Question about 2002 Ford Mustang

1 Answer

Getting engine water from the exhaust pipe - 2002 Ford Mustang

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Very common in cracked heads or blown head gaskets. you should have the engine pressure tested to make sure. may even be a intake manifold gasket.

Posted on Oct 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace water pump on 1991 pontiac quad 4


2.3L Engine
  1. Disconnect the negative battery cable
  2. Detach the oxygen sensor connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for more complete coolant drain.
  4. Remove upper and lower exhaust manifold heat shields.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Break loose the manifold to exhaust pipe spring loaded bolts using a 13mm box wrench.
  7. Raise and safely support the vehicle. NOTE: It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  8. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.
  9. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  10. Remove the radiator outlet pipe from the oil pan and transaxle. If equipped with a manual transaxle, remove the exhaust manifold brace. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump.
  11. Carefully lower the vehicle.
  12. Remove the exhaust manifold, seals and gaskets.
  13. Loosen and reposition the rear engine mount and bracket for clearance, as required.
  14. Remove the water pump mounting bolts and nuts. Remove the water pump and cover assembly, then separate the two pieces.

Feb 23, 2012 | 1991 Pontiac Grand Am

1 Answer

Diragram on how to change the water pump on a 1995 z24 cavalier 2.3


Check this procedure, according with the repair guide for...

2.3L and 2.4L Engines
(see Figure 9)
  1. Disconnect the negative battery cable
  2. Detach the oxygen sensor connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break loose the manifold to exhaust pipe spring loaded bolts using a 13mm box wrench.
  8. Raise and safely support the vehicle.
It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  1. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  2. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.
On the 2.4L engines, DO NOT rotate the flex coupling more than 4° or damage may occur.Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  1. Remove the radiator outlet pipe from the oil pan and transaxle. If equipped with a manual transaxle, remove the exhaust manifold brace. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  2. Carefully lower the vehicle.
  3. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  4. For the 2.4L engine, remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  5. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces.

zjlimited_2033.jpg

Fig. 9: Water pump and cover mounting - 2.3L and 2.4L engines (click over image for zoom)

To install:

  1. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  2. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  3. Lubricate the radiator outlet pipe O-ring with antifreeze and slid the pipe onto the water pump cover. Install the bolts finger-tight.
  4. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts-19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly-106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first-19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover-125 inch lbs. (14 Nm).
  5. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  6. Raise and safely support the vehicle.
  7. Index the exhaust manifold bolts into the exhaust pipe flange.
  8. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  9. Connect the radiator outlet pipe to the transaxle and oil pan. Install the exhaust manifold brace, if removed.
  10. On the 2.4L engine, install the timing chain tensioner and front cover.
  11. Install the lower heat shield.
  12. Carefully lower the vehicle.
  13. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  14. Tighten the manifold-to-exhaust pipe nuts to specification.
  15. Install the upper heat shield.
  16. Attach the oxygen sensor connector.
  17. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  18. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine off.
  19. Once the vehicle has cooled, recheck the coolant level.

Hope helps; remember to rating this answer and leave a testimonial comment. Thank you for using FixYa.

