Question about 2000 Dodge Durango

1 Answer

I have a 2000 dodge durango that wont start. I changed the crank shaft senser and the cam shaft position senser and the cap and rotor button but still wont start

Posted by on

  • cheap repair Oct 10, 2010

    have you checked the fuses and relays as well?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Dodge Master
  • 3,854 Answers

Have you checked for your DTC code?? The code may help you address the issue that is keeping your engine from starting.

ON-BOARD DIAGNOSTICS

1. Cycle the ignition key ON-OFF-ON-OFF-ON within 5 seconds. To cycle the ignition key ON means to turn it only as far as it takes to get the radio to come on. It does not mean to turn the engine on.

2. Count the number of times the "check engine" lamp on the instrument panel flashes on and off. The number of flashes represents the code. There is a slight pause between the flashes representing the first and second digits of the code. Longer pauses separate individual codes. For example, flash-flash-flash [pause] flash-flash represents the code 32.

A code of "55" represents end of error codes. If this is all you get then no error codes are stored in the computer. This is the normal condition for a neon.
CODE Description of Trouble Code
11 Timing belt skipped 1 tooth or more from initial learned value, Intermittent loss of either camshaft or crankshaft position sensor, No crank reference signal detected during engine cranking
12 Direct battery input to PCM was disconnected within the last 50 key-on cycles
13 No change in MAP from start to run
14 MAP sensor voltage too low
15 No vehicle speed sensor signal
17 Closed loop temp not reached or engine cold too long
21 02s sensor problem (oxygen sensor), upstream or down stream
22 Engine coolant temp sensor out of range
23 Intake air temp sensor out of range
24 Throttle Position sensor out of range
25 Idle air control motor circuits, target idle not reached (+/- 200),vacuum leak found
27 Injector control circuit
31 Evap purge flow monitor failure or evap solenoid circuit
32 EGR system failure
33 A/C clutch relay circuit
34 Speed control Solenoid circuits
35 Rad Fan control relay circuit
37 Torque converter clutch solenoid CKT or park/neutral switch failure
41 Generator field not switching properly
42 Fuel pump relay control ckt, Auto shutdown relay control ckt, No ASD relay output voltage at PCM, Fuel level sending unit volts out of range, Fuel level unit No change over miles
43 Multiple/ single cylinder misfire
44 Battery temp sensor volts out of range
46 Charging system voltage too low
51 Fuel system lean
52 Fuel system rich
53 Internal control failure
54 No Cam signal at PCM
55 End of error messages (If you get this only, no errors were found)
62 PCM failure SRI mile not stored
63 PCM Failure EEPROM write denied
64 Catalytic Converter Efficiency Failure
65 Power steering switch failure

Good luck and thank you for using fixya and keep us posted

Posted on Oct 10, 2010

  • patty Aug 15, 2013

    YES WE ALREADY HAD IT ON A COMPUTER JUST KEEPS GIVING CAM AND CRANK SENSOR CODE BUT WE HAVE ALREADY REPLACED THEM.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Engine rotates but wont start


run fault codes .check cam/crank shaft position sensors. Check that the cam shaft is turning (broken timing belt/chain). Check immobiliser operation

Sep 09, 2014 | 2005 Mercury Sable LS

1 Answer

1998 dodge dakota 3.9 runs great for about 10 min. than starts to miss and backfire no check engine light


you may have a plugged fuel filter as you don`t say if you have changed it. also have your fuel pressure tested with a gage, it should run about 36 lbs pressure if its multi-point fuel injection or run at about 15/18 lbs pressure if its a throttle body.

Jul 17, 2014 | 1998 Dodge Dakota

2 Answers

What's your problem?I did all these changes to my 1999 Dodge Durango. They are distributor cap, rotor, wires, spark plugs, and pick up coil. My fuel pump is working I also check the alternator and it...


Check that the crank shaft position senser is plugged in and working and not broken this will cause your comp to not send fire to you coil and it won't fire hope this helps you

Oct 12, 2011 | 1999 Dodge Durango

1 Answer

Replaced engine in 1999 dodge durango 5.2 and it wont start, will crank but not start.


Hi Wilson,
Check all your computer connections....If the engine is diesel make sure all air is removed from the fuel system. the crank shaft sensor and the cam shaft sensor are critical....Check the the cables are not broken and nothing has been trapped between two components which have been tightened.
Regards Johngee10

Feb 06, 2011 | 1999 Dodge Durango

1 Answer

2000 dodge durango wont cranks but wont start...


had same problems with cranking and wouldnt start , i had no spark not sure if you do but if not after performing tune up and still had no luck , i changed my camshaft position sensor under distributor and rotor , and she started right up . good luck

Mar 15, 2009 | 2000 Dodge Durango

4 Answers

I have a 2000 dodge durango, I have a code P0320.


I put in a new crank positioning sensor and it fixed my problem. 42.00 dollars from NAPA. took about 2 hours to change it.

Mar 09, 2009 | 2000 Dodge Durango

1 Answer

Rotor cap on my 2000 dodge durango stuck and will not budge.


take a pair of channel locks and rotate it back an forth until you dislodge any material that is wedging it in position

Feb 15, 2009 | 2000 Dodge Durango

Not finding what you are looking for?
2000 Dodge Durango Logo

822 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...