector
    • Plastic access panel
    • Rear seat cushion
    • Negative battery cable
  2. Start the engine and check for leaks and proper operation.
shinehutt_37.gif

hope this helps plz vote comment reply if need more help

Jan 17, 2011 | 2002 Mercury Cougar

1 Answer

2005 toyota corolla. no problems yesterday..this morning it was dead. I can jump it and it turns over but it won't stay running. doesn't seem to be getting any fuel. Which fuse could be causing this...


Fuel Pump-(test for current at the fuel pump using a multimeter or test light while cranking) Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Relieve fuel system pressure.
  3. Disconnect the battery ground cable.
  4. Remove the rear seat cushion.
  5. Remove the rear floor service cover mounting screws and remove the cover (except '02-'04). toy_car_cor-02-04fuelpump2.gif

  6. Remove the butyl tape and remove the floor service cover ('02-'04).
  7. Remove the fuel pump vapor pressure sensor electrical connector ('02-'04).
  8. Remove the fuel line U-clip and remove the fuel line from the fuel pump module.
  9. Squeeze the fuel vent line retainer and remove the vent line from the fuel pump module. toy_car_cor-02-04fuelpump1.gif

  10. Remove the 8 fuel pump module retainer ring mounting screws and remove the retainer ring ('02-'04).
  11. Remove the fuel pump module retainer using special tool 09808- 14020 or equivalent (except '02-'04).
  12. Remove the fuel pump module.
To Install:
  1. Install a new O-ring on the fuel tank.
  2. Install the fuel pump module into the fuel tank.
  3. Use the following procedure to install the fuel pump module retainer ring (except '02-'04). Fuel pump module installation toy_cor-05-18-1203.gif

    1. Align the notch in the fuel tank with the tab in the module.
    2. Matchmark a new retainer with the fuel tank.
    3. Using the special tool install and tighten the retainer ring 2 revolutions.
  4. Use the following procedure to install the fuel tank module retainer ring ('02-'04).
    1. Install the retainer ring on the fuel pump module.
    2. Fasten the retainer with the 8 mounting screws. Tighten 53 in lb (6 Nm).
  5. Install the vent line to the pipe until the fuel vent line connector clicks into place.
  6. Install the fuel line with the U-clip.
  7. Install the fuel pump vapor pressure sensor electrical connector ('02-'04).
  8. Install the floor service cover with butyl tape ('02-'04).
  9. Install and secure the rear floor service cover with the mounting screws (except '02-'04).
  10. Install the rear seat cushion.
  11. Connect the battery ground cable.
  12. Check for fuel leaks.
prev.gif next.gif

Oct 16, 2010 | 2005 Toyota Corolla

2 Answers

How do you change the fuel pump? is there a access panel and if so where is it located?


Removal & Installation
To Remove:


  1. Before servicing the vehicle, refer to the precautions at the beginning of
    this section.
  2. Release fuel pressure.
  3. Remove or disconnect the following:

    • The rear seat





      Electrical Connector
      dod_intrpd_fuel__tank_elec_conn.gif



    • The fuel pump electrical connector





      Battery Cable
      dod_intrpd_batt_conn.gif



    • Battery cable

  4. Raise and safely support the vehicle
  5. Remove or disconnect the following:





    Fuel Tank Drain
    dod_intrpd_fuel_tank_drain.gif




    • Fuel from fuel tank





      Stabilizer Bar
      dod_intrpd_stab_bar.gif








      Stabilizer Bar and EVAP Canister
      dod_intrpd_evap_cann.gif



    • The rear stabilizer bar brackets from body
    • Stabilizer bar toward rear of vehicle





      Fuel Filler Tube
      dod_intrpd_filler_tube.gif



    • The fuel filler tube from fuel tank





      Fuel And EVAP Lines
      dod_intrpd_fuel_evap_lines.gif



    • Fuel and EVAP lines

  6. Position transmission jack under fuel tank assembly.
  7. Remove fuel tank straps bolts passenger side first.
  8. Lower fuel tank and remove the purge line and vent line.
  9. Disconnect fuel line from fuel pump module by depressing quick connect
    retainers with thumb and fore finger.
  10. Slide fuel pump module electrical connector lock to unlock.
  11. Disconnect the electrical connection from the fuel pump module, by pushing
    down on connector retainer and pulling connector off of module.





