Question about 1992 Honda Prelude

1 Answer

Re setting check engine light on a 1992 Honda prelude

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 14,036 Answers

YOU CAN DISCONNECT NEGATIVE BATTERY CABLE FOR 10 SECONDS TO RESET ECM.BUT IF YOUR CHECK ENGINE LIGHT KEEP COMING ON.HAVE VECHICLE SCANNED TO SEE WHAT TROUBLE CODE YOU ARE GETTING.

Posted on Oct 09, 2010

  • Nichol S. Apr 26, 2012

    You can also remove the 7.5 fuse inside the drivers feet,fuse panel. Also, you can retrieve your own codes on almost any vehicle by finding the OBD(on board diagnostics) plug...on the 92 prelude 2.3l dohc, it is at drivers right foot panel. It is a small plug with only 2 wires connected, A and B. You can use a small paper clip, one side into the A slot, and the other side of the paper clip into the B slot.,,,with the key off of course. Then turn the key to the on position and look for the: service engine soon" light to flash. Count the long, then the short and you will have your codes.. Hope this helps:)

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set crankshaft timing on 1992 honda prelude 2.3 liter?


here is a u-tube video with a good tip for making sure the timing marks dont get move once set may help
How to replace timing belt on Honda Prelude 92 96 2 3 lt H23a1

Jul 28, 2014 | 1992 Honda Prelude

1 Answer

Set timing on a 1992 honda prelude, 2.3 engine, I REPLACED THE DISTRIBUTER AND NOW ITS COMPLETELY OUT OF TIME, detailed instructions please


  1. Locate the service check connector and, if applicable, remove the cap. On 1988-91 Preludes, the cap is yellow and the connector is located next to the vacuum control box in the engine compartment. On 1992-95 Preludes, the service connector is located under the middle of the dash. On 1990-93 Accords, the connector is blue and is located behind the right front kick panel, under the dashboard. On 1994-95 Accords, the service connector is located behind the glove box. Use a jumper wire to connect the two terminals of the service connector.
  1. Following the manufacturers instructions, connect a timing light to the engine. The positive and negative leads connect to their corresponding battery terminals and the spark plug lead to No. 1 spark plug wire.
  2. Make sure that all wires are clear of the cooling fan and hot exhaust manifolds.
  3. Set the parking brake and block the front wheels. Start the engine. Check that the idle speed is set to specifications.
  4. Point the timing light at the timing marks. On all models except 1994-95 Accords, the marks are on the flywheel. On the 1994-95 Accords, the timing marks are on the crankshaft pulley. When the engine is idling, the red mark must align with the pointer. Some timing marks are indicated by 3 lines; the center one must be aligned with the pointer.

  1. If necessary to adjust the timing, loosen the distributor hold-down bolt(s) and/or nut and slowly rotate the distributor in the required direction while observing the timing marks.
  2. To complete the adjustment operation, tighten the hold-down bolt, taking care not to disturb the adjustment.
  3. Switch the engine OFF . Reinstall the rubber plug in the timing window and remove the timing light. Remove the jumper wire.



0900c1528005f368.jpg

Fig. Fig. 4: Service connector on 1988-91 Preludes


0900c1528005f36b.jpg

Fig. Fig. 5: Service connector on 1992-95 Preludes

Mar 03, 2011 | 1992 Honda Prelude

1 Answer

The D4 transmission light is flashing, the speedometer quit, and the check engine light came on. Fluid is good, and it shiftd fine into all gears. What could be the problem


The D4 light is a transmission code light for those cars probbly reading the speedometer going out and the check engine light the same. Have the codes checked or simply replace it. Here is one of many places to find it (just to give you a price range) http://www.bing.com/shopping/search?q=92%20prelude%20speedomotor&qpvt=92+prelude+speedomotor     best of luck

Oct 21, 2010 | 1992 Honda Prelude

2 Answers

Engine will not start


THEN THE CAM TIMING MUST BE WRONG OR THE INJECTOS ARE NOT DELIVERING FUEL, HAVE YOU TESTED THE INJECTORS TO SEE IF THEY ARE PULSING AND DELIVERING FUEL? U CAN TEST THIS WITH A TOOL CALLED A "NOID" VER Y EASY TO USE, PLUGS INTO THE INJECOTR HARNESS AND FLASHES IF THEY WORK. ALSO VERIFY THE CAM IS SET RIGHT

Oct 20, 2009 | 1992 Honda Prelude

2 Answers

Honda Prelude 1992, doesn' start!


Sounds like a crank postion sensor. Is this only when the car is hot/reached operating temperature

Aug 07, 2009 | 1992 Honda Prelude

1 Answer

I just bought a 1992 honda prelude, what kind of coolant do i use


50/50 ratio of regular Anti-freeze. Prestone is pretty popular. also consider getting your coolant flushed and filled instead....chances are it hasn't been done anytime before you bought it. it will prevent headaches and save your engine as well. One over heat situation and its likely your engine will be turned into garbage.Heat kills engines.

Mar 14, 2009 | 1992 Honda Prelude

2 Answers

TAPPET SETTINGS HONDA PRELUDE 2.2 IMPORT


Intake valve clearance 0.15mm-0.19mm (6-7 thou); Exhaust clearance 0.17mm-0.21mm (7-8 thou). All measurments COLD engine. 2.2 VTEC Prelude engine 1992-1996, import and UK.

Feb 22, 2009 | 1994 Honda Prelude

4 Answers

D4 LIGHT


rate me FIXYA!...thanks
44926db.jpg
f77bb4e.jpg
52a3c74.jpg

Jul 05, 2008 | 1992 Honda Prelude

Not finding what you are looking for?
1992 Honda Prelude Logo

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...