Question about Chevrolet Camaro

1 Answer

2.8 Multiport FI V6 motor in 1989 camaro. AutoZone and Advanced Auto can't find the right oil pressure sensor for it. What is it?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 5,763 Answers

Heres the oil preasure switch for your car, this is a napa part and the part # is OP6676, heres a picture of the correct switch hope this helps. i was trying to send a picture but i geuss the website has a problem, il try one more time.2.8 Multiport FI V6 motor - 467b555.jpg

Posted on Oct 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Po521 code on a 2010 Camaro ss


Possible causes
- Low oil level or motor mechanical fault
- Faulty oil pressure sensor
- Oil Pressure Sensor harness is open or shorted
- Oil Pressure Sensor circuit poor electrical connection

When is the code detected?
The P0521 is detected when the signal sent from oil pressure sensor to PCM goes out of range.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Oil pressure warning light ON.
P0521 Chevrolet Description
The PCM continuously monitors the engine oil pressure. The Oil Pressure Sensor/Switch sends a signal to the PCM when the engine is running.

Oct 30, 2013 | 2006 Jeep Commander Limited

1 Answer

How difficult is it to change the oil pump in a 1998 camaro(3800 V6)?


Should be inside the timing cover. You remove the timing cover to access the pump parts. Not really a pump assembly like pumps mounted inside oil pans.
I doubt the pump is faulty.
Have you checked the oil pressure with a mechanical gauge ?

Dec 18, 2012 | 1998 Chevrolet Camaro

2 Answers

Distributor hole oil leak on a 1993 chevy camaro 3.4 v6


The distributor shaft is worn, replace the distributor.

Oct 30, 2012 | Cars & Trucks

2 Answers

Check engine light has come on suddenly.Oil is up to ok on dip stick but I think the pressure guage is low


Find the closest AutoZone or Advanced Auto store. As long as the engine sounds ok it probably is ok. Assuming your oil is ok( it sounds like it is). Go to the store, they will scan the computer codes for you free and tell you why the light came on. they can also reset the light so it goes out until the next problem is sensed by the computer. good luck, worm1855

Jan 17, 2011 | 1989 GMC Sierra

1 Answer

Where is the location of the coolant fan switch temperature sensor?


V6 2.8L top right rear of engine. Fan also turns on through A/C pressure switch and coolant temperature sensor, but these should operate independent of the coolant temp switch.
V8 5.0L and 5.7L (Heavy Duty) lower right rear of engine above starter.
Base model V8 uses the coolant sensor (top right of engine) and A/C pressure switches (lower right corner of eng compartment on A/C line to turn on the cooling fan. Fan is energized on all applications through the cooling fan relay.

Mar 03, 2010 | 1989 Chevrolet Camaro

1 Answer

92 camaro fan problem


There is a temp sending unit and a temp sensor.One in the cylinder head between the spark plugs and the other in the intake manifold.If you've replaced both w/no success and insist on tryin the ecm you can swap it only if the other Camaro is the same fuel system (TBI for TBI or multiport for multiport).I've done this quite a few times.The Ecm is under the passenger side dash area where a glove compartment "would be."You'll need a 7mm socket and I think a 10mm socket.To remove the ecm harness plugs you'll have to slide out the little plastic pin locks holding the plugs in.

Sep 04, 2009 | 1992 Chevrolet Camaro

1 Answer

Low oil or no pressure


Are you sure it's your oil pump and not just a faulty oil sensor. Don't know if you have a V6 or a V8 so can't really help you more on where the sensor's are.
note: you get your oil pressure from the crankshaft and the oil pump really brings the oil to the top of the engine to keep it simple. 
Good luck and hope this keeps it really simple and save's you money.

Apr 09, 2009 | 1998 Chevrolet Camaro

1 Answer

Repairing rear suspension on 1989 RS Camaro now


try Schram auto and truck parts they sell only GM parts 1-800-292-1032 and you can also try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 12, 2009 | 1989 Chevrolet Camaro

1 Answer

Oil problems


Does it spin sluggish or faster than normal or normal ? If it was the oil pump it would still start. Unless the motor is locked because of lack of oil.

Jan 18, 2009 | 1992 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...