Question about 2000 Chevrolet Silverado 1500

1 Answer

Correct torque for mounting bolts on 2000 silverado pkup starter

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 4 Answers

35 ft. pds.

Posted on Oct 10, 2010

  • debjobo Oct 10, 2010

    Thanks! Response time was awesome!

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing a starter in a sebring 2006


All of the nuts and bolts are metric on it. It helps to use a 13mm swivel socket on the starter bolts but you can use a wrench if you need to. Also, a 7/8 open end wrench for the 02 sensor, or an 02 sensor socket.


Let me give you the steps for the starter and also the front engine mount bracket. You don't have to remove the entire mount, just the bracket




REMOVAL

  1. Open Hood.
  2. Disconnect the negative battery cable.
  3. Raise vehicle and support.
  4. Disconnect the electrical connector from the 02 sensor.



2009-10-31_143231_starter1.gif




  • Remove the 02 sensor from the exhaust manifold .
  • Remove the front mount through bolt.
  • Remove the front mount bracket from engine block.







  • 2009-10-31_143306_starter2.gif



    Remove the battery cable from starter.




    2009-10-31_143343_starter3.gif



    1. Remove the lower starter bolt and remove starter.

    INSTALLATION

    1. Install starter to transmission.
    2. Start the upper starter bolt.
    3. Start the lower bolt and snug it so that the starter will not move.
    4. Remove the upper bolt.
    5. Connect the battery cable and torque nut to 8.5 Nm (75 in. lbs.).
    6. Install the front mount bracket and check heat shield location.
    7. Install bolt the upper bolt and torque bolt to 54 Nm (40 ft. lbs.)
    8. Install the lower and torque bolt to 54 Nm (40 ft. lbs.)
    9. Install the front mount through bolt and torque bolt to 61 Nm (45 ft.. lbs.)
    10. Install the 02 sensor and torque to 27 Nm (20 ft. lbs.)
    11. Lower vehicle.
    12. Connect the negative battery cable.




    FRONT MOUNT

    REMOVAL

    1. Raise vehicle.




    2009-10-31_143650_mount1.gif



    1. Remove front mount to bracket horizontal through bolt (Fig. 87).
    2. Loosen the rear mount through bolt.
    3. Remove front mount vertical bolts (Fig. 87).
    4. Remove front mount and separate the starter heat shield.

    INSTALLATION

    1. Position front mount on lower radiator crossmember.
    2. Loose install front mount to bracket through bolt.
    3. Install front mount vertical bolts. Tighten bolts to 61 Nm (45 ft. lbs.) . (Fig. 87).NOTE: Be sure the weight of the engine is static and in rest position. this for a 2.7 v6

    Jan 15, 2012 | 2006 Chrysler Sebring

    1 Answer

    How do i change the starter on a 1997 buick park avenue?


    Removal & Installation To Remove:
    Starter 9306xg03.gif

    1. Before servicing the vehicle, refer to the service precautions in the beginning of this section
    2. Disconnect the battery negative cable
    3. Raise and support the vehicle
    4. Remove the transmission cooler line clip if necessary
    5. Remove the torque converter cover
    6. Disconnect the battery positive cable from the starter
    7. Disconnect the wire from the starter solenoid S terminal
    8. Remove the 2 starter motor mounting bolts and the starter motor
    To Install:
    1. Install the starter motor
      • Torque the mounting bolts to 32 ft-lbs (43 Nm)
    2. Connect the battery positive cable to the starter
      • Torque nut to 12 ft-lbs (16 Nm) (1997-2000);
      • Torque nut to 89 in-lbs (10 Nm) (2001-2005)
    3. Connect the starter motor S terminal wire
      • Torque nut to 22 in-lbs (2.5 Nm)
    4. Install the torque converter cover
      • Torque the bolts to 115 in-lbs (13 Nm)
    5. Attach the transmission cooler line clip
    6. Lower the vehicle
    7. Reconnect the negative battery cable
    prev.gif next.gif

