Question about 2006 Audi A4

1 Answer

My passenger side head light needs to be adjusted it is pointing almost strait down

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

Just take your Audi to a State Inspection Station. It's a Slam Dunk for them. And it will be in accordance with the Law.

Best Regards

Posted on Oct 10, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Adjustment headlights 1994 Silverado

The lights have little adjustment screws and the lights are either spring mounted or will have plastic inserts .The whole idea is to be able to move the lights side to side or up and down to a degree .The best way to adjust them is when its getting dark park in front of a wall or garage door turn the lights on so you can see witch way are pointing. You want the drivers side pointing slightly down and toward the middle of the road and the passenger side can be higher but under 45 degrees and more in line with the side of the road .Head lights are for outer people to see you. So you don't want to blind people coming the other direction head on crashes are never good.

Feb 27, 2018 | Chevrolet Silverado Cars & Trucks

1 Answer

How do i adjust headlights

There should be a little screw to turn to adjust the head light. This will be in the head light assembly itself on top. If you have a manual they tell you in that also - but you should be able to find it any way. Some cars use a screw driver and some use a special type of screw driver you may have to buy.

Apr 13, 2015 | Cars & Trucks

1 Answer

How to adjust headlights

from the front or back of the head light , there will be 2/3 adjusting knobs / screws . Place the vehicle on a level surface about 3 feet from a plain coloured wall. You will see the centre of the beam( High beam). The centre of the beam is to be at the same height as the centre of the head light lense and properly adjusted pointing slightly to the passenger side of the vehicle . This prevents full beam in the eyes of oncoming cars.

Apr 20, 2014 | 2001 Chrysler Town and Country

1 Answer

How to adjust headlights for a 2008 dodge ram 1500

Extra lights should be the same height as the main lights of the vehicle. They must go out when you dip the head lights so you will need a relay for this to happen. They must also be independently switched so that they can be turned off Adjustment ---the center of the beam should be do higher than main lights at 3 feet from the lights and should point slightly to the passenger side of the road


Mar 24, 2013 | Cars & Trucks

1 Answer

Head light adjustment for a pt cruiser drivers side replace lamps low on drivers side when driving points down

there should be an adjustment screw or torx head bolt that will turn and raise the light

Mar 26, 2011 | Chrysler PT Cruiser Cars & Trucks

1 Answer

Trying to adjust headlights on a 2000 Plymouth Grand Voyager

On drivers side, Look for holes in rad support above headlights and you'll see a bubble level. Behind light housing you'll find small hex, or torx head screw just left and behind bubble level area. That's Horizontal adjustment. Now go over to right about 3 " from bubble level,just past where headlight mount is attached and look down hole for another hex, or torx screw head. That's vertical adjustment. Passenger side location will be obvious after finding drivers side adjustments.

Sep 19, 2010 | 2000 Plymouth Grand Voyager

1 Answer

How to set auto headlights

Ford Requires a special tool to adjust headlights, you can buy from ford or Mac or snap-on tools. Car must be level and you need it to be slightly dark outside so you can see what your doing. Adjust driver head light on low beam, as you are turning adjustment screw turn the screw for raising the head light and raise the head light up or down till it is 30 feet in front of you. you can take steps and measure it this way which would be 10 steps or ten yards on a normal person that is 5.8ins tall. then adjust the side adjuster so that when looking at the head light spot on the ground it is pointing to the passenger car side about one foot away from straight on. Meaning if you were going down the highway that the light would point down and slightly to the right not on the center road painted lines. Next adjust the passenger side to where it is the same height as the driver side, then hit your high beams. it should be aimed so that the lights do not shine into on com-ming drivers eyes. If you have a garage or a building that you can get thirty feet away and the car is level it will make it easier for you to see what your adjusting. Afterwords you may have to make a minor adjustment to both lights. I like to set them so that the passenger is slightly higher and a little to the right so you can see going down the road at night an avoid or see a deer or person to the right side of the road. Some states requires that a certified light mechanic to do this so be sure you are not voilating any laws when doing this. Thanks for using fix-ya and rate if this was helpful.

Aug 25, 2009 | 2003 Ford Expedition

1 Answer

I need to change the cabin filter on a 06 jetta

just stick your head up under the passenger side. there is a small panel with a few screws in it, and it drops strait down. nothing involved in the glovebox at all

Dec 07, 2008 | 2006 Volkswagen Jetta

1 Answer

My head light are real low how do i raise them?

There are adjusting screws on the headlight mounts, three of them I think. You may need a torx or allen wrench. Shine your low beams at the garage door or something and make the adjustments. Be careful not to let the low beams shine in other drivers' eyes. When you think it is right, park at night where you can walk in front of the car 100 feet or so and see that the low beams are not too high. The driver side light should point straight ahead, the passenger side light somewhat to the right.

Nov 15, 2008 | 1997 Chevrolet Tahoe

Not finding what you are looking for?
2006 Audi A4 Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

80608 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides