Question about 1992 Ford F250

1 Answer

The power steering on my F250 does not work. I removed the pump, and it seems to work on the bemch - I can't keep my finger on the delivery side of the pump on the bench. Is the system pependant on volume and pressure, or could the problem be with the steering box?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 195 Answers

It probably is the steering gear box.

Posted on Oct 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Do I have to remove the radiator in order to replace the power steering pump on my old Ford truck?


I would avoid that entire dilemma by just taking out the whole ps pump and replacing the pulley then, seems like a lot of work but it's worth it cuz the radiator removal is way more involved and more likely to cause problems with antifreeze leaks, also you probably only have to tilt the PS pump to get the pulley off so I would not disconnect the power steering hoses until I absolutely had to

Sep 24, 2014 | Cars & Trucks

1 Answer

How to remove power steering pump on a 2007 subaru b9 tribeca


before start job suction out power steering fluid out of pump using large sirenge or siphon pump then.you need a table vise and two pieces of wood.okay to remove power steering pump. you need to disconnect the ground cable.remove air intake duct.remove the pulley cover.remove the drive belt.disconnect power steering pump switch connector.disconnect the pressure hose and the suction hose from the power steering pump.cover power steering hose and pipe keep getting trash dirt and debris.remove the installation bolt of the power steering pump bracket.place the oil pump bracket in a vise btween two pieces of wood keep from damaging bracket and remove the two bolts from the front side of the pump.remove bolt from rear side of the oil pump.disassemble the oil pump and the bracket by inserting flat tip screw driver.to install tighten oil pump to bracket bolts 12 ft lbs. tighten the bolt from the rear side of the oil pump to 27 ft lbs.tighten steering hose eye bolts to 30 ft lbs.replace fluid bleed air out power steering system.

Nov 28, 2012 | 2007 Subaru B9 Tribeca

1 Answer

Im trying to change my alternator on my 97 chrysler sebring coupe lxi but it seems impossible to do it without taking other parts off to get it out and also put the new one in because its real compact


Hi there:
Check this procedure on 2.5L (VIN N) Engine...


  1. Disconnect the negative battery cable.
  2. Remove the right side under cover.
  3. Remove the speed control vacuum reservoir and related components as required for alternator access.
  4. Remove the power steering pump cover.
  5. Remove the A/C compressor drive belt.
  6. Remove the alternator/power steering pump drive belt.
  7. Remove the intake manifold plenum.
  8. Remove the upper alternator bracket.
  9. Remove the intake manifold plenum stay.
  10. Detach the electrical connections at the alternator.
  11. Unfasten the upper and lower bolts and remove the alternator. Be very careful not to damage neighboring components while removing the alternator.


8_22_2012_2_51_45_pm.gif

Fig. 8: Alternator assembly installation-2.5L engine (VIN N) - Zoom Image link HERE


To install:

  1. Connect the wiring to the alternator.
  2. Place the alternator on its lower bracket and install the upper and lower bolts finger-tight.
  3. Install the upper alternator bracket.
  4. Install the alternator/power steering pump belt, making sure it is properly seated.
  5. Adjust the drive belt to the correct tension using the belt adjuster, then tighten the upper mounting bolt to 16 ft. lbs. (22 Nm) and the lower mounting bolt to 30 ft. lbs. (41 Nm).
  6. Install the intake manifold plenum.
  7. Install the intake manifold plenum stay.
  8. Install the A/C compressor drive belt.
  9. Install the power steering pump cover.
  10. Connect the negative battery cable.
  11. Check the charging system operation.



Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 22, 2012 | Cars & Trucks

1 Answer

2004 ford f250 powerstroke. brake pedal is hard to press at first then goes straight to the floor also power steering quit working at the same time.


Hmm.. Low fluid in the power steering pump, broken belt driving the power steering pump, failed component causing loss of power steering fluid, failed power steering pump.

Check for a broken belt first, check the oil in the pump, look for leakage under the truck.

If the pump is low on fluid you want to put about half the amount in that you're going to need and then start the truck and turn the wheel slowly from stop to stop, each way- spend about ten seconds going from one stop to the other. This will allow any air in the system to be purged out in a controlled fashion, it can really spray if you get a big, compressed bubble of air in the system and release it quickly. Shut the truck off and top the steering pump up, check for leaks.

lp

Jan 05, 2011 | 2004 Ford F250

1 Answer

Replace power steering pump


The procedure is as follows:--- 1) Locate the power steering pump on the driver's side of the motor, which is mounted in front of the engine, near the top.2) You will see a fill spout coming out of the pump with a cap on it that says "power steering fluid."
3) Remove the negative battery cable from the battery
4) Remove the cap from the power steering pump,allow the fluid to drain into the pan.
5) Loosen the bolts that hold the power steering pump to the engine block with a socket wrench. Once the pump is loose, remove the belt from the pulley on the power steering pump. Remove the pump from the engine compartment.
6) Insert new power steering pump in reverse.
7) Reattach the power steering hoses and verify they are secure. Fill the new power steering pump with fluid to the full line shown on the dipstick on the back of the cap for your power steering pump. Place the cap back on the power steering pump.