    Dec 09, 2010 | Buick Park Avenue Cars & Trucks

    1 Answer

    Where is the starter located on my 2003 nissan sentra ser


    Starter Motor -located to articulate with flywheel that has gear teeth between the engine and transmission accessible from down below. REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
    3. Lightly lower the transmission to make room and pull out the dipstick tube.
    4. Remove or disconnect the following:
      • Negative battery cable
      • Connector bracket from the front mount bracket
      • Harness connector
      • Starter bolts
      • Starter
      To install:
    5. Install or connect the following:
      • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
      • Harness connector
      • Connector bracket to the front mount bracket
      • Dipstick tube
      • Transmission into position
      • 4 rear mounting bracket bolts
      • Negative battery cable
    6. Remove the transmission jack
    WITH MANUAL TRANSMISSION
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Remove or disconnect the following:
      • Negative battery cable
      • Connector bracket from the front mount bracket
      • Harness connector
      • Starter bolts
      • Starter
      To install:
    3. Install or connect the following:
      • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
      • Harness connector
      • Connector bracket to the front mount bracket
      • Negative battery cable
    1.6L and 2.0L Engines
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Remove or disconnect the following:
      • Negative battery cable
      • Wiring at the starter
      • Bolts attaching the starter to the engine
      • Starter
      To install:
    3. Install or connect the following:
      • Starter and torque the bolts to 70 inch lbs. (8 Nm)
      • Starter electrical connections
      • Negaative battery cable
    Maxima
    1. Remove or disconnect the following:
      • Negative battery cable
      • Air duct
      • Harness protector from the harness
      • Starter wiring at the starter
      • Starter-to-engine bolts
      • Starter from the vehicle

        Image 89612G12l Not Found

      To install:
    2. Install or connect the following:
      • Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) and the short bolt to 22-30 ft. lbs. (30-41 Nm)
      • Starter wiring
      • Harness protector
      • Air duct
      • Negative battery cable
    Altima
    1. Remove or disconnect the following:
      • Negative battery cable
      • Air inlet tube
      • Harness bracket
      • Wiring at the starter
      • Starter
      To install:
    2. Install or connect the following:
      • Starter and torque the bolts to 60 inch lbs. (7 Nm)
      • Starter electrical connectors
      • Harness bracket
      • Air inlet tube
      • Negative battery cable

    Nov 03, 2010 | 2003 Nissan Sentra

    2 Answers

    How to pullout starter on 2000 gmc sierra 4 by 4


    4.3L Engine
    1. Remove or disconnect the following:

      Negative battery cable Bracket and shield Wires Mounting bolts and shims Starter
    To install:
    1. Install or connect the following:

      Starter Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm). Wires. Torque battery wire nut to 89 inch lbs. (10 Nm) and ignition nut to 18 inch lbs. (2 Nm). Bracket and shield. Torque the nuts to 53 inch lbs. (6 Nm). Negative battery cable

      c5acb83.jpg
      Fig. Exploded view of the starter motor-4.3L engines.


    1. Remove or disconnect the following:

      Negative battery cable Bracket and shield Wires Mounting bolts and shims Starter
    To install:
    Install or connect the following:

    Starter Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm). Wires. Torque battery wire nut to 89 inch lbs. (10 Nm) and ignition nut to 18 inch lbs. (2 Nm). Bracket and shield. Torque the nuts to 53 inch lbs. (6 Nm). Negative battery cable

    a557bbc.jpg
    Fig. Exploded view of the starter motor-4.3L engines.

    Hope help with this (remember rated and comment this).

