Question about 1995 Mercury Grand Marquis

1 Answer

Do i need to install the shims that come with the front brake pads on the 95 grand marquis

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 233 Answers

It is not necessary to install the shims. If, after replacing pads and installing caliper, the pads are loose, then you may install one shim at a time until it is tight. Also, if there were no shims on the previous pads, then there is no need to install the shims.

Posted on Oct 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake squeal


all brakes can squeal, (disc)
especially if lightly braking, it's just pad oscillation,
ever seen a tuning fork, sing. same deal.
some do so no matter what you do.... (been there many a time)
the cure is here, if possible.
1: missing parts, ive seen many shops replace pads and leave out the pad shims... do you need a diagram of what is there.?
i have it if you need it. ask.
2: if above parts not missing put on what i call pad glue.
all stores for cars sell this magic fix. a tube of pad glue,
in fact will be marked anti-squeal magic stuff.
3: some pads like to squeal others dont (brands)

btw i own same car and it does not squeal.
suzuki went chapter 11. and their online pages, (dregs) has has no drawings of the calipers. nor lists those parts above.
i have the FSM book on this car, 2004
and page 4B1 shows these parts. (amaZing huh>)
there are 4 shims
2 one each side.of a pad.
do you need part numbers, i have the official parts catalog too.
see here.

the part names are "anti-noise springs"
i found out that suzuki sells the pad set with new shims.
so if you bought them aftermarket and they are missing
you must reuse the old shims. suzuki dont sell the shims by self.
amazing huh?


I run RAYBESTOS.
they also have drag reducing clips..... upgrade.

Service Grade; Ceramic; Drag Reduction Clip Recommended H6046; OE Pad Material is Ceramic; Front; SGD680C

http://www.raybestosbrakes.com/magnoliaPublic/home/catalog/search.html?searchCategory=Automotive%20%2F%20Light%20Truck

as seen here, decide what you want then buy exactly that.
all my autostores in town can get them in 1 day or less.

or buy loaded calipers.
or use the glue and pray.

Jun 13, 2014 | 2004 Suzuki Grand Vitara

1 Answer

95 grand marquis passenger side rumbles when i hit bumps whats the problem


You did not say if noise is in front or rear of the car. It could be loose exhaust or sometimes the front calipers or brake pads will "float" against the turning rotors when they are jarred.

Feb 27, 2014 | Mercury Grand Marquis Cars & Trucks

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

Will I need a caliper reset tool kit to change the brakes on my 2007 toyota sienna or will a standard c-clamp do the job? And since it is an ABS system, I assume that brakes must be bled, correct?


Brake Pads Removal & Installation Front To Remove:
  1. Remove the front wheels. Front brake caliper (exploded view) toyota-09-00-5838.gif

  2. Loosen the caliper bleeder.
  3. Hold the slide pin; remove the 2 mounting bolts and remove the brake caliper from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, wear indicators and anti squeal shims.
  8. Remove the slide pins and bushings from the caliper support.
To Install:
  1. Lubricate the slide pins and bushings with brake grease.
  2. Install the bushing on the slide pin.
  3. Install the slide pin on the caliper support.
  4. Install the brake pad support plates on the caliper supports.
  5. Lubricate the anti squeal shims with brake grease.
  6. Install the anti squeal shims on the brake pads.
  7. Install the pad wear indicator facing upward and install the pads on the caliper support.
  8. Install the caliper on the support.
  9. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  10. Fill the reservoir and bleed the brakes.
  11. Install the front wheels.
Rear To Remove:
  1. Remove the rear wheels.
  2. Loosen the caliper bleeder. Rear brake caliper (exploded view) toyota-09-00-5842.gif

  3. Hold the slide pin; remove the 2 mounting bolts and rear brake caliper assembly from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, and anti squeal shims.
  8. Remove the slide pins from the caliper support.
To Install:
  1. Lubricate the slide pins with brake grease.
  2. Install the slide pin on the caliper support.
  3. Install the brake pad support plates on the caliper supports.
  4. Lubricate the anti squeal shims with brake grease.
  5. Install the anti squeal shims on the brake pads.
  6. Install the rear pads on the caliper support.
  7. Install the rear caliper on the support.
  8. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  9. Fill the reservoir and bleed the brakes.
  10. Install the front wheels.
prev.gif next.gif

Sep 18, 2010 | 2007 Toyota Sienna

1 Answer

How do I assemble the front break disc pads on a 2004 Toyota Tacoma 2wd?


To install:
  1. Siphon a small amount of brake fluid from the reservoir. Press in the brake caliper piston with the proper tool.
  2. Before installing the new pads, check the disc thickness and disc runout.
  3. Install the pad support plates.
  4. Install the anti-squeal shims to each pad.
    NOTE Apply disc brake grease to both sides of the inner anti-squeal shims.
  5. Install the disc pads so the wear indicator plate is facing downward.
  6. If removed, install the anti-squeal springs.
  7. Carefully install the brake caliper so the boot is not wedged.
  8. Install the wheel and tire assembly.
  9. Check and adjust the fluid level. Apply the brake pedal several times.
  10. Roadtest the vehicle for proper operation.

Mar 30, 2010 | 2004 Toyota Tacoma

1 Answer

Brakes to the floor 99 blazer


probably need to be bled again on that side

Apr 23, 2009 | 1997 Chevrolet S-10 Pickup

1 Answer

Instructions for replacing the front brake pads-2005 Hyundai Tucs


Jack the front of the car up, and make sure it is securely supported. Remove the wheel, remove the 2 guide bolts (located on the back of the caliper), and remove the caliper, hanging it by a coat hanger or wire to keep pressure off the brake line. Remove the pads and shims. Clean rotor with brake parts cleaner, and install new pads/shims. Repeat on other isde. Check with the parts store to see whether or not you need to use anti-squeak compound for your specific brake pads. Once you install them, you will need to bed the brakes to get the most use out of them. Accelerate to 30mph, then hard brake to zero (5-10 times), then repeat but to 60mph and hard brake to zero. Do this a couple times, and you will get very long life out of your brakes.

Apr 16, 2009 | 2005 Hyundai Tucson

Not finding what you are looking for?
1995 Mercury Grand Marquis Logo

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...