Question about 2001 Audi A6

1 Answer

Assambly wiper system - 2001 Audi A6

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,874 Answers

First you must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows: 1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!! 2. Disassemble the plastic covers from the bottom of the windscreen. 3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables. 4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi. 5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters. 6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation! 7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!

Posted on Oct 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Pontiac Montana wipers not working how to fix


First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

Nov 25, 2016 | 2003 Pontiac Montana

1 Answer

Wipers in up position in off. 94 lincoln town car. How do the wipers return to rest position?


Do you know how to do electrical testing ?
PINPOINT TEST E: WINDSHIELD WIPERS WILL NOT PARK AT PROPER POSITION E1 CHECK WIPER MOTOR GROUND
  • Disconnect connector from windshield wiper motor.
  • Check continuity to ground at Circuit 57 (BK).
Is ground OK? Yes No GO to E2 . SERVICE open in Circuit 57 (BK). RESTORE vehicle. RETEST system. E2 CHECK FOR POWER AT WIPER MOTOR
  • Place ignition switch at RUN and multi-function switch at OFF.
  • Check for battery voltage between Pin 1, Circuit 65 (DG) and Pin 4, Circuit 57 (BK) at the windshield wiper motor connector.
Is B+ present? Yes No GO to E3 . SERVICE open circuits. RESTORE vehicle. RETEST system. E3 CHECK MOTOR CIRCUIT CONTINUITY THROUGH WINDSHIELD WIPER CONTROL MODULE
  • With multi-function switch at OFF, check continuity between Circuit 28 (BK/PK) and 56 (DB/O) and between Circuits 61 (Y/R) and 63 (R).
Is continuity OK? Yes No GO to E5 . GO to E4 . E4 CHECK CIRCUITS TO WIPER CONTROL MODULE
  • Disconnect wiper control module connector.
  • Check continuity of Circuits according to the chart below from the wiper motor to the wiper control module.

    Wiper Control Module Connector Wiper Motor Connector Pin Circuit Pin 6 Pin 2 28 (BK/PK) Pin 8 Pin 6 56 (DB/O) Pin 12 Pin 5 61 (Y/R) Pin 13 Pin 3 63 (R)
Is continuity present? Yes No REPLACE wiper control module. RESTORE vehicle. RETEST system. SERVICE open circuits. RESTORE vehicle. RETEST system. E5 CHECK WIPER MOUNTING ARM/PIVOT SHAFT
  • Check that windshield wiper mounting arm and pivot shaft and linkage is not bent, cracked or mis-positioned.
Is windshield wiper mounting arm and pivot shaft linkage OK? Yes No REPLACE windshield wiper motor. RESTORE vehicle. RETEST system.

Nov 14, 2016 | 1994 Lincoln Town Car

1 Answer

Cadillac Deville 99


Wiper/Washer System (Pulse) Schematics (w/o CE1)
Wiper/Washer System (Pulse) Schematics (w/CE1)

Which one does yours have ?

The switch could be bad or the windshield wiper / washer module . Do you own a DVOM - digital volt ohm meter ? Do you know how to do automotive electrical trouble shooting ? There are a few good videos on youtube on basic electrical trouble shooting an how to read wiring diagrams . Go to http://www.bbbind.com/free_tsb.html for free wiring diagrams . Check B+ voltage at the switch (in an out ) at the different speeds .Check for B+ voltage at the wiper washer module , it's part of the wiper motor .
The windshield wiper/washer system consists of a permanent-magnet depressed-park wiper motor assembly, a wiper transmission assembly, wiper arm and blade assemblies, a washer pump mounted on a washer solvent container, and a wiper/washer switch assembly.
The wiper/washer system is a pulse (delay) type. Pulse timing and demand wash functions are controlled electronically. Wiper/Washer System Description (Rainsense)
The windshield wiper/washer system consists of a Rainsense module, a permanent-magnet, depressed-park wiper motor assembly, a wiper transmission, wiper arm and blade assemblies, a washer pump mounted on a washer solvent reservoir, and a wiper/washer switch assembly.
The wiper/washer system is a rain sensing type. Rainsense functions are controlled electronically. 1
Was the Wiper/Washer System Check performed?
--
Go to Step 2
Go to Wiper/Washer System Check

