Question about 2002 Mercury Villager

1 Answer

Have a vaccum line that is off and can not find where it connects, where can i find a free vaccum diagram? the lin that is loose is coming from the transmission.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

It may be just the vent tube for the trans. metal u shaped end?

go here

Posted on Oct 20, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Vaccum line routing

Are you sure that it is not a vent line? Most gear cases are vented.

Apr 02, 2014 | 1993 Jeep Cherokee Country

1 Answer

I have a 1985 Nisson 720 standard bed pickup. The engine cranks over but is hard fireing. When it does fire up, it runs fine until I let off the gas and then it stalls. I've checked all the vacuum lin

This is what I would do. Start with adjusting the idle speed screw til the motor runs without holding the gas pedal. With a timing light adjust the timing to the specifications back idle speed to about 750 rpm. This is the tricky part connect a vacuum guage to a manifold vaccum. If the timing is right the guage should be around 16to18 inches of vaccum. Turn the mixture screw in til the engine starts to stumble then turn screw out til the vaccum guage reaches its highest reading. The vacuum readings will drop off if you go to far out so going back and forth 1 full turn is common. I usually go to the maximum vaccum then half of a turn in. Mark one end of the screw slot to give you a reference to be able to count the number of turns. All these adjustments are done with the engine at operating tempature vaccum advance disconnected vaccum line plugged unless specified by the manufacturer. It's on the sticker under the hood.

Feb 01, 2014 | Cars & Trucks

1 Answer

Vacuum hose routing diagram

It goes to the Pvc system. Usually onto a valve cover

Aug 06, 2013 | 1995 Mercury Mystique

2 Answers

I need tom locate a vacuum line diagram for a 1981 chevy monte carlo 2269 v6 motor with a dual jet 210 electonic feedback carburater

Please choose the correct diagram. If you nhave problems viewing it, please post your email address. Diagram is free, no strings attached. It is just too large when trying to post it full size.

1981 229 (3.8L) V6 engine-automatic transmission

1981 229 (3.8L) V6 engine-automatic transmission alternate

1981 231 (3.8L) V6 turbo engine-automatic transmission

Aug 12, 2010 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

1987 pontiac fiero won't shift out of first gear automatic transmission. engine was just put back together from pieces. vacuume lines are hanging out don't know where to connect.

heres a vaccum diagram and alao make sure the passing gear cable is connect and adjusted if this car has one which i think it does, also check electrical connections are hooked up,heres two diagrams i labeled them, one is for the 2.5 engine and the other for 2.8 engine connect the vaccum line and retry it, hope this helps.d09847a.gifc3e18c5.gif

Apr 28, 2010 | 1987 Pontiac Fiero

2 Answers

I need a vaccum line diagram for a 4.3 liter the whole under the hood vaccum diagram for a 1998 s10 4.3

Below a link to the diagram you requested for a 1998 S-10 with a 4.3. Please feel free to post back with any questions. Best of luck.

Chevy S-10 Vacuum Diagram

Jul 22, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

A/C coming out of defroster and will not go to any other settings

It is a loose vacuum line, and you'll just have to trace it by hand as to where it needs to go. You might be lucky and have a vacuum line diagram under the hood, or you could buy a Haynes or Chilton's manual for the diagram. Vacuum is what controls the dampers in the air box(s), and with that line being loose you aren't getting sufficient vacuum to move them.

May 27, 2009 | 1999 GMC Safari

2 Answers

Correct vaccum line hook ups for 91 toyota pickup 6 cyc

You will find what your looking for here. free and with real pictures!!! got a few you can check out but use the first one first
these will help you a lot, they helped me out with the same problem

Apr 17, 2009 | Toyota Pickup Cars & Trucks

1 Answer

Vaccum line diagram for a 1988 honda accord

There is a Vaccum diagram in that manuel.
make sure you are looking at the correct engine diagram
You mostlikely have the A20A3 or A4 that is the diagrams you should be looking at.
Good luck.

Oct 03, 2008 | 1988 Honda Accord 4 Door

Not finding what you are looking for?
2002 Mercury Villager Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

76164 Answers


Level 3 Expert

5522 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides