Question about 2004 Mitsubishi Endeavor

Open Question

My 2004 endeavor has a driver power seat that has completely stopped working, is there anyway to fix it or do i have to replace the seat?

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 2004 Mitsubishi Endeavor power liftgate has

check for any recalls on that issue with the manufacturer, cold condensation may worked its way inside the electronics and ruined them.

Posted on Jul 08, 2009

Ad
jim9813
  • 124 Answers

SOURCE: 2004 Supercrew Lariat no driver power seat or pedal adjust

Maybe, you can diag yourself with a test light and an ohmmeter. These will cost less at sears than having a dealer diag it. Check fuse 109 in the cab, that's the fuse for the driver's seat module. If that fuse is ok, then check power at the module. It's a little black box under the driver's seat with i think 3 connectors. Back probe the dark green wire at the connector with a test light, you should have power, even with the key off. If not, repair the circuit. Clamp the test light to battery positive and back probe the black wire, if the light does not light, repair that ground circuit. Test the memory set switch by measuring with an ohmmeter points 7 and 2, 7 and 6, 7 and 5 resistance should be less than 5 ohms, if not replace it. If all these tests pass, disconnect the connectors from the module and give 12v to the red and white wire. If the seat moves, have the module replaced at the dealer, it will have to be programmed.

Posted on Aug 10, 2009

ourhowse
  • 2007 Answers

SOURCE: Drivers Power seat broken-the support metal arm-2004 Grand Cher

Should just be 4 bolts holding the seat to the floor, and unplug the wires. Only way to fix it is weld it, or get a different base from an auto wrecker.

Posted on Nov 02, 2009

tneubauer
  • 437 Answers

SOURCE: 2004 suburban drivers side power seat and both

This is controlled through the body control module you will require a scan tool to access it.

Posted on Jan 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Mitsubishi Endeavor. Blower motor no longer works. Right before completely dying. If I would turn left I heard water flowing and blower barely worked. Now no water noise or fan working. Help plz


2004 Mitsubishi Endeavor AC transistor blower fix - YouTube

? 8:02
www.youtube.com/watch?v=6g_xozxuziE
Mar 19, 2015 - Uploaded by Peter Zafra
How to fix a Mitsubishi endeavor ac blower that stopped working. ... 2008 Mitsubishi Lancer HVAC Blower Motor Install How To - Duration: 9:07.

Sep 10, 2015 | Mitsubishi Cars & Trucks

1 Answer

Hi, I have a 2004 Mitsubishi Endeavor and the power mirrors act like they have zero power and also the steering wheel radio controls do not function at all. checked all fuses and no luck. Mirror fuse was...


Try checking power and grounds to the switch. If good replace switch. If no power or ground check for broken wires in door hinge area. As for the radio, I do not believe it is on circuit with the mirrors, Thus a seperate issue. probably the radio itself.

Dec 25, 2014 | 2004 Mitsubishi Endeavor

1 Answer

Our 2004 Mitsubishi Endeavor continues to leak water in the driver's floor board and you hear it splashing in the compartment. We have had it reparied two times. And it works for awhile and then ret


You most likely have a leak in the heater core.
It will have to be removed , repaired or replaced.

Any independent garage can handle the job.

Jun 02, 2014 | 2004 Mitsubishi Endeavor

1 Answer

2004 Chrysler Crossfire Subwoofer behind driver seat is blown how do you remove the panel to replace it?


Did you have any luck with this? Mine has the same issue, and the power seats work when they feel like it...so I don't know how I'd get the thing out of there anyway.

Feb 02, 2011 | 2004 Chrysler Crossfire

1 Answer

Air condition stop, and motor engine dosen't work good


remove and replace the power relay in the electrical fuse and relay box located in the engine compartment. the relay is labeled via the underside of the cover. location is driver side of vehicle near the firewall.

Aug 07, 2009 | 2004 Mitsubishi Endeavor

1 Answer

Electrical windows & door locks not working


Sounds like a possible BCM body controll module has shorted out partially. I think these are only at dealerships.

Jan 09, 2009 | 2004 Mitsubishi Endeavor

1 Answer

2004 mitsubishi endeavor passenger rear window off track


Yea its actully quite simple, but expensive. The regulator needs to be replaced. I have already replaced my right rear, but I think my driver side is going out also, sounds like it anyway.
Thank God I bought a third party warrnty and they took care of everything. Zurich is the name of the company. I purchased the one with no deductible. Anyway I wish I had a better solution-but its awful hard to do your self.
Apache105

Sep 29, 2008 | 2004 Mitsubishi Endeavor

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

Related Topics:

331 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...