Question about 1997 Infiniti.5 Q45

Open Question

How can I program the garage door opener for my 1997 Infinity Q45

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 118 Answers

SOURCE: jag xj6 1996 97 programming the garage door openers

1. For first time training, press and hold the two outer HomeLink buttons, releasing only when the HomeLink indicator light begins to flash after 20 seconds. (Do not perform this step when training the additional HomeLink buttons.) 2. Position the hand-held transmitter 1-3 inches away from the HomeLink surface (located on your visor), keeping the HomeLink indicator light in view.
3. Using both hands, simultaneously press and hold both the desired HomeLink button and hand held transmitter button. DO NOT release until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. (The rapid flashing indicates successful training.)
property_damage_symbol_sm.gif Note: Some garage door openers may require you to replace step 3 with the “cycling” procedure noted in the “View Canadian Instructions” section.
4. Press and hold the trained HomeLink button and observe the indicator light.

  • If the indicator light is solid/continuous, training is complete and your device should activate when the HomeLink button is pressed and released.
  • If the indicator light blinks rapidly for 2 seconds and then turns a solid/continuous light, proceed with the following training instructions for a rolling code device. A second person may make the following steps quicker and easier. Please use a ladder or other device. Do not stand on your vehicle to perform the next steps.
5. At the garage door opener receiver (motorhead unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). If there is difficulty locating the training button, reference the garage door opener’s manual or contact us. 6. Press and release the “learn” or “smart” button (the name and color of the button may vary by manufacturer). NOTE: Once the button is pressed, there are 30 seconds in which to initiate the next step. 7. Return to the vehicle and firmly press and hold the trained HomeLink button for two seconds and release. Repeat the “press/hold/release” sequence up to 3 times to complete the training process.

Posted on Jan 30, 2009

motor1258
  • 6674 Answers

SOURCE: 1999 Infinity QX4. Door Open warning light

usually on post where door closes, or in jamb by hinge area. Open door & try pushing any button/pin like object or may be a lever style too, with thumb or finger.When interior light goes out, you found it

Posted on May 03, 2009

  • 1 Answer

SOURCE: Garage door opener - homelink system - will not program

I couldn't program the first one, but I was able to program the 2nd button. I programmed it from the main system and not the remote. I also had a hard time programming remote to homelink.

Posted on May 07, 2009

  • 4 Answers

SOURCE: program instruction garage door opener in 2005 chrysler pacifica

You can download the operators manual for free at chrysler.com. It has the instructions to program the garage door opener. It's fairly easy with the instructions.

Good Luck,
Ray

Posted on May 11, 2009

  • 1348 Answers

SOURCE: programming garage door opener

there are three buttons on the opener.hold the 2 outside ones down for 25 to 30 seconds to erase the program. once the light (if equipped)flash rate changes,let go.
then push any one of the the three buttons and hold it in. and then push your remote. when the flash rate changes,the code is now in the homelink transmitter.the slt and slt plus had that feature.

Posted on May 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1997 Infinity Q45 and the heat will not cut off and I changed the off button


Its not the mother board, most likely its the thermostat. Did they replace it?

Mar 17, 2014 | Cars & Trucks

1 Answer

Repaced bcm to fix the power door locks and windows bu now sunroof doesnt work. 1999 q45 infinity.


You most likely need to have the new BCM programmed so it recognizes the sun roof option. This is a dealer only job.

Nov 06, 2013 | Cars & Trucks

1 Answer

Repairing the light on the analog clock of a 2002 infinity Q45


repairing the light on the analog clock of a 2002 infinity Q45
i want ti know which model should i buy (bulbs burned)

Jan 15, 2011 | 2004 Infiniti Q45

1 Answer

There are 3 buttons on the sun driver side visor, what do they do? when I push any of the, a light lites next to it?


these should be programable buttons for a garage door opener setup in your car...they can be set to the frequency of a garage door remote....

Jan 11, 2011 | 1997 Jeep Grand Cherokee

1 Answer

No lights working on dash and console of my 1997 infinity q45. cant locate fuse box to check fuse.


usually located drivers side behind kick panel or on lower portion dash..

Sep 02, 2010 | 1997 Infiniti.5 Q45

1 Answer

GARAGE DOOR OPENER ON VISOR


GOTO HOMELINK.COM

THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.

HOPE THIS HELPS

May 21, 2010 | 1997 Dodge Avenger

1 Answer

I have an Infinity q45 1999. The


take it to a local mechanic ,he should be able to put the light out for you and advise what the other lights are for

Mar 17, 2010 | 1997 Infiniti.5 Q45

2 Answers

How do you program the garage door opener on a 1997 buick riviera. Bought it used, no owners manual.


You'll need to open the transmitter in the car and match the frequency to the garage door reciever, assuming you have the fob for the garage door, opening this will reveal a set of tiny switches. This combination is the frequency you need. Open the transmitter in the car, and place all of it's switches in the same position as in the fob. If this doesnt work, then the governing frequency isn't the same and there's not much you can do. Hope this helps!

Mar 10, 2009 | 1997 Buick Riviera

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14185 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...