2
Inspect the WIPERS fuse A9 for an open.
Is the fuse open?
--
YES - Go to Step 3
NO - Go to Step 4

3
Replace the WIPERS fuse.
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

4
Disconnect the wiper/washer switch connector C202.
Turn ignition switch ON.
Connect a test light from connector C202, terminal E5 to ground.
Is the test light on?
--
YES - Go to Step 16
NO - Go to Step 5

5
Connect a test light from Accessory Relay, terminal A1, to ground.
Is the test light on?
--
YES - Go to Step 6
NO - Go to Step 11

6
Connect a test light from Accessory Relay, terminal A3, to ground.
Is the test light on?
--
YES - Go to Step 7
NO - Go to Step 12

7
Connect a test light from Accessory Relay, terminal B1 to terminal A3.
Is the test light on?
--
YES - Go to Step 8
NO - Go to Step 15

8
Inspect CKT 143 for an open or poor connection between connector C202 and the Accessory Relay.
Was an open or poor connection found?
--
YES - Go to Step 9
NO - Go to Step 10

9
Repair the open or poor connection in CKT 143.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

10
Replace the the Accessory Relay.
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

11
Repair the open in CKT 1040 or the power feed circuit to the WIPERS fuse.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

12
Inspect the ACC fuse C13 for an open.

let me know if you make it this far an then I will send the rest of testing procedures !

Mar 09, 2016 | Cadillac DeVille Cars & Trucks

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

1 Answer

Replace right front turn signal bulb


you'll need a 10mm socket and a 1/4 in drive rachet, look around headlight assamble you have to remove 3 hex head screws 2 will be in front of head light 1 above and 1 below, then the 3rd will be in the lower corner next to turn signal light ,once you remove all bolts there is a rubber strip around headlight on edge of grill very carefully remove the three black molding buttons ,next you'll have to pull outwards on assamble till you feel it release then carefully reach around back of headlight assamble and turn bulb housing to left and remove bulb and replace ,reassemble in reverse making sure you you line up mounting post before pushing it back in ,it may take some force to set it back in, PS . check to make sure it works before you put it all back in. good luck .
I hope this helps you if it did please let me know by clicking on helpful -yes .thank you .
Woody

Sep 27, 2014 | 1996 Dodge Dakota

1 Answer

Wipers stop in the middle of my wishield,will not park properly


Sorry , no adjustment .
Wiper/Washer System Components
The Wiper / Washer System consists of the following components:
• Windshield wiper / washer switch
• Windshield wiper system module / motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR 25A fuse
Wiper / Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls the wiper motor operation. The windshield wiper motor is a 2 speed motor. Windshield wiper DELAY operation is a low speed wiper motor function with a variable delay interval between the wipe cycles. The DELAY interval is controlled through a series of resistors within the wiper / washer switch.
Park Position Operation
When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Do you know how to do diagnostic's ?

Wipers Blades Do Not Park
Step
Action
Yes
No
Schematic Reference: Wiper/Washer Schematics
Connector End View Reference: Wiper/Washer Connector End Views
DEFINITION: This table diagnoses the wipers operate normally but will not return to the park position when the wiper operation is cancelled.
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Turn ON the ignition, with the engine OFF.
Move the wiper switch to the LO position.
Move the wiper switch to the OFF position.
Do the front wipers advance to the park position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn the ignition switch to the RUN position.
Turn the wiper switch to OFF.
Disconnect the wiper/washer switch connector.
Do the wipers park?
YES - Go to Step 7
NO - Go to Step 4
4
At the wiper/washer switch connector, measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 5
NO - Go to Step 8
5
Reconnect the wiper/washer switch connector.
Disconnect the wiper motor connector.
Measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 6
NO - Go to Step 8
6
Repair a short to battery positive voltage in the windshield wiper switch signal 2 circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
YES - Did you find and correct the condition?
NO - Go to Step 9
--
7
Replace the wiper/washer switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column - Tilt.
YES - Did you complete the replacement?
NO - Go to Step 9
--
8
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
YES - Did you complete the replacement?
NO - Go to Step 9
--
9
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jan 31, 2018 | 2005 Buick Century