    Mar 17, 2010 | 2000 GMC Sierra

    1 Answer

    How to change starter on 2000 chevy silverado


    These instructions are for a 5.3L. Unless it is a V6 or diesel, the instructions will be similar if you have a different gas V8.
    1. Disconnect the negative battery cable
    2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
    3. Remove the protective shields as necessary.
    4. Remove the starter solenoid shield.
    5. Remove the starter to transmission close out cover bolt.
    6. Disconnect the engine oil level sensor connection.
    7. Remove the front axle mounting bracket through bolt nut, if equipped with four wheel drive (4WD).
    8. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt, if equipped with 4WD.
    9. Remove the mounting bolts from the engine block.
    10. Slide the starter forward until the starter clears the transmission.
    11. Remove the starter transmission close out cover
      1. Disconnect the positive battery cable and wiring harness from the starter.
      2. Remove the starter from the vehicle.
        1. Connect the positive battery cable to the starter. Tighten Tighten the nut to 16 N.m (12 lb in) .
        2. Install the starter transmission close out cover.
          1. Install the mounting bolts to the engine block. Tighten Tighten the bolts to 50 N.m (37 lb ft) .
          2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated. if equipped with 4WD.
          3. Install the front axle mounting bracket through bolt nut, if equipped with 4WD. Tighten Tighten the nut to 90 N.m (67 lb ft) .
          4. Disconnect the engine oil level sensor connection.
          5. Install the starter to transmission close out cover bolt.
          6. Install the starter solenoid shield.
          7. Install the protective shields as necessary.
          8. Remove the safety stands.
          9. Lower the vehicle.
          10. Connect the negative battery cable. Tighten Tighten the bolts to 17 N.m (13 lb ft) .

    Oct 01, 2009 | 2002 Chevrolet Silverado

    1 Answer

    Starter for kia sportage 2000


    1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
    2. Drain the engine oil.
    3. Remove or disconnect the following:

      Negative battery cable Intake manifold bracket upper bolts Clutch release cylinder and move it aside, if equipped Intake manifold bracket lower bolts and remove the bracket Starter from the clutch, manual transmissions only Starter from the torque converter, automatic transmissions only Starter electrical connectors Move the transmission wire harness aside Starter


      0900c152801b0603.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the starter

    To install:
    1. Install or connect the following:

      Starter to the engine well Starter electrical connectors Lower intake manifold bracket and install the upper bolts Starter into position. When aligned properly torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket bolts to 40 ft. lbs. (54 Nm). Properly position the clutch release cylinder, if equipped. Torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket upper bolts to 40 ft. lbs. (54 Nm). Negative battery cable

    Jun 28, 2009 | 2000 Kia Sportage

    1 Answer

    Need the correct torque specs for 2004 silverado 1500 calipers


  • Tighten the 2 brake caliper mounting bolts to 108 Nm (80 ft. lbs.) . Caliper Mounting Bracket to Knuckle, Front (15 series) 175 Nm (129 ft. lbs.) Caliper Mounting Bracket to Knuckle, Front (25/35 series) 300 Nm (221 ft. lbs.) Brake Caliper Mounting Bolt Rear (15 series) 42 Nm (31 ft. lbs.) Brake Caliper Mounting Bolt Rear (25/35 series) 108 Nm (80 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JC5/JH5) 200 Nm (148 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH6) 165 Nm (122 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH7) 300 Nm (221 ft. lbs.) Caliper Mounting Bracket Bolt Rear (NYS) 200 Nm (148 ft. lbs.)
    hope this helps
  • Mar 28, 2009 | 2004 Chevrolet Silverado