Oct 13, 2011 | 1995 Chevrolet Cavalier

1 Answer

WHAT ARE THE TORQUE SPECS FOR A WATER PUMP ON A 2003 CHEVY MALIBU


Water Pump REMOVAL & INSTALLATION CAUTION
Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old. 2.4L Engine
  1. Disconnect the negative battery cable
  2. Detach the Oxygen (O2) sensor electrical connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for a more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break the manifold-to-exhaust pipe spring loaded bolts loose using a 13mm box wrench.
  8. Raise and safely support the vehicle. NOTE: It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  9. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  10. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt. NOTE: DO NOT rotate the flex coupling more than 4°or damage may occur.
  11. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  12. Remove the radiator outlet pipe from the oil pan and transaxle. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  13. Carefully lower the vehicle.
  14. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  15. Remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  16. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces. Fig. 1: Water pump and cover mounting - 2.4L engine 87953070.gif
    To install:
  17. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  18. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  19. Lubricate the radiator outlet pipe O-ring with antifreeze and slide the pipe onto the water pump cover. Install the bolts finger-tight.
  20. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts:19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly: 106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first: 19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover: 125 inch lbs. (14 Nm).
  21. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  22. Raise and safely support the vehicle.
  23. Index the exhaust manifold bolts into the exhaust pipe flange.
  24. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  25. Connect the radiator outlet pipe to the transaxle and oil pan.
  26. Install the timing chain tensioner and front cover.
  27. Install the lower heat shield.
  28. Carefully lower the vehicle.
  29. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  30. Tighten the manifold-to-exhaust pipe nuts to specification.
  31. Install the upper heat shield.
  32. Attach the oxygen sensor connector.
  33. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  34. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine OFF.
  35. Once the vehicle has cooled, recheck the coolant level, then install the radiator cap.
3.1L Engine
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Loosen, but do not remove, the water pump pulley bolts.
  4. Remove the serpentine belt.
  5. Unfasten the water pump pulley bolts, then remove the pulley.
  6. Remove the five water pump mounting bolts, then remove the water pump. To install: Fig. 2: View of the water pump mounting and bolt tightening specifications - 3.1L engine shown 86883115.gif

  7. Clean all the gasket surfaces completely.
  8. Apply a thin bead of sealer around the outside edge of the water pump along the gasket sealing area, then install the gasket onto the water pump.
  9. Position the water pump on the engine, then tighten the water pump mounting bolts to 89 inch lbs. (10 Nm).
  10. Install the water pump pulley and finger-tighten the pulley bolts.
  11. Install the serpentine belt.
  12. Tighten the water pump pulley bolts to 18 ft. lbs. (25 Nm).
  13. Fill the cooling system.
  14. Connect the negative battery cable, then start the engine. Let the engine run until it reaches normal operating temperature, then check for leaks and coolant level. Add coolant, if necessary, then turn the engine OFF.
prev.gif next.gif

Nov 03, 2010 | 2003 Chevrolet Malibu

1 Answer

How do I replace a water pump on a 1999 malibou with a quad 4?


Water Pump REMOVAL & INSTALLATION CAUTION
Never open, service or drain the radiator or cooling system when hot; serious burns can occur from the steam and hot coolant. Also, when draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantities. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old. 2.4L Engine
  1. Disconnect the negative battery cable
  2. Detach the Oxygen (O2) sensor electrical connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for a more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break the manifold-to-exhaust pipe spring loaded bolts loose using a 13mm box wrench.
  8. Raise and safely support the vehicle. NOTE: It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  9. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  10. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt. NOTE: DO NOT rotate the flex coupling more than 4°or damage may occur.
  11. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  12. Remove the radiator outlet pipe from the oil pan and transaxle. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  13. Carefully lower the vehicle.
  14. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  15. Remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  16. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces. Fig. 1: Water pump and cover mounting - 2.4L engine 87953070.gif
    To install:
  17. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  18. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  19. Lubricate the radiator outlet pipe O-ring with antifreeze and slide the pipe onto the water pump cover. Install the bolts finger-tight.
  20. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts:19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly: 106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first: 19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover: 125 inch lbs. (14 Nm).
  21. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  22. Raise and safely support the vehicle.
  23. Index the exhaust manifold bolts into the exhaust pipe flange.
  24. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  25. Connect the radiator outlet pipe to the transaxle and oil pan.
  26. Install the timing chain tensioner and front cover.
  27. Install the lower heat shield.
  28. Carefully lower the vehicle.
  29. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  30. Tighten the manifold-to-exhaust pipe nuts to specification.
  31. Install the upper heat shield.
  32. Attach the oxygen sensor connector.
  33. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  34. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine OFF.
  35. Once the vehicle has cooled, recheck the coolant level, then install the radiator cap.

Oct 26, 2010 | 1999 Chevrolet Malibu

1 Answer

Do i need to lift the engine up to acces the timeing chain cover to remove the water pump? on chev 1999 2.4l


Water Pump REMOVAL & INSTALLATION CAUTION
When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old. 2.2L Engine
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into an approved container.
  3. Remove all accessory drive belts or the serpentine belt.
  4. Remove the alternator and bracket. For details, please refer to Section 2 of this manual.
  5. Unscrew the water pump pulley mounting bolts and then pull off the pulley.
  6. Unfasten the mounting bolts, then remove the water pump.
  7. Using a putty knife, clean the gasket mounting surfaces. Fig. 1: Location and mounting of the water pump on the 2.2L engine 87953068.gif
    Fig. 2: If the pulley turns when you try to loosen the bolts, attach sockets and ratchets to two of the bolts, insert a prybar to hold the pulley in place and loosen the bolts - 2.2L engine 91113p41.jpg
    Fig. 3: Remove the pulley from the water pump 91143p90.jpg
    Fig. 4: The water pump is retained by four bolts, remove them and . . . 91143p85.jpg
    Fig. 5: . . . remove the water pump from the engine 91143p86.jpg
    Fig. 6: Thoroughly clean the gasket mating surfaces on the engine block as well as . . . 91143p87.jpg
    Fig. 7: . . . the water pump (if it is being reused) 91143p89.jpg
    Fig. 8: Always use a quality new gasket like this one from Fel-Pro® 91143p88.jpg
    To install:
  8. Place a 1?8 in. (3mm) wide bead of RTV sealant on the water pump sealing surface or install a new gasket, on models so equipped. Install the pump and tighten the retaining bolts to 18 ft. lbs. (25 Nm).
  9. Install the water pump pulley, then tighten the mounting bolts to 22 ft. lbs. (30 Nm).
  10. As outlined in Section 2, install the alternator and bracket.
  11. Install the drive belts or serpentine belt, as applicable.
  12. Fill the cooling system to the proper level.
  13. Connect the negative battery cable, then start the engine and check for leaks.
2.3L and 2.4L Engines
  1. Disconnect the negative battery cable
  2. Detach the oxygen sensor connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break loose the manifold to exhaust pipe spring loaded bolts using a 13mm box wrench.
  8. Raise and safely support the vehicle. NOTE: It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  9. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  10. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt. NOTE: On the 2.4L engines, DO NOT rotate the flex coupling more than 4°or damage may occur.
  11. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  12. Remove the radiator outlet pipe from the oil pan and transaxle. If equipped with a manual transaxle, remove the exhaust manifold brace. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  13. Carefully lower the vehicle.
  14. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  15. For the 2.4L engine, remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  16. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces. Fig. 9: Water pump and cover mounting - 2.3L and 2.4L engines 87953070.gif
    To install:
  17. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  18. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  19. Lubricate the radiator outlet pipe O-ring with antifreeze and slid the pipe onto the water pump cover. Install the bolts finger-tight.
  20. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts - 19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly - 106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first - 19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover - 125 inch lbs. (14 Nm).
  21. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  22. Raise and safely support the vehicle.
  23. Index the exhaust manifold bolts into the exhaust pipe flange.
  24. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  25. Connect the radiator outlet pipe to the transaxle and oil pan. Install the exhaust manifold brace, if removed.
  26. On the 2.4L engine, install the timing chain tensioner and front cover.
  27. Install the lower heat shield.
  28. Carefully lower the vehicle.
  29. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  30. Tighten the manifold-to-exhaust pipe nuts to specification.
  31. Install the upper heat shield.
  32. Attach the oxygen sensor connector.
  33. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  34. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine off.
  35. Once the vehicle has cooled, recheck the coolant level.
prev.gif next.gif

Sep 18, 2010 | 1998 Chevrolet Cavalier

2 Answers

How to replace water pump on 97 pontiac sunfire 2.4


PLEASE DON'T FORGET TO RATE! THANKS! 2.3L & 2.4L Engines
  1. Disconnect the negative battery cable
  2. Detach the oxygen sensor connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break loose the manifold to exhaust pipe spring loaded bolts using a 13mm box wrench.
  8. Raise and safely support the vehicle.
It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  1. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  2. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.
On the 2.4L engines, DO NOT rotate the flex coupling more than 4° or damage may occur.
  1. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  2. Remove the radiator outlet pipe from the oil pan and transaxle. If equipped with a manual transaxle, remove the exhaust manifold brace. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  3. Carefully lower the vehicle.
  4. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  5. For the 2.4L engine, remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  6. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces.