1 Answer

Winsheild wiper will not work


The wiper control module is probably at fault ,without test that is just a guess . The wiper/washer switch is a input to the wiper control module. Do you know anything about automotive electronics an electrical systems ?
  • The Wipers are Inoperative
  • Fuse.
  • Wiper motor.
  • Multi-function switch.
  • Circuitry.
  • Wiper control module.
  • GO to Pinpoint Test B .

Voltage drop testing the power an ground circuits for the wiper control module would be a good place to start . Do you know how to test electrical circuits with a volt meter ?
PINPOINT TEST B: THE WIPERS ARE INOPERATIVE CONDITIONS DETAILS/RESULTS/ACTIONS B1 CHECK FUSE JUNCTION PANEL FUSE 16 (30A)
Fuse 16 (30A)

  • Is the fuse OK?
Yes GO to B2 .

No REPLACE the fuse. TEST the system for normal operation. If the fuse fails again, CHECK for a short to ground. REPAIR as necessary. B2 CHECK FOR VOLTAGE TO THE WIPER CONTROL MODULE - CIRCUIT 65 (DG)
Wiper Control Module C294
Measure the voltage between wiper control module C294-2, circuit 65 (DG), and ground; and between wiper control module C294-11, circuit 65 (DG), and ground.
  • Is the voltage greater than 10 volts?
Yes GO to B3 .

No REPAIR circuit 65 (DG). TEST the system for normal operation. B3 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper control module C294-3, circuit 57 (BK), and ground; and between wiper control module C294-5, circuit 57 (BK), and ground.
  • Are the resistances less than 5 ohms?
Yes GO to B4 .

No REPAIR circuit 57 (BK). TEST the system for normal operation. B4 CHECK THE MULTI-FUNCTION SWITCH
Multi-Function Switch
Check the multi-function switch; refer to Section 211-05 .
  • Is the multi-function switch OK?
Yes GO to B5 .

No REPLACE the multi-function switch; REFER to Section 211-05 . TEST the system for normal operation. B5 CHECK CIRCUIT 993 (BR/W) FOR OPEN Measure the resistance between multi-function switch C269-4, circuit 993 (BR/W), and wiper control module C294-7, circuit 993 (BR/W).
  • Is the resistance less than 5 ohms?
Yes GO to B6 .

No REPAIR circuit 993 (BR/W). TEST the system for normal operation. B6 CHECK CIRCUIT 589 (O) FOR OPEN Measure the resistance between multi-function switch C269-1, circuit 589 (O), and wiper control module C294-1, circuit 589 (O).
  • Is the resistance less than 5 ohms?
Yes GO to B7 .

No REPAIR circuit 589 (O). TEST the system for normal operation. B7 CHECK THE WIPER CONTROL MODULE OUTPUT FOR VOLTAGE
Wiper Control Module C294

Wiper Motor C152
Turn the multi-function switch to the HI position. Measure the voltage between wiper motor C152-4, circuit 57 (BK), and wiper motor C152-3, circuit 56 (DB/O).
  • Is the voltage greater than 10 volts?
Yes REPLACE the wiper motor; REFER to Motor-Windshield Wiper . TEST the system for normal operation.

No GO to B8 . B8 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper motor C152-4, circuit 57 (BK), and ground.
  • Is the resistance less than 5 ohms?
Yes REPLACE the wiper control module; REFER to Module-Windshield Wiper . TEST the system for normal operation.

No REPAIR circuit 57 (BK). TEST the system for normal operation.

Jun 29, 2017 | 2002 Lincoln Town Car

1 Answer

How do I remove the front headlight to replace the bulb


there are two 7mm long bolts on top of headlamp assambly of course need to open hood to be able to see them and have to be carefull when removing and installling headlamp assambly

Nov 17, 2009 | 2002 Chrysler Concorde

Not finding what you are looking for?
2001 Audi A6 Logo

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

80417 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...