Question about 1996 Toyota Camry

1 Answer

Brake pad springs took apart and cant put together again how do they go in

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 84 Answers

Typical drum brake diagram

Posted on Oct 09, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Humming noise driving

all brake pads can sing. all.
and is not a problem at all. they vibrate like a guitar string.
when very lightly pressed (you only said pressed, so.....)
some folks hate this,
so buy the no sing glue for the backing plates or add the High MPG
springs that retract the pads. ()mods)

the older cars the caliper piston seals, lose a property called the stiction
factor (this helps retract the piston) so new seals can help.
the seals do act as tiny springs. when fresh. and new.
sticking caliper guide pins took, can cause noise.
some can rust. my jeep has sst pins in teflon sockets that cant rust.
some cars have missing parts, in the pads, due to shoddy brake work.
they dont put back the anti squeel shims and such.
so go to honda dealer oem parts. dot come and see your brakes
and all parts that came new on car. missing parts . ?

Feb 06, 2014 | Honda Cars & Trucks

1 Answer

1988 crown victoria ltd new brakes seizing up

Where to start. . . .
A defective hose would only affect that wheel.
A faulty booster or master cylinder could cause the front wheels to lock and at varied amounts. You may have a metering block or just a junction block for the front lines. It would be mounted near the frame if you have one. Some Ford models from 88 - 92 used a master cylinder with the metering valve built in.
Its possible the front calipers got hot enough with the old pads to damage both front hoses.
I would want to know what it takes to release the pressure on the pads. Do you have to take the hoses loose, or just the bleeder screws on the calipers ? Or are the calipers not sliding back and forth ?

May 28, 2013 | Cars & Trucks

1 Answer

Took off back brakes to replace pad. Need help

use a flat tip screw driver put flat edge on pin where spring hooks up put spring on brake pad the hook onto screw driver lift up as lifting spring will slide along screwdriver and into place .

Apr 16, 2010 | 1991 Nissan Maxima

1 Answer

How can I get the springs back on rear brake pads on 1999 suburban? I took the brakes off and now I am having problems putting the springs back on. Any solutions on how to make this a little easier?

there is no springs on brake pads,
if you mean rear drum ,brake shoes,which springs are you having trouble with,the round cylinder springs that hold the shoes fast to the backing plate or the the return springs that bring the shoes back after being pushed out by wheel cylinders.

Jan 02, 2010 | 1999 Chevrolet Suburban

1 Answer

How do i Replace the Front Brake pads and rotors on my 2001 Honda Accord

Hang on, because you're in for a ride on this one. This is one of the most difficult rotor replacements there is. You will have to buy new nuts for the cv shafts on the front, remove the old ones (usually require an impact wrench), unbolt the pad bracket, unbolt the hubs, unbolt the rotors from the hubs (careful, these bolts like to break off), and replace the rotor. When you're done with this, put it back together the same way you took it apart.
Unless your rotors are excessively thin, scored badly, or warped (your brake pedal will vibrate) you usually don't need to replace them. You can use sandpaper to scratch them up, and use them again. Good luck, and have fun!

Nov 20, 2009 | 2001 Honda Accord

1 Answer

'93 Olds 88 brake reassembly. Very stiff spring.

put the bar on the shoes before you attach the clips and springs.

Oct 04, 2009 | 1988 Oldsmobile Delta 88

1 Answer

Brake problem

it sounds like your disk brakes are the problem. two ways to fix the problem. champfer your brake pads or basically glue your pad to the caliper piston with some stuff called disk brake quiet. the shop probably does not want to take your whole front brake system apart again. good luck.

May 04, 2009 | 1996 Ford Windstar

1 Answer

1997 rear drums

Actually, if you want, your local Autozone can print you out instructions with pictures, and they don't charge. (At least, they didn't when I worked there)

Dec 04, 2008 | 1997 Ford Club Super

Not finding what you are looking for?
1996 Toyota Camry Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides