Question about 2001 Mercury Grand Marquis

1 Answer

Neither power mirror will move with the switch and must be adjusted by hand

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Did you try locating the fuse for them should be marked power mirrors

Posted on Oct 10, 2010

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: replaced the power mirror switch on my 99

its the switch the remote part is bad the pad that you roll around is no good replace it

Posted on May 05, 2009

czaa
  • 4536 Answers

SOURCE: dodge sprinter the auto switch to move the mirrors

u can but it may not be worth all the trouble-sometimes u hurt other things for somethin minor-sec 629 inthe library has repair books

Posted on Aug 09, 2009

  • 224 Answers

SOURCE: Drivers side power mirror will not move except

you have to remove door panel

Posted on Nov 13, 2009

  • 474 Answers

SOURCE: on my 95 honda accord

Use contact cleaner and clean the contacs on the switch. They are probably black with carbon buildup or dirt.

Posted on Feb 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 chevy malibu dome light not working cant find the right fuse and power mirrors not working either


Dome light runs off the interior fuse. Dash, radio and others also. If the work, could be a bad bulb, switch or wire. Mirrors power comes from the master switch. Could be the mirror switch or mirror motors. If both quit working at the same time, look to the switch. If they died separately, After time. Replace the mirror assembly if you want them to work. They can be adjusted by hand.Push on the mirror.

Jan 12, 2017 | 2001 Chevrolet Malibu

1 Answer

Power exterior mirrors jammed


The could be broken. But if they click when trying to move them. Push on the mirror and center it. It will click when pushing it. Then try the switch. They do adjust by hand if the switch or motor goes bad.

Dec 21, 2016 | Cars & Trucks

2 Answers

Drive side mirror not working


Probably the switch I have seen many stop working and maybe one mirror stop out of hundreds

Apr 07, 2015 | 2003 Nissan 350Z

1 Answer

How to retract exterior mirrors


If power operated use mirror adjustment switch. Turn and point knob arrow down toward mirror icon. If not power pull them in by hand with a little force.

Mar 01, 2015 | 2014 Audi A4

1 Answer

Memory seats adjust on there own as well as mirrors


BCM has nothing to do with this function , MMM - memory mirror module !
Memory Mirror System Operation
The MMM is capable of storing mirror position for 2 different drivers. Mirror position is determined by both horizontal and vertical position sensors in each of the power mirrors. The MMM supplies a reference voltage and a low reference to these sensors and determines mirror position through the horizontal and vertical position signal circuits.
The MMM receives power through the battery supply voltage circuit and the MIR/LOCK fuse and a constant ground source. Any time that battery voltage is disconnected and then connected from the MMM, the MMM will enter the mirror relearn mode. The mirror relearn mode can also be commanded using a scan tool. Refer to Memory Mirror Module Learn for further information.The memory switch receives power through the battery supply voltage circuit and the MIR/LOCK fuse. The MMM upon receipt of a memory switch signal input, a class 2 message from the SIC or a class 2 message from the PCM indicating that the transmission is in park, will then supply battery voltage and ground to the appropriate power mirror motors through the mirror motor control circuits to move the mirrors to the predetermined positions.

DTC B1586, B1596, B1616, or B1626
The mirror horizontal and vertical position sensors are potentiometers. The Memory Mirror Module (MMM) provides these sensors with a 5 volt reference circuit and a low reference circuit. The MMM monitors the horizontal and vertical position sensor signal circuits which change values based on mirror position. These voltage values are used to determine mirror position and can be set into memory. When the MMM receives a memory recall request, the MMM will control the power mirror to the memory position based on the horizontal and vertical position sensor signal values.

Install a scan tool.
Turn ON the ignition, with the engine OFF.
With the scan tool, observe the mirror horizontal and vertical position parameters in the Memory Mirror Module (MMM) data list.
Operate both the left and right mirrors through the full range of movements.
Does the scan tool indicate that the left and right mirror horizontal and vertical position parameters are within the specified range?

Memory Seat System Components
The memory seat system consists of the following components:
• Power seat switch assembly
• Memory recall switch assembly
• Horizontal adjuster motor
• Front vertical adjuster motor
• Rear vertical adjuster motor
• Recline adjuster motor
• Memory seat module
• Memory mirror module
• SEAT 25A circuit breaker
• MIR/LOCK 3A fuse

Your best bet , take it to a qualified repair shop !

May 23, 2017 | 2002 Cadillac Escalade

1 Answer

My right mirror on 325 i 2005 doesn't work. When i change my seat position with the memory, the seats goes on but not the mirrors. I can adjust my left mirror but not the rigth one; it never move.


I would safely assume your right mirror may be inoperable period then by your statement you are leaving the switch for the mirrors in the middle during switching correct and during adjustment are switching to R/L mirror on the switch? Mirrors are on the same circuit so both should be operable. Have the mirror checked for operation before heading any further. I Think you will find during this its unplugged from its source of power or inoperable period and needs replaced. Remember to rate my solution and leave testimonial PS please purchase you a Owners Manual for your car you will thank me later.

Oct 09, 2012 | 2005 BMW 325i Automatic

1 Answer

Drivers side mirror doesn't work when I try to adjust with switch passenger side does


Try moving the mirror by hand at first incase the motor is stuck and then try with the switch. If that doesn't work, then either you have a loose connector or the motor went bad and needs to be replaced.
Benjamin

Aug 22, 2010 | 2006 Dodge Grand Caravan

1 Answer

Dodge sprinter the auto switch to move the mirrors works on the drivers side mirrors but the passenger mirror won't move...i think someone manually adjusted them by hand...can i fix this?


u can but it may not be worth all the trouble-sometimes u hurt other things for somethin minor-sec 629 inthe library has repair books

Aug 09, 2009 | 2006 Dodge Sprinter

Not finding what you are looking for?
2001 Mercury Grand Marquis Logo

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

fordexpert

Level 3 Expert

5626 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...