01add58.gif
Water pump and cover mounting-2.3L and 2.4L engines

To install:
  1. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  2. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  3. Lubricate the radiator outlet pipe O-ring with antifreeze and slid the pipe onto the water pump cover. Install the bolts finger-tight.
  4. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts-19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly-106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first-19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover-125 inch lbs. (14 Nm).
  5. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  6. Raise and safely support the vehicle.
  7. Index the exhaust manifold bolts into the exhaust pipe flange.
  8. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  9. Connect the radiator outlet pipe to the transaxle and oil pan. Install the exhaust manifold brace, if removed.
  10. On the 2.4L engine, install the timing chain tensioner and front cover.
  11. Install the lower heat shield.
  12. Carefully lower the vehicle.
  13. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  14. Tighten the manifold-to-exhaust pipe nuts to specification.
  15. Install the upper heat shield.
  16. Attach the oxygen sensor connector.
  17. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  18. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine off.
  19. Once the vehicle has cooled, recheck the coolant level.

Sep 13, 2010 | Pontiac Sunfire Cars & Trucks

2 Answers

Water pump


NOT HARD BUT YOU HAVE TO DRAIN COOLANT OUT OF SYSTEM.CATCHING IT IN A DRAIN PAN .THE 2.4 ENGINE YOU HAVE TO REMOVE. OXYGEN SENSOR THE EXHAUST MANIFOLD HEAT SHIELD.REMOVE COOLANT INLET HOUSING BOLT THROUGH THE EXHAUST MANIFOLD .REMOVE EXHAUST MANIFOLD BRACE TO MANIFOLD BOLT.REMOVE TO EXHAUST TO PIPE STUDS.REMOVE COOLANT INLET HOUSING TO WATER PUMP COVER BOLT.REMOVE EXHAUST PIPE FROM THE EXHAUST MANIFOLD BY PULLING IT DOWNWARD.REMOVE COOLANT INLET PIPE FROM THE OIL PAN.REMOVE BRAKE VACUUM PIPE FROM THE CAMSHAFT HOUSING.REMOVE EXHAUST MANIFOLD FROM THE CYLINDER HEAD.REMOVE HEATER HOSE FROM THE HEATER OUTLET PIPE.REMOVE THE TIMING CHAIN COVER AND TENSIONER.REMOVE WATER PUMP COVER TO ENGINE BOLTS.REMOVE 3 WATER PUMP TO TIMING CHAIN HOUSING NUTS.REMOVE THE WATER PUMP AND COVER ASSEMBLY.THE 3.1 AND 3.4 ENGINES DRAIN COOLING SYSTEM .REMOVE DRIVE BELT.REMOVE WATERPUMP PULLEY TO REMOVE PULLEY YOU NEED A LONG SKINNEY SCREW DRIVER TO HOLD PULLEY FROM TURNING WHILE YOU REMOVE THE BOLTS.THEN REMOVE WATER PUMP.CLEAN OLD GASKET MATERIAL OFF ENGINE BLOCK WHERE WATER PUMP GOES.BECAREFUL NOT TO SCRATCH PUMP SURFACE ON ENGINE BLOCK.YOU CAN BUY CAN OF GASKET REMOVER AT ANY AUTO PARTS STORES. THEN WHEN YOU PUT ON NEW WATER PUMP.BESURE TO COAT BOTH SIDES OF THE WATER PUMP GASKET WITH GASKET SEALER .BEFORE PUTTING GASKET SEALER ON WATER PUMP GASKET.BESURE TO GET HOLES MATCH UP RIGHT ON WATER PUMP AND GASKET.WHEN YOU GET IN PUMP IN PLACE TORQUE IT AT 89 INCH POUNDS AND PULLEY BOLTS 18 FT LBS.THE 2.4 ENGINE BEST TO HAVE** HAYNES REPAIR MANUAL ** BECAUSE REMOVING THE WATER PUMP YOU ARE DEALING WITH THE TIMING CHAIN AND TENSIONER.YOU NEED ALL THE EXHAUST BOLTS TORQUE SPECS.AND WHEN YOU COMPLETE WATER PUMP FIX.ADD COOLANT.CRANK ENGINE.CHECK FOR LEAKS.BLEED COOLANT SYSTEM.

Jun 14, 2010 | 1999 Pontiac Grand Am GT

1 Answer

WHERE THE WATER PUMP IS LOCATED on a 2.3 liter 4 cylinder quad hoc


it is driven off the timing chain, here is how you replace it
2.3L And 2.4L OHC Engines
  • Disconnect the oxygen sensor harness connector
  • Raise the vehicle and support it securely on jackstands
  • Remove the exhaust manifold brace and loosen the exhaust manifold bolts
  • Remove the radiator outlet pipe assembly to the water pump housing bolts and separate the assembly from the engine
  • Remove the exhaust manifold pipe from the exhaust manifold
  • Remove the radiator outlet pipe from the oil pan.On manual transaxles cars remove the exhaust manifold brace and keep the radiator inlet hose attached to the assembly.Pull down on the radiator outlet pipe in order to disengage the pipe from the water pump while leaving the radiator outlet pipe hanging
  • Lower the car remove the brake booster vacuum hose from the camshaft housing also remove the exhaust manifold from the cylinder head
  • Remove the timing chain cover from the engine
  • Remove the timing chain tensioner
  • Remove the water pump cover bolts from the engine block and the timing chain housing
  • Remove the water pump bolts and separate the assembly from the housing


Dec 01, 2009 | 1994 Pontiac Grand Am

2 Answers

Need the step by step instructions and pictures on how to replace an water pump on an 2002 Oldsmobile Alero 2.4L


Removal & Installation

2.2L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the engine coolant.
  4. Remove or disconnect the following:
    Exhaust manifold, if equipped with n automatic transaxle Right front wheel Splash shield Water pump sprocket access plate from the timing cover

    fcd00e0.jpg

    Fig. Remove the water pump sprocket access plate from the timing cover -2.2L engine
  5. Attach Water Pump Sprocket Holding Tool J 43651to the sprocket using the access plate bolts to secure the tool to the engine front cover.
    Sprocket to water pump bolts Engine block to water pump bolt Engine front cover to water pump bolt Thermostat housing to water pump feed pipe 2 water pump to engine block bolts Water pump

    30965cd.jpg

    Fig. Water pump mounting-2.2L engine
To install:
  1. Use a threaded stud in the water pump hub to align the hub to the water pump sprocket.
    Water pump and bolts Thermostat housing to water pump feed pipe Engine front cover bolt and engine block to water pump bolt. Tighten the bolts to 15 ft. lbs. (20 Nm) 2 of the water pump sprocket to water pump bolts
  2. Remove the threaded stud.
    Last water pump sprocket to water pump bolt and tighten the sprocket bolts to 89 inch lbs. (10 Nm).
  3. Remove the tool.
    Water pump sprocket access plate to the timing cover and tighten the bolts to 89 inch lbs. (10 Nm) Splash shield Right front wheel Exhaust manifold, if removed
  4. Fill the cooling system.
  5. Connect the negative battery cable.
2.4L Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    WARNING Do not rotate the flex coupling more than 4 degrees or damage may occur. Oxygen Sensor (O 2 S) electrical connector Exhaust manifold heat shield Coolant inlet housing bolt through the exhaust manifold Exhaust manifold brace-to-manifold bolt Manifold-to-exhaust pipe studs Coolant inlet housing-to-water pump cover bolt Exhaust pipe from the exhaust manifold by pulling it downward Coolant inlet pipe from the oil pan Brake vacuum pipe from the camshaft housing Exhaust manifold from the cylinder head Heater hose from the heater outlet pipe Timing chain cover and tensioner Water pump cover-to-engine bolts 3 water pump-to-timing chain housing nuts Water pump and cover assembly Water pump cover from the pump

    f9cdfa8.jpg

    Fig. Exploded view of the water pump mounting-2.4L engine
continue...

Oct 22, 2009 | 2002 Oldsmobile Alero

1 Answer

Replacing the water pump


2.4L Engine
  1. Disconnect the negative battery cable
  2. Detach the Oxygen (O2) sensor electrical connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for a more complete coolant drain.
  4. Remove upper exhaust manifold heat shield.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Remove the lower exhaust manifold heat shield.
  7. Break the manifold-to-exhaust pipe spring loaded bolts loose using a 13mm box wrench.
  8. Raise and safely support the vehicle.

NOTE It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  1. Unfasten the two radiator outlet pipe-to-water pump cover bolts.
  2. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.

NOTE DO NOT rotate the flex coupling more than 4° or damage may occur.
  1. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  2. Remove the radiator outlet pipe from the oil pan and transaxle. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump. Leave the radiator outlet pipe hang.
  3. Carefully lower the vehicle.
  4. Unfasten the exhaust manifold-to-cylinder head retaining nuts, then remove the exhaust manifold, seals and gaskets.
  5. Remove the front timing chain cover and the chain tensioner. For details, please refer to the procedure located later in this section.
  6. Unfasten the water pump-to-cylinder block bolts. Remove the water pump-to-timing chain housing nuts. Remove the water pump and cover mounting bolts and nuts. Remove the water pump and cover as an assembly, then separate the two pieces.
87953070.gif Water pump and cover mounting—2.4L engine
Click to Enlarge
To install:
  1. Thoroughly clean and dry all mounting surfaces, bolts and bolt holes. Using a new gasket, install the water pump to the cover and tighten the bolts finger-tight.
  2. Lubricate the splines of the water pump with clean grease and install the assembly to the engine using new gaskets. Install the mounting bolts and nuts finger-tight.
  3. Lubricate the radiator outlet pipe O-ring with antifreeze and slide the pipe onto the water pump cover. Install the bolts finger-tight.
  4. With all gaps closed, tighten the bolts, in the following sequence, to the proper values:
    1. Pump assembly-to-chain housing nuts:19 ft. lbs. (26 Nm).
    2. Pump cover-to-pump assembly: 106 inch lbs. (12 Nm).
    3. Cover-to-block, bottom bolt first: 19 ft. lbs. (26 Nm).
    4. Radiator outlet pipe assembly-to-pump cover: 125 inch lbs. (14 Nm).
  5. Using new gaskets, install the exhaust manifold. Make sure to following the tightening sequence and torque specifications given in the exhaust manifold procedure located in this section.
  6. Raise and safely support the vehicle.
  7. Index the exhaust manifold bolts into the exhaust pipe flange.
  8. Connect the exhaust pipe to the manifold. Install the exhaust pipe flange bolts evenly and gradually to avoid binding. Turn the bolts in until fully seated.
  9. Connect the radiator outlet pipe to the transaxle and oil pan.
  10. Install the timing chain tensioner and front cover.
  11. Install the lower heat shield.
  12. Carefully lower the vehicle.
  13. Fasten the bolt that attaches the exhaust manifold brace to the manifold.
  14. Tighten the manifold-to-exhaust pipe nuts to specification.
  15. Install the upper heat shield.
  16. Attach the oxygen sensor connector.
  17. Fill the radiator with coolant until it comes out the heater hose outlet at the thermostat housing. Then connect the heater hose. Leave the radiator cap off.
  18. Connect the negative battery cable, then start the engine. Run the vehicle until the thermostat opens, fill the radiator and recovery tank to their proper levels, then turn the engine OFF.
  19. Once the vehicle has cooled, recheck the coolant level, then install the radiator cap.

3.1L Engine
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Loosen, but do not remove, the water pump pulley bolts.
  4. Remove the serpentine belt.
  5. Unfasten the water pump pulley bolts, then remove the pulley.
  6. Remove the five water pump mounting bolts, then remove the water pump.
To install:
86883115.gif View of the water pump mounting and bolt tightening specifications—3.1L engine shown
Click to Enlarge
  1. Clean all the gasket surfaces completely.
  2. Apply a thin bead of sealer around the outside edge of the water pump along the gasket sealing area, then install the gasket onto the water pump.
  3. Position the water pump on the engine, then tighten the water pump mounting bolts to 89 inch lbs. (10 Nm).
  4. Install the water pump pulley and finger-tighten the pulley bolts.
  5. Install the serpentine belt.
  6. Tighten the water pump pulley bolts to 18 ft. lbs. (25 Nm).
  7. Fill the cooling system.
  8. Connect the negative battery cable, then start the engine. Let the engine run until it reaches normal operating temperature, then check for leaks and coolant level. Add coolant, if necessary, then turn the engine OFF.

Aug 20, 2009 | 1997 Chevrolet Malibu

Not finding what you are looking for?
2002 Ford Mustang Logo

Related Topics:

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5627 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...