Thanks. Keep updated for any more query. You can rate this solution and show your appreciation

Sep 22, 2010 | 2001 Hyundai Elantra

2 Answers

I have a 1993 F-250 4x4 speedo stopped working and power steering is making noise (fluid level is good)


Hi I just thought you might like to know that the VSS sensor(vehical speed sensor) on a 93 f250 is actually on the top center of the rear differential. It is basically a proximity type sensor not the old school gear and cable. It will take a 1/2" or 13mm wrench I believe to remove the single bolt holding it in and the it pulls out. I think they are around 25 bucks so it's cheap enough to fix the speed sensor.

Jan 19, 2010 | 1993 Ford F250

1 Answer

I changed powersteering cooler on a 2000 f250. lost alot of the fluid. it seems like air got in the abs system. The abs light is on and when you push on the pedal, you can here the powersteering making...


Hello hummelsautob.
Changing the power steering cooler can't allow air into the brake system. Two different fluid systems.
Your F250 has it's brake assist powered by the power steering pump.
Instead of using a vacuum assist it uses the hydraulic power from the pump.
When refilling your pump you have gotten air mixed in with the fluid. This turns it into a consistency something like whipped cream.
When in this state it isn't effective. Let it sit for a couple hours and let the air bubble out of the fluid. Recheck your level after this as it will drop.
This will make your brakes feel normal again.
Just a note on adding fluid to an empty power steering pump.
Add fluid to the reservoir but not to the top, turn the steering wheel back and forth slowly with the engine off. This will keep the fluid from foaming.

Dec 15, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Do you have the steps to replace the pump


Notes Power steering pump, replacing

Note: As the illustrations in this service information are used for different model years and/or models, some variation may occur. However, the essential information in the illustrations is always correct.

Preparation

Warning: Used fluid is considerably more dangerous than new fluid. Avoid skin contact with the oil.

Remove

  • the oil hose from the mounting on top of the power steering pump
  • the auxiliaries belt.
Note: If there is dirt in the fluid, drain the system and remove the hoses from the steering gear.

Removing the power steering pump/engine strut
Applies only to diesel cars:

Remove

113652509


  • the screw at the pump
  • the screw at the engine.
Leave the strut hanging in the delivery line.

Removing the feeder hose and delivery line
Install

113652510


  • the lock grip pliers on the feeder hose as close to the power steering pump as possible
  • the lock grip pliers on the return hose at the fluid reservoir.
Note: Place paper over the generator (GEN) as protection against oil.

Remove

  • the screw nipple. Remove the delivery line from the pump
  • the hose clamp. Remove the feeder hose from the power steering pump.
Warning: Avoid skin contact with the oil.

Removing the power steering pump
Remove

113652511


  • the 3 screws
  • the servo pump.
Installing the power steering pump
Install

  • the servo pump
  • the three screws. Tighten to 25 Nm .
Installing the power steering pump
Install

  • the feeder hose. Tighten the clamp
  • the delivery line. Do not tighten yet.
Installing the power steering pump/engine strut
Applies only to diesel cars:

Install

  • the strut
  • the screw at the engine. Tighten to 24 Nm
  • the screw at the pump. Tighten to 24 Nm .
Finishing
Tighten the delivery line. Tighten to 25 Nm .
Remove paper and lock grip pliers.
Install the auxiliaries belt.

113652512



Jun 06, 2009 | 2004 Volvo XC90

1 Answer

1984 F250 engine miss


its a bad valve, get your heads eplaced or rebuilt, if you dont the valve will drop into your cylinder and destroy the piston, i had the same problem and i didnt fix it and that truck no longer exists

Feb 23, 2009 | 1984 Ford F 250

1 Answer

Power steering


Try filling the P/S pump resevour and slightly turning the steering wheel side to side just enough to activate the P/S pump. Remove the return line from the pump and keep turning the wheel until you have a really good flow out. Be sure to keep adding P/S fluid while you're doing this. If it's still hard to steer, the pump bearings are now bad. Time to replace it.

Aug 03, 2008 | 1998 Plymouth Breeze

Not finding what you are looking for?
1992 Ford F250 Logo

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...