    2 Answers

    Changing the starter on my 99 tahoe


    Starter Escalade, Suburban, Tahoe, Yukon, Denali, Denali XL, Yukon XL, 1999 – 2005 REMOVAL&INSTALLATION
    Removal & Installation
    4.8L, 5.3L And 6.0L Engines
    CAUTION Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures.
    1. Disconnect the negative battery cable.
    2. Raise and support the vehicle.
    3. Remove or disconnect the following:
      • Protective shields, as necessary
      • Starter solenoid shield
      • Starter-to-transmission close out cover bolt
      • Engine oil level sensor connection
      • On 4WD, front axle mounting bracket through bolt nut
    4. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
      • Mounting bolts from the engine block. Slide the starter forward until the starter clears the transmission.
      • Starter transmission close out cover
      • Positive battery cable and wiring harness from the starter
      • Starter from the vehicle 0900c152800a6916.jpgStarter removal—4.8L, 5.3L and 6.0L engines
    To install:
    1. Install or connect the following:
      • Starter
      • Positive battery cable to the starter. Tighten the nut to 12 ft. lbs. (16 Nm).
      • Starter transmission close out cover
      • Mounting bolts to the engine block and tighten to 37 ft. lbs. (50 Nm)
    2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
      • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
      • Engine oil level sensor connection
      • Starter-to-transmission close out cover bolt
      • Starter solenoid shield
      • Protective shields as necessary
    3. Remove the safety stands.
    4. Lower the vehicle.
    5. Connect the negative battery cable.
    5.7L And 7.4L Engines
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Remove or disconnect the following:
      • Negative battery cable
      • Mounting bolts and shims
      • Wires
      • Heat shield
      • Starter
    To install:
    1. Install or connect the following:
      • Starter
      • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
      • Heat shield. Torque the bolts to 53 inch lbs. (6 Nm) and the nuts to 35 inch lbs. (3 Nm).
      • Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm).
      • Negative battery cable
    6.5L Engine
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Remove or disconnect the following:
      • Negative battery cables
      • Mounting bolts/nuts and shim, if used
      • Starter
      • Wires
      • Heat shield and bracket 0900c152800a6917.jpgExploded view of the starter motor—6.5L engine
    To install:
    1. Install or connect the following:
      • Heat shield and bracket. Torque the bolts to 13 ft lbs. (17 Nm).
      • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
      • Starter
      • Mounting bolts/nuts and shim, if used. Torque the bolts to 33 ft lbs. (45 Nm) and the nut to 75 inch lbs. (8.5 Nm).
      • Negative battery cables
    8.1L Engine
    1. Remove or disconnect the following:
      • Negative battery cable
      • On 4WD, front axle mounting bracket through bolt nut
    2. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
      • Positive battery cable nut
      • Positive cable from the solenoid
      • Engine harness ground nut and ground from the solenoid
      • Mounting bolts and starter
      • Heat shield bolts, nut and shield, if necessary
    To install:
    1. Install or connect the following:
      • Heat shield, bolts and nut if removed. Tighten the bolts to 35 inch lbs. (3 Nm) and the nut to 44 inch lbs. (5 Nm).
      • Starter and bolts. Tighten to 37 ft. lbs. (50 Nm).
      • Ground wire and nut. Tighten to 30 inch lbs. (3.4 Nm).
      • Positive cable and nut. Tighten to 80 inch lbs. (9 Nm).
    2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
      • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
      • Negative battery cable

    Sep 28, 2008 | 1999 Chevrolet Tahoe

    1 Answer

    Replacing starter 02 silverado 6.6


    1. Remove or disconnect the following:
      • Negative battery cables
      • Right front wheel and fender splash shield, on 6.6L engines
      • Turbocharger exhaust pipe, on 6.6L engines
      • Mounting bolts/nuts and shim, if used
      • Starter
      • Wires
      • Heat shield and bracket 0900c152801cad96.jpgExploded view of the starter motor-6.5L engine shown
    To install:
    1. Install or connect the following:
      • Heat shield and bracket. Torque the bolts to 13 ft lbs. (17 Nm).
      • Wires.Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18inch lbs. (2 Nm) on 6.5L engines. On 6.6L engines, tighten the solenoidnut to 30 inch lbs. (3.4 Nm) and the positive battery cable nut to 80inch lbs. (9 Nm).
      • Starter
      • Mounting bolts/nuts and shim,if used. Torque the bolts to 33 ft lbs. (45 Nm) and the nut to 75 inchlbs. (8.5 Nm) for 6.5L engines. For 6.6L engines tighten the starterbolts to 58 ft. lbs. (78 Nm).
      • Turbocharger exhaust pipe, on 6.6L engines
      • Right front fender splash shield and wheel, on 6.6L engines
      • Negative battery cables

    Jul 30, 2008 | 2002 Chevrolet Silverado

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    20 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...