Question about 2002 Nissan Altima

Open Question

What is the torque specs for axle nut on a 2002 nissan altima

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

Ad
  • 99 Answers

SOURCE: What are the torque specs

the torque are not mention out side any authorised workshop for that you need to visit the nearest authorised dealer or service centre & leave the rest of work to them without any hazard or trouble or either can start from a torque of 25 to 45 lbs. do not exeed the limit or other wise the nut or even the Axel can get broken in the prossess of facinating it so till then my friend have happy motoring & see you soon.!

Posted on May 08, 2009

warlock61
  • 659 Answers

SOURCE: Axle nut torque spec

184 ft/lb

Posted on May 11, 2009

  • 15 Answers

SOURCE: what are the front axle nut torque specs for a

185 ft.lbs

Posted on Oct 10, 2009

  • 599 Answers

SOURCE: torque specs on replacing cv axle on 05 Pacifica

ok here we go tie rod=55 ft lbs axel nut= 180 ft lbs strut bolts= 65 ft lbs plus 90 degrees

Posted on Jan 07, 2010

Testimonial: "thank you very much!!!!!!!!!!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs on front cv axle nut 2007 Nissan altima


Spec is It's also sometimes listed 174 - 231 ft-lbs, I would do 200 ft-Lbs

Jul 12, 2017 | Nissan Cars & Trucks

1 Answer

FRONTAXLE NUT TORQUE ?


Click here to see the torque specs.

Dec 20, 2012 | 2002 Chevrolet Prizm

1 Answer

How do you install front hub assembly on 2008 nissan altima?


The torque spec is way more than any torque wrench
you will own

All you can do is get it as tight as possible with a very long
ratchet

The spec are from180 to 230 lbs on some axle nuts

Dec 13, 2012 | Nissan Altima Cars & Trucks

1 Answer

How do I replace the front wheel bearing hub assembly on a 2006 nissan altima


The front wheel bearings are pressed into the nuckle. You will need a kit to press them in and out or visit a shop or machine shop and have them press the bearing in and out.

To do this you will need to remove the knuckle.

1. remove the tire
2. remove the axle nut
3. separate the outer tie rod end from the knuckle
4. remove the caliper and rotor
5. separate the lower control arm from the knuckle.
6. remove axle from the hub.
7. unplug ABS sensor
8. remove the strut to knuckle mounting bolts.

With the knuckle removed the bearing can be pressed out and the new one pressed in. The most important step when reassembling is torquing the axle nut to the proper spec. Failure to do so will cause the new bearing to wear out prematurely!!!

It is also common for the hub (the part with the wheel studs) to wear out and need to be replaced as well.

If you have any questions let me know!

Oct 14, 2011 | 2006 Nissan Altima

2 Answers

Torque specs,rod bearings,2003 nissan altima 2.5


I need the torque specs for the connecting rod and main be

Sep 10, 2011 | Nissan Altima Cars & Trucks

1 Answer

What are the torque specs on the head bolts and rod caps on a 1999 nissan altima with a 2.4l engine


Rod cap nut's

Step 1 -10-12 Ft.LBS
Step 2 - 60-65 Additional Degrees


Head Bolt's

Step 1 - 22 Ft.LBS
Step 2 - 59 Ft.LBS
Step 3 - Loosen all bolt's
Step 4 - 22 Ft.LBS
Step 5 - 86-91 Additional Degrees

bcas1298_8.gif

Dec 11, 2010 | 1999 Nissan Altima

1 Answer

New hub assembly


General Motors has released a new style drive axle nut for many 97-03 models. This new and improved nut is a torque prevailing style nut(basically it distributes the torque properly) for mor consistent clamp load on the wheel bearing. The new nut is silver in color and the old nut is usually black in color. They have also lowered the torque on most all of the models. The original torque for many of these vehicles was 284 FT/Lbs. THey have dropped this torque to 173 Ft/Lbs, then they dropped it again down to 112-118 Ft/Lbs.

Jun 24, 2009 | 2002 Chevrolet Malibu

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
2002 Nissan Altima Logo

Related Topics:

553 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...