Question about 1996 Chrysler Town & Country

1 Answer

Replaced fuel pump and filter and camshaft sensor and crankshaft sensor will crank but not start.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 84 Answers

Try replacing the coil and distribitor as well as rotor button. Also before you go sinking to much more money in find out if its getting fuel or a spark. Crank the engine over several times and pull a plug see if its wet and smells like gas if so your getting fuel. Then pull a plug and ground the firing end on the engine block witht the other end still connected into the boot. Have some crank over the engine and see if you can see a spark, If so you have spark. CAUTION do not hold onto the plug wire and boot when the car is being turned over. you will get a big sock, it wont hurt you but it will hurt like hell.

Posted on Oct 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why bmw 2006 318 wont turn over


no gas, weak battery, crankshaft or camshaft sensor is bad, fuel pump bad, fuel pump relay or fuse is bad, haven't pushed clutch down far enough(rug caught underneath), fuel filter clogged, ignition coils bad. You need to give a hint as to what you have tried. Does it crank but not start/ Does it simply click(starter) and not crank/

Aug 15, 2014 | 2006 BMW 318 Ci

1 Answer

Why wont my 2003 bmw start


No gas, weak battery, crankshaft or camshaft sensor is bad, fuel pump bad, fuel pump relay or fuse is bad, haven't pushed clutch down far enough(rug caught underneath), fuel filter clogged, ignition coils bad. You need to give a hint as to what you have tried. Does it crank but not start? Does it simply click(starter) and not crank?

Aug 11, 2014 | BMW 745i Cars & Trucks

1 Answer

Freelander 04 does not start... but will crank.... pressure is at 53 ... i changes the camshaft sensor and crankshaft sens


When you turn the ignition on can you hear the fuel pump run for a second or so? If not could be faulty fuel pump.

Apr 03, 2014 | 2004 Land Rover FreeLander

1 Answer

Starting issues


Yes, the crank shaft position sensor tells the engine when to send fuel and spark to the cylinders in conjunction with the camshaft position sensor. If the crank sensor isn't working properly, the engine doesn't know when do do anything. Depending on what the other codes where, I'd highly suspect the CPS. It's not terribly hard to get at nor expensive of a part, but you will need a diagnostic scanner capable of doing a Crankshaft Learn procedure.

Jan 13, 2014 | 1999 GMC Jimmy

1 Answer

I have a 94 chrysler concorde. The problem is it won't start, I have replaced the fuel pump and the fuel pump relay fuse. And it still won't start. What should I do now?


check see if you getting spark if not.have vechicle code scan could have faulty ECM .faulty camshaft sensor and crankshaft sensor.make sure engine has been tuned up.replace fuel filter change spark plugs and wires. before engine can run need fuel and spark.either one not working car will not crank.

Jan 12, 2013 | Cars & Trucks

1 Answer

Car cranks but will not start. stars for 2-3 seconds. full pump is good. would it be the crank sensor? no codes


It sounds like you need a new fuel filter. It runs until the fuel runs out and the fuel filter is preventing the fuel pump from reaching the correct fuel pressure. If the fuel filter doesn't fix the problem, you might have a bad crankshaft or camshaft position sensor, but this would usually cause the vehicle to die once it has warmed up a bit (when the timing starts to advance).

Oct 12, 2011 | 2003 Ford Escape

1 Answer

Car takes a long time to start, like a few minutes. Runs fine once it finally starts. It gets closer the longer you crank. Changed pugs, fuel filter and some vacuum/pcv pieces, No difference.


FUEL PUMP GETTING BAD THE CHECK VALVE LETTING ALL FUEL DRAIN BACK TO FUEL TANK.HAVE VECHICLE SCAN FOR CRANKSHAFT SENSOR FAULTS. CAMSHAFT SENSOR FAULTS.

Dec 22, 2010 | 2002 Audi A4

2 Answers

Engine will crank but will not start and run.


Change the fuel filter first! It is located on most models passenger side center to rear center of van & tucked up near frame rail. Good luck!

Dec 01, 2009 | 1999 Ford Windstar

Not finding what you are looking for?
1996 Chrysler Town & Country Logo

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...