Question about 2000 Oldsmobile Bravada

1 Answer

How to remove front spindle nut on a 2000 Oldsmobile Bravada

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 300 Answers

The 2000 Oldsmobile Bravada spindle nut is 36mm, and the Torque specification is 203 ft-lb.
To remove the nut you need a very powerful impact drive, or 1 inch drive socket tool.

Posted on Oct 10, 2010

  • angelsand456 Aug 28, 2011

    where can i buy a used left front spindle - 2000 olds bravada all wheel drive suv

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i bleed heater


1997 Oldsmobile Bravada heater core removal - YouTube

? 3:22
www.youtube.com/watch?v=7OwIuiYqt0s

Oct 25, 2012 - Uploaded by Lloyd Ankney
1997 Oldsmobile Bravada heater core removal ... How can I replace a blend door actuator on a 99 Bravada? .... Heater core replacement 2000 S10 4.3L ( slideshow picture ) - Duration: 3:52. by Joe Lleras 169,585 views. 3:52.

Oldsmobile bleed air in heater core Cars & Trucks ... - Fixya

www.fixya.com > Forum > Tags > bleed air in heater core > Cars & Trucks
If your cooling system has any bleed screws incorporated, crack them once in a while as well. 2000 Oldsmobile Bravada heater blows cold air. Had a new heater .

Oct 25, 2015 | 2000 Oldsmobile Bravada

1 Answer

Humming noise coming from vehicle over 30mph


At 100,000 miles, you are driving on bad wheel bearings. They are not too bad to replace, it is a wheel bearing assembly. Bolts on . You will need to remove the spindle nuts, the brakes and rotors, and unplug your abs cable from under the hood. It should take about 1 hour per side if you haven't done it before, and the bearings should be around $120.00 each.

Sep 14, 2014 | 2003 Oldsmobile Bravada

1 Answer

2000 Oldsmobile Bravada torque specs


what do you need the specs for? head bolts? lug nuts? steering wheel????

May 29, 2011 | 2000 Oldsmobile Bravada

1 Answer

How to remove the right side axel shaft on a 98 olds bravada


1. Raise and support vehicle, then remove tire and wheel assembly. 2. Install a brass drift or a screwdriver to prevent the rotor from turning, Fig. 7 . 3. Remove axle nut and washer. 4. Remove stabilizer shaft or link from control arm. 5. Remove nut from ball joint, then separate ball joint from steering knuckle using separator tool No. J-36226, or equivalent. 6. Remove drive axle from hub and bearing assembly using front hub spindle remover tool No. J-28733-A, or equivalent, Fig. 8 . 7. Remove drive axle from transaxle using axle shaft remover puller tool Nos. J-33008, J-29794 and slide hammer tool No. J-2619-01, or equivalents, if necessary, Fig. 9 . INSTALLATION 1. Install drive axle into the transaxle using seal protector J-37292-B, or equivalent 2. Seat snap ring by placing a screwdriver into the groove on the joint housing and tapping until seated, Fig. 9 . 3. Grasp the inner housing and pull outward. If the snap ring is properly seated, the axle will remain in place. 4. Install drive axle into hub and bearing assembly. 5. Install lower ball joint to steering knuckle and tighten to specifications. 6. Install stabilizer shaft or link to control arm, tighten to specifications. 7. Insert a screwdriver or drift into caliper and rotor to prevent rotor from turning, Fig. 7 . 8. Install new hub nut and washer, tighten to specification. 9. Install tire and wheel assembly, then lower vehicle

Feb 13, 2011 | 1998 Oldsmobile Bravada

2 Answers

Will rims off my 99 wrangler fit on my 2000 olds bravada?


Take a tape measure and measure from the center of one hole in the rim to the one next to it. write that measurement down. Now measure from the center of one of your lug nuts on your bravada to the center of the lug nut next to it. If the measurements match exactly, the rims should fit.

Oct 09, 2010 | Oldsmobile Bravada Cars & Trucks

1 Answer

Low power and missfire, have replaced bad distributor and rotor. 2000 Oldsmobile Bravada AWD. Where are the fuel pump and filter located?


I have replaced Distributor cap, rotor, wires, and spark plugs in my 2000 Oldsmobile Bravada AWD smart track. To replace one spark plug I had to collapse the steering column, but everything went O.K. Did you marked the wires?. Did you reconnect them in the firing order?
The fuel pump is located In the fuel tank. Remove the fuel tank and take the fuel pump out from the top. This is part cost $300 and need some skills to be replaced.
The fuel filter it is directly in front of the fuel tank. Another one is incorporated with the fuel pump.

Sep 10, 2010 | 2000 Oldsmobile Bravada

1 Answer

2000 OLDS BRAVADA FIRING ORDER DIAGRAM , WE CHANGED PRESSURE REGULATOR, NOW TRUCK FEELS AS IF ITS MISFIRING. WE ONLY REMOVED THE 3 SPARK PLUG WIRES ON THE RIGHT SIDE OF VEHICLE, IF LOOKING FROM THE FRONT.


For the Oldsmobile Bravada 4.3L V6:

Firing Order
:
1-6-5-4-3-2

Cylinders:
......(back)......
|..6..|.......|..5..|
|..4..|.......|..3..|
|..2..|.......|..1..|
......(front)

Distributor Connections:
...........(back)
Coil-> o
6-----> o.......o <-----5
4-----> o.......o <-----1
2-----> o.......o <-----3
...........(front)

Let me now if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Apr 25, 2010 | 2000 Oldsmobile Bravada

1 Answer

Need infor for Oldsmobile Bravada 300 SUV R&R front differential


This is a HUGE job that will require mechanical skills and a goo repair manual. This question can not be answered in it's entirety in this post.

Jan 16, 2010 | 2000 Oldsmobile Bravada

1 Answer

Removal of 2000 bravada fuel filter


On frame under driver seat area. Must have high quality flare nut wrench for one side, and just press plastic release clips on other. Be Careful with gas coming out!!! When puttng new filter on, move plastic clip into fuel line fitting first before trying to press on. Bad fuel pumps are common on these vehicles, try "thepartsladi" store on eBay for low cost OEM replacement parts.

Nov 18, 2009 | 2000 Oldsmobile Bravada

Not finding what you are looking for?
2000 Oldsmobile Bravada Logo

Related Topics:

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...