Question about 2005 Nissan Altima

1 Answer

I have a torn upper motor mount on my 2005 Nissan Altima. What is replacement procedure ?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Nissan Master
  • 14,036 Answers


Posted on Oct 10, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2005 Nissan Altima jerks on Drive or Reverse for a second when hot.

Check for loss engine motor mounts and transmission mount
Also check the air tube (TOP AND BOTTOM) for hairline crack.

A loss motor mount can cause excessive vibration and damage the air inlet tube.

Jan 15, 2014 | Cars & Trucks

1 Answer

How can i change the throttle body for a 2002 nissan altima 3.5

replacement is simple 4 bolts and an electrical connector.tricky part is performing idle air volume learn procedure which MUST be done after my knowledge dealer only procedure.not sure if aftermarket diagnostic equipment supports this procedure.

Jan 16, 2011 | 2005 Nissan Altima

1 Answer

Rattling / grinding sound coming from engine area when vehicle is in gear and car break is applied, but when gear is set into neutral noise stops. Was told the problem was the aircondition compressor....

Just a couple ideas...
Your engine and transmission will shift slightly when in drive, and maybe that movement is allowing it to rub on something. Another issue may be that the noise is actually from the transmission.
Torn motor mounts will allow the drive train to shift or move farther than normal.

Jul 07, 2010 | 2003 Nissan Altima

2 Answers

How do I replace the coolant temperature sensor on a 1996 nissan altima?

If you look on the front of your upper water hose going from motor toraditor, you will see a small wire and plug assy. that will be the sensor and just unscrew and replace. Good luck it is quite easy to do.
Emmett Sr.

Jun 21, 2010 | 1996 Nissan Altima

1 Answer

2005 Nissan Altima where is blower motor resistor is located and what does it look like

The blower motor resistor is mounted under the glove box. It is in the corner somewhat covered by the kick panel. The card, at least on my pathfinder, is held in with 2 phillips head screws. The plug has 4 wires, one large wire and 3 smaller wires. You should see it very near to and parallel with the firewall.

May 17, 2010 | 2005 Nissan Altima

1 Answer

How to remove , replace , a upper idler arm pulley on a 1999 nissan altima. looks like the bolt came out is rubbing on wheel well who do ya get it out not a whole lot of space in there !!!!

thats a fun one

first jack up the car then remove the engine mount remember to suport the motor slowely lower motor untill it alows axcess the pulley

best bet is mechanic

Jan 16, 2010 | 1999 Nissan Altima

1 Answer

How do you repain the upper engine mount

prop engine from under the car and remove and replace engine mount

Dec 22, 2009 | 2005 Nissan Altima

Not finding what you are looking for?
2005 Nissan Altima Logo

Related Topics:

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

76682 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides