Question about 1994 GMC Jimmy

1 Answer

What and where is the heat stove tube - 1994 GMC Jimmy

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 2,002 Answers

The heat stove is a metal shield that covers one of your exhaust manifolds, usually the passenger side. It has a flexible pipe that runs to your air intake. When the engine is cold a valve in the intake opens and the engine pulls warm air from the manifold through the pipe.
Chances are the stove is missing from your truck, they tend to rust out at the mounting points and either fall off or get pulled off by someone who gets annoyed by the rattling they make. You can still run the pipe down to the manifold without the stove and it will do the job, just not as quick. The pipe can be got at an autoparts store but I think the stove is a dealer item. Ask to be sure. Hope this helps.

Posted on Oct 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i get my dipstick out of the tube after it broke off in my 2006 nissan sentra


Try it again. But first heat the tube up. A heat gun or small torch. Clean the tube before inserting a new one. The stuff that drops in the engine won't hurt it.

Feb 14, 2015 | 2006 Nissan Sentra

2 Answers

When I start my dryer, there's no heat. How can I fixed that?


Most likely the heating element is burned out. This is an element similar to the one in an electric stove oven. Often, this part is easy to access by removing a panel on the back of the dryer (You did unplug it first, right?).

Dec 27, 2014 | Cars & Trucks

1 Answer

Efel oil stove wont burn blue only yellow


Pull the crown and the two crown supports, scrape and vacuum the residual ash on the bottom and around the starter coil. Pull the and turn the oil feed tube scraper back out of the way. Reach inside the tube with a screwdriver and scrape out the residue until as clean as posssible. Exercise the fuel tube rod several times until there is no scraping sound. Vacuum the interior and replace the parts (Do not clean the crown).

Dec 23, 2012 | Cars & Trucks

1 Answer

How do I get the part where the plug for turn signal switch go thur this without cut and rewire it?


Take apart the tilt steering column, buy the small harness, and replace.
(Harness has turn signal switch, etc. on one end. Harness goes down the column, and plugs in; on the other end. Or cut wires, solder, and use heat shrink tubing. Slide heat shrink tubing up one wire BEFORE soldering. Slide down onto soldered connection of wire, heat ->heat shrink tubing )

Nov 20, 2012 | Cars & Trucks

1 Answer

Where and what is Tac Heat Stove


is it a stove thats special for cooking tacos by any chance

May 19, 2012 | 1988 Dodge Dakota

1 Answer

No heat in2002 saturn replacedthermostat but still no heat seems like antifreeze not cicculating


Verify whether the two tubes at firewall are getting hot, or one or the other is cold, or both are cold.
If the tubes don't get hot, then you won't get heat. If they are getting hot and you don't have heat, it's likely that the blend door actuator is not working properly to get heat from the heater core to the interior of the vehicle.

Jan 08, 2011 | 2001 Saturn SC

1 Answer

What is the heat transfur tube ? does the engine have to be pulled to repair ?--2001 dodge intrepid


The heat tranfer tube directs heat from the exaust to the intake manifold usually to heat the incoming fuel air charge to the cylinders of the engine to give better performance.Normally a good mechanic won't need to remove the engine.

Oct 08, 2010 | 2001 Dodge Intrepid

2 Answers

How do you remove the driver side exhaust manifold


sometime you have to use a little of heat or a hacksaw and replace them with new ones give these website a try www.alldatadiy.com and www.autozone.com wish you the best of luck Michigan Man.

Mar 28, 2010 | 1994 Chevrolet K1500

1 Answer

Need to know how to remove starter from 1991 dodge caravan


e
26065b4.jpg

Starter motor mounting-2.2L and 2.5L engines

- Working from under the vehicle, disconnect the starter motor heat shield clamp

fb70ec4.jpg

View of the starter motor with the heat shield removed while looking over the crossmember

-
Removing the starter motor mounting stud nut where the air pump tube bracket is also attached

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle. The starter can be removed by reaching over the crossmember.
  3. Remove the heat shield and its clamps, if so equipped.
  4. On the 2.2L and 2.5L engines, loosen the air pump tube at the exhaust manifold and move the tube bracket away from the starter.
  5. Remove the electrical connections from the starter.
  6. Remove the bolts attaching the starter to the flywheel housing and the rear bracket to the engine or transaxle.
  7. Remove the starter from the engine.

To install:
  1. Position the replacement starter against the mounting surface.
  2. Install the mounting bolts.
  3. Connect the starter wiring.
  4. On 2.2L and 2.5L engines, position the air pump tube toward the starter, then connect the tube bracket to the exhaust manifold.
  5. Install the heat shield and clamp.
  6. Connect the negative battery cable.

Hope helped with this (remember rated this help) Good luck.

Nov 03, 2009 | 1991 Dodge Caravan

Not finding what you are looking for?
1994 GMC Jimmy Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...