Question about Isuzu Pickup

1 Answer

Has no diagram available but alternator has two nut type connections and one terminal type connection coming from inside. What goes where??

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 320 Answers

Im not familiar with isuzu but they are pretty much all the same you have a two or three wire connector that plugs in and the you have a control voltage out terminal (usually 13.5v dc out put) the 2 post type connections will usually have a colored ring right up against the case of the altanator at the base of these posts the larger of the 2 wires will go on the red one. if they are not colored then there should be a + or - sign next to one of the posts. if none of these are present the larger wire is most gennerally mounted closer in to the center

Posted on Oct 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change alternator 2005 chryler 300


This answer covers:
2005 Chrysler 300 6cyl VIN "G" 3.5L SFI HO (72% of 2005 300's)
2005 Chrysler 300 6cyl VIN "R" 2.7L MFI DOHC (28% of 2005 300's)
2005 Dodge Magnum 5.7L engine

Alternator

Removal & Installation


WARNING - Precautions Section:
Disconnect negative cable from battery before removing battery output wire (b+ wire) from alternator. Failure to do so can result in injury or damage to electrical system.

2.7L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Remove alternator drive belt.
  4. Disconnect alternator field circuit plug.
  5. Remove B+ terminal nut and wire.
  6. Remove 2 lower mounting bolts.
  7. Remove alternator.
To install:
  1. Install alternator.
  2. Install upper bolt mounting bolt.
  3. Install 2 lower mounting bolts.
  4. Tighten bolts to 48 ft. lbs. (65 Nm).
  5. Install B+ terminal nut and wire. Tighten nut to 115 inch lbs. (13 Nm).
  6. Connect alternator field circuit plug.
  7. Install alternator drive belt.
  8. Connect negative battery cable.
3.5L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable.
  3. Remove alternator drive belt.
  4. Remove bracket bolts.
  5. Remove upper mounting bolt.
  6. Raise and support vehicle.
  7. Remove middle splash pan.
  8. Disconnect alternator field circuit plug.
  9. Remove B+ terminal nut and wire.
  10. Remove lower mounting bolts.
  11. Remove alternator.
To install:
  1. Install alternator.
  2. Install lower mounting bolts. Loosen install the upper mounting bolt.
  3. Tighten lower mounting bolts to 48 ft. lbs. (65 Nm).
  4. Connect alternator field circuit plug.
  5. Install B+ terminal nut and wire. Tighten nut to 115 inch lbs. (13 Nm).
  6. Install middle splash pan.
  7. Lower vehicle.
  8. Remove loose installed upper bolt.
  9. Install bracket and bracket bolt.
  10. Install upper mounting bolt and bracket.
  11. Tighten upper mounting bolt to 48 ft. lbs. (65 Nm).
  12. Tighten the bracket bolt to 40 ft. lbs. (54 Nm).
  13. Install alternator drive belt.
  14. Connect negative battery cable.
5.7L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect negative battery cable at battery.
  3. Remove alternator drive belt.
  4. Raise and support vehicle.
  5. Unsnap plastic insulator cap from B+ output terminal.
  6. Remove B+ terminal mounting nut at rear of alternator. Disconnect terminal from alternator.
  7. Disconnect field wire connector at rear of alternator by pushing on connector tab.
  8. Remove alternator support bracket nut and bolt. Remove support bracket. See Figure 1.
  9. Remove 2 alternator mounting bolts. See Figure 2.
  10. Remove alternator from vehicle.

Fig. 1 Alternator Support Bracket - 5.7L engine

7309257c-afe6-4c17-9422-d7fa2e3bd4b1.jpg

Fig. 2 Alternator Mounting Bolts - 5.7L engine

22b81ff7-7912-467f-9eaf-13ba2ff3a1a4.jpg

Oct 13, 2014 | 2005 Chrysler 300

2 Answers

Kia spectra 2006


Three BLK wires are attached to the positive battery terminal: one goes directly to the "START MOTOR". A second contains the alternator fusible link and connects to the alternator. The third goes to the engine room junction block.

May 02, 2014 | 2006 Kia Spectra

1 Answer

Stator wire from alternator


There are three wires that connect to the alternator: ORN to the field terminal, WHT/BLK to the stator terminal, and BLK/ORN to the battery terminal. The female spade must connect to a male spade on the alternator.

Apr 16, 2014 | 1981 Ford F 100

2 Answers

My1987 nissan pickup altrnatorwill not pull a charge, there is black wire connection that is under the boot. my black wire is just hanging there and not connected to anything but the alternator. where does...


Ground (almost always the black wire). Locate three or four connections on the alternator, depending on the type. One wired connection is black; another red; and the other can be blue, yellow, green and brown. The red and black wires are the main electrical connections. The others go to your ignition warning light system and voltage regulator.

Ensure the red wire is tightly connected to the alternator terminal. It usually is attached by a bolt. Move the wire to see whether it's loose; there shouldn't be any movement. If the wire is loose, tighten the nut using a suitably sized wrench.

Ensure the black wire is securely attached. It usually is connected to the alternator terminal using a bolt. Check whether the wire is loose; it should not move. If it does, tighten the nut using a wrench.

Hope helps.

Sep 28, 2011 | Cars & Trucks

1 Answer

Changing alternator



REMOVAL & INSTALLATION 2.2L Engines
CHRYSLER ALTERNATOR

  1. Disconnect the negative battery cable.
  2. Label and disconnect the wiring (for easy installation).
  3. Remove the air conditioning compressor drive belt, if equipped.
  4. Loosen the alternator adjusting bracket bolt and adjusting bolt. Remove the alternator belt.
  5. Remove the bracket and mounting bolts.
  6. Remove the pivot bolt and nut.
  7. Lift the alternator from the vehicle.

When lifting the alternator out of the vehicle on some years with A/C, clearance may be restricted by the condenser cooling fan assembly or the A/C compressor and mounting bracket assembly, if so, removal of one of these items will be necessary.
To install:
  1. Position the alternator against the engine.
  2. Install the pivot bolt and nut.
  3. Install the mounting bracket bolts, and adjusting bolt.
  4. Install drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

BOSCH ALTERNATOR
  1. Disconnect the negative battery cable.
  2. Disconnect the wiring and label for easy installation.
  3. Remove the air conditioning compressor drive belt.
  4. Loosen the alternator adjusting bracket locknut and adjusting screw. Remove the alternator belt.
  5. Remove the bracket locknut and mounting bolt.
  6. Remove the pivot bolt and nut.
  7. Remove the alternator from the engine.

To install:
  1. Position the alternator against the engine.
  2. Install pivot bolt and nut.
  3. Set the mounting bracket in place and install the bracket mounting bolt and locknut.
  4. Install the drive belts and adjust to specification.
  5. Tighten all the mounting bolts and nuts.
  6. Connect all alternator terminals.
  7. Connect the negative battery cable.

Jan 02, 2011 | 1994 Plymouth Voyager

1 Answer

How to replace alternator on 2007 toyota tundra


Hi. Please see procedure below:

Determine which alternator your Toyota Tundra will need. You'll want to be sure the new alternator is compatible with your Tundra's engine. Models built from 2000 to 2004 have a 3.4 L or 4.7 L engine. Models made from 2005 to 2006 offer options for a 4.0 L or 4.7 L engine. Starting in 2007, the Tundra is available with 4.0 L, 4.7 L and 5.7 L engines.

Disconnect the negative battery cable with a socket wrench. Remove the gravel shield if you need to access the alternator from under the car. Remove the electrical connector and unfasten the retaining nut on the alternator terminal with a socket wrench. This will allow you to remove the battery terminal wire.

Unfasten the lock nut, pivot bolt and adjusting bolt on the alternator with a socket wrench. Remove the drive belt and take the alternator off the vehicle.

Install the new alternator assembly. Use a torque wrench to tighten the lock nut to 25 ft. lbs. and the pivot bolt to 38 ft. lbs. Attach the adjusting bolt.

Connect the electrical harness and battery terminal wire to the alternator and fasten the retaining nut to the alternator terminal with a socket wrench. Install the gravel shield if you removed it. Replace the drive belt and restore it to the proper tension. Reconnect the negative battery cable with a socket wrench.

Thanks!

May 25, 2010 | 2007 Toyota Tundra

1 Answer

How to remove alternator from 1997 Chrysler Concorde?


e
3.3L Engine

  1. Disconnect the battery negative - cable.
b9a39c6.jpg

Fig. Wiring and nut locations



  1. Disconnect the alternator field circuit plug.
  2. Remove the B+ terminal nut and wire.
  3. Loosen the adjusting T-bolt, but do not remove it.
  4. Loosen the pivot bolt, but do not remove it either.
  5. Remove the alternator drive belt.
  6. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  7. Remove the alternator.
To install:
  1. Attach the alternator to the support bracket. Tighten all bracket and alternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).
  2. Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  3. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  4. Connect the negative - battery cable.

3.5L Engine

  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
3260271.jpg

  1. Loosen the belt adjusting bolt.
  2. Remove the alternator drive belt.
  3. Remove the bracket.
  4. Remove the lower mounting bolt and pivot bolt.
  5. Remove the alternator.
  6. Disconnect the alternator field circuit plug.
  7. Remove the B+ terminal nut and wire.
To install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
Hope helped with this (remember rated this help) Good luck.

Nov 03, 2009 | 1997 Chrysler Concorde

2 Answers

I need to replace my alternator


You need to first take off youre serptine belt. Inspect that and generally its a good idea to replace. Next there is a electrical connection on the alternator. DISCONNECT the battery FIRST!!!!!!!!!!!!!!!!!!!!!!!!! then disconnect the connection on the alternator, there are a couple of bolts that attach the alternator to the engine. and then simply bolt on the new one, re-attach the electrical connection and then re-install the (new) belt.

Aug 20, 2009 | 1992 Honda Accord

1 Answer

Chevy G20 1985 wiring (charging problem)


http://wareznuke.com/apps/3872/all-1979-2007-vehicle-wiring-diagrams-v42-rapidshare-warez


Jul 07, 2009 | 1985 Chevrolet Sportvan G20

1 Answer

Need to change the alternator


REMOVAL & INSTALLATION

3.3L Engine:
  1. Disconnect the battery negative - cable.
  2. Disconnect the alternator field circuit plug.
  3. Remove the B+ terminal nut and wire.
  4. Loosen the adjusting T-bolt, but do not remove it.
  5. Loosen the pivot bolt, but do not remove it either.
  6. Remove the alternator drive belt.
  7. Remove the adjusting T-bolt, pivot bolt, and mounting bolt, be careful not to loose the spacer.
  8. Remove the mounting bolt.
  9. Remove the spacer & washer
  10. Remove alternator.
To install:
  1. Attachthe alternator to the support bracket. Tighten all bracket andalternator (except for the wiring nuts) bolts to 40 ft. lbs. (54 Nm).Install the B+ terminal nut and wire and tighten to 75 inch lbs. (9 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Connect the negative - battery cable.
-------------------------------------------------------------------------------------------------
3.5L Engine:
  1. Disconnect the negative battery cable.
  2. Loosen the lower mounting bolt but do not remove it.
  3. Loosen the pivot bolt, but do not remove it.
  4. Loosen the belt adjusting bolt.
  5. Remove the alternator drive belt.
  6. Remove the bracket.
  7. Remove the lower mounting bolt and pivot bolt.
  8. Remove the alternator.
  9. Disconnect the alternator field circuit plug.
  10. Remove the B+ terminal nut and wire.
To Install:
  1. Attach the alternator and bracket to the engine, then tighten the mounting bolts to 40 ft. lbs. (54 Nm).
  2. Install the drive belt onto the alternator pulley. Make certain that the belt is seated correctly on the pulley.
  3. Install and tighten the B+ terminal nut and wire to 75 inch lbs. (9 Nm) onto the new alternator.
  4. Connect the alternator field circuit plug.
  5. Connect the negative battery cable.
If you need photos to follow then try this link...
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528006a83e

Jan 20, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...