    Fuel Tank Locknut
    dod_intrpd_fuel_tank_tool__nut.gif



  12. Use Special Tool # 6856 to remove fuel pump module locknut.
  13. Remove fuel pump and O-ring seal from tank. Discard old seal.

To Install:


  1. Wipe seal area of tank clean and place a new seal in position in the tank
    opening.





    Fuel Tank Locator
    dod_intrpd_fuel_pump_loctr.gif



  2. Position fuel pump in the tank.

    • Make sure the alignment tabs on the underside of the fuel pump module flange
      sits in the notches on the fuel tank.

  3. Position the locknut over the fuel pump module.
  4. Tighten the locknut using Special Tool # 6856

    • Torque to: 40.5 ft. lbs. (55 Nm)

    CAUTION
    Over tightening the pump lock ring may
    result in a leak.

  5. Position the fuel tank on the transmission stand.
  6. Install or connect the following:

    • Fuel pump electrical connector into hole in the body
    • The purge and vent lines
    • Fuel tank and tank straps
    • The fuel filler tube and tighten the clamp
    • The stabilizer bar and install bolts

  7. Lower vehicle.
  8. Install or connect the following:

    • The fuel pump electrical connector that is in the rear seat
    • The rear seat
    • The battery cable

  9. Fill fuel tank.
  10. Use the DRB or equivalent scan tool to pressurize the fuel system.
  11. Check for leaks.


prev.gif next.gif

Sep 23, 2010 | 1999 Chrysler Concorde

1 Answer

How to change a fuel pump on a 2005 Nissan


Nissan Car Altima & Sentra 1999-06 Repair Guide
Fuel Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the pressure from the fuel system.
  3. Remove or disconnect the following:
    NOTE When the fuel sending unit needs to be removed, pull the tab upwards. The tab is located on the sending unit, opposite the end of the float. After the tab is pulled, the sending unit will lift straight out of the tank bracket.
    Negative battery cable Rear seat and the access cover Fuel pump electrical connector Fuel lines from the fuel pump assembly Locking ring Fuel gauge assembly Fuel tube and connector from the fuel gauge
    Fuel pump by pinching the 2 locking tabs together. Lift the fuel pump assembly straight upward and out of fuel tank. O-ring and discard
  4. Place a clean rag in the hole to keep out dirt.
To install:
  1. Remove the rag
  2. Install or connect the following:
    NOTE Verify that the mark on the fuel tank and the components are aligned when installing the pump and fuel gauge sending unit.
    New O-ring and fuel pump Electrical connection and fuel tube to the fuel gauge sending unit Fuel sending unit into the tank
  3. If equipped with a threaded lock ring torque the ring to 22-26 ft. lbs. (30-35 Nm). If equipped with a lock ring held by six retaining screws, torque the screws to 18-22 inch lbs. (2-2.5 Nm).
    Fuel lines and fuel pump electrical connector. Always install new clamps on the fuel lines. Negative battery cable
  4. Start the engine, check for leaks and repair if necessary.
    Fuel pump access cover Rear seat

The fuel pump is located in the fuel tank on all vehicles. In-tank fuel pumps are accessible by lifting up the rear seat to gain access to the inspection cover.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Rear seat from the vehicle Inspection cover that is located under the rear seat Inlet and outlet fuel lines from the fuel pump assembly Fuel pump and gauge wiring connections 6 mounting bolts that secure the fuel pump assembly to the top of the fuel tank
  4. Raise up the fuel pump assembly and detach the fuel tubes and connector.
    Fuel gauge assembly Fuel pump with the fuel chamber
  5. Pull up the front of the fuel pump chamber and slide the chamber forward.
    Fuel pump from the chamber O-ring seal or gasket
To install:
  1. Install or connect the following:
    Fuel pump to the fuel pump chamber and slide chamber rearward Fuel pump with the fuel pump chamber Fuel gauge assembly using a new O-ring Fuel tubes and connector. Use new hoses and clamps. 6 mounting bolts to the top of the fuel gauge unit and torque the bolts to 18-22 inch lbs. (2-2.5 Nm) Fuel pump and gauge wiring connections New inlet and outlet fuel lines to the fuel pump assembly Negative battery cable
  2. Start the vehicle, check for leaks and repair if necessary. Inspection cover and the rear seat

Hope helps (remember comment and rates this).

