Question about 1999 Ford Crown Victoria

Open Question

Crown vic wont go in reverse - 1999 Ford Crown Victoria

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 1992 crown vic 4.6l

did you check the inertia switch?? that's what happened to mine

Posted on Aug 13, 2008

Ad
chrischronic
  • 235 Answers

SOURCE: 1995 crown vic gear problems/gear shift wont lock

if the shifter is loose and sloppy feeling then the shift cable bracket has come loose under the dash at the steering wheel. remove the lower panel under the steering wheel so you can see under the dash then get flash light and look while jiggling the shifter. you should be able to see the cable and bracket. if the bracket is loose then tighten the bolts. note this bracket is at the steering colum.

Posted on Jan 22, 2009

  • 5520 Answers

SOURCE: Wiper motor replacement for a 99 crown vic

I replaced the same part on a 1994 Crown Vic. There are a few bolts which go through rubber mounts on the firewall and that is how the wiper motor fits against the firewall. There is a clip on the wiper drive that must be pressed and slid off the wiper shaft. The hardest part was getting clearence between the engine and wiper motor. If I remember there was a way to turn the wiper case to clear the engine. I have asked myself why this was engineered like this? There is nothing important in the way that 3/4" of clearance could have been given for removal.

Posted on May 06, 2009

jaysonemanme
  • 500 Answers

SOURCE: 1995 crown vic gear problems/gear shift wont lock

most likely the shift tube bushings are bad- you may have also lost a few screws in the shift tube or they could just be loose. you have to pull the steernig column down to inspect/repair it.

Posted on May 31, 2009

  • 33 Answers

SOURCE: Replace horn on 2006 crown vic

I believe once you have mounted the horn and connected the wire you will find that the horn wire was cut at (by) the steering coloum that the siren override was hooked to,you will have reconnect this,I hope this helps you

Posted on Jul 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 crown vic and the problem that I'm


Please check with your local body shop.

Aug 29, 2013 | Cars & Trucks

1 Answer

How to replace a heater valve of a 2002 crown vic?


Heater valve or core? Heater control valve is as simple as loosening clamps and pulling hoses off. Reverse to install. Fill with anti-freeze.

Dec 18, 2010 | 2001 Ford Crown Victoria

1 Answer

How do I change a window switch on a crown vic


Lift up on the front of the window switch panel. itwill snap out. Disconect the electrical connectors. relese the 4 locking tabs and remove the switch. Reverse proeadure to install.

Jun 17, 2010 | 2006 Ford Crown Victoria

1 Answer

Crown Vic wont turn over.


I would check the plugs around and on the engine. Also check to see if the inertia switch in the trunk was tripped, that cuts off power to the fuel pump in an accident.

May 11, 2010 | 1984 Ford Crown Victoria

1 Answer

Ford crown victoria


you must replace the multi fuction switch! also known as the turn signal switch! its common on ford crown vic!

Mar 06, 2010 | 2001 Ford Crown Victoria

1 Answer

1995 crown vic gear problems/gear shift wont lock


most likely the shift tube bushings are bad- you may have also lost a few screws in the shift tube or they could just be loose. you have to pull the steernig column down to inspect/repair it.

May 30, 2009 | 1995 Ford Crown Victoria

3 Answers

1992 Crown Vic wont crank


Check the starter solenoid. Usually mounted on a fender well. Find by following the + battery cable.

Feb 14, 2009 | 1992 Ford Crown Victoria

1 Answer

1995 crown vic gear problems/gear shift wont lock


if the shifter is loose and sloppy feeling then the shift cable bracket has come loose under the dash at the steering wheel. remove the lower panel under the steering wheel so you can see under the dash then get flash light and look while jiggling the shifter. you should be able to see the cable and bracket. if the bracket is loose then tighten the bolts. note this bracket is at the steering colum.

Jan 21, 2009 | 1995 Ford Crown Victoria

2 Answers

1992 crown vic 4.6l


did you check the inertia switch?? that's what happened to mine

Jul 25, 2008 | 1992 Ford Crown Victoria

Not finding what you are looking for?
1999 Ford Crown Victoria Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...