Jul 07, 2010 | 2005 Nissan Sentra

2 Answers

How do i replace fuel pump on 1998 escort se 2.0


Removal & Installation WARNING Extreme caution should be taken when removing the fuel tank from the vehicle! Ensure that all removal procedures are conducted in a well ventilated area! Have a sufficient amount of absorbent material in the vicinity of the work area to quickly contain any fuel spillage. NEVER store waste fuel in an open container, as it presents a serious fire hazard!

This procedure will require a new fuel pump gasket for pump installation, so be sure to have one before starting.
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove the rear seat cushion and unplug the electrical connectors from the fuel pump.
  4. Unfasten the four pump access cover screws and remove the cover.
  5. If equipped, unplug the pump electrical connector located under the cover.
  6. Unfasten the fuel line clip(s) and disconnect the line(s) from the pump.
  7. Use a fuel pump locking ring removal tool or a brass drift and a hammer to unfasten the pump locking retaining ring.
  8. Remove the fuel pump and the gasket from the tank.


ac8ef02.gif

To install:
  1. Install a new gasket and place the pump into position in the tank.
  2. Install the pump locking retaining ring.
  3. Connect the fuel line(s) to the pump and install the line retaining clip(s).
  4. If equipped, attach the fuel pump electrical connection(s).
  5. Install access cover, then tighten the retainers.
  6. Attach the pump electrical connector(s).
  7. Install the rear seat cushion.
  8. Connect the negative battery cable.
  9. Start the car and check for proper operation.

May 13, 2010 | 1998 Ford Escort

1 Answer

Fuel pump


remove as much dust and dirt first. use a big hammer and a LARGE screwdriver. Place the driver tip against one of the tabs of the ring and hit it in a counter clockwise direction to remove the ring. ring is used to compress the oring seal to seal tank. to install hit it the other way

Mar 13, 2010 | 1991 Honda Civic

1 Answer

How do you change fuel pump on a 04 dodge intrepid?


hope this helps...
Pump Module—Left Side
  1. Release the fuel pressure.
  2. Disconnect negative battery cable.

    NOTE The fuel level of the vehicle must be below 5/8 of a tank before you remove the module lock-rings. If it is above that you can spill fuel in the vehicle.

  3. Drain partial fuel from fuel tank through the filler tube. Use a hard nylon tube, with a 30° cut on the end, to push the check valve open to drain fuel from tank.
  4. Remove the rear lower seat cushion.
  5. Push seat back and up to remove seat cushion.
  6. Fold back the foam pad covering access cover for modules.
  7. Disconnect the electrical connector from left side module.
  8. Mark the module orientation.
  9. Use special tool 9340 to remove left side module lock ring.
  10. Drain fuel from left side of fuel tank. Lift module up enough to push hose into tank and drain. Do not spill fuel in interior of vehicle.
  11. Disconnect the electrical connector for the left side fuel level card from bottom of the module top.
  12. Disconnect the electrical connector for the right side fuel level sending card.
  13. Lift module top half off and tip lower half on its side to drain remaining fuel from the reservoir.
  14. Remove wire from module.
  15. Use a screwdriver to separate the locking tabs on the level sending card.
  16. Lift level sending card straight up and out of module.
  17. Disconnect the electrical wiring from module.
  18. Remove level sending card.
To install:
  1. Install level sending card, make sure that the locking tabs are locked on the card.
  2. Route wires in the proper location.
  3. Install module top to module bottom.
  4. Connect the electrical connectors for right side fuel level sending card, left side module card and fuel pump.
  5. Install module and align marks on the module for proper orientation.
  6. Install module lock-ring.
  7. Use special tool #9340 to tighten left side module lock ring.
  8. Connect the electrical connector to left side module and install plastic access cover.
  9. Fold the foam pad covering access cover for modules back into place.
  10. Install rear lower seat cushion
  11. Rear lower seat cushion installed.
  12. Fill fuel tank.
  13. Connect negative battery cable.
  14. Fill fuel tank. Use the scan tool to pressurize the fuel system. Check for

Jan 28, 2010 | 2004 Dodge Intrepid

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

275 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...