Question about 1992 Honda Prelude

1 Answer

DO I COMPASS THE CALIPERS WITH A C CLAMP OR DOES IT TURN REAR BRAKES HONDA PRELUDE

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 58 Answers

I would remove the cap to the master cylinder, then barely crack the bleeder valve. after that then you can compress the caliper with a c clamp. be careful, your gonna lose some brake fluid.

Posted on Oct 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am the original owner of my 1998 Honda Prelude, which has 90,000 miles. It has not been driven much recently due to illness so I brought it to a mechanic to check it out. He says it needs rear rotors and...


No! It doesn't sound right. I can see the calipers developing leaks depending on the weather there, but not the rotors. So either you already had bad brakes before it was parked or someone needs to give the mechanic a reality check.

BTW: Telling mechanics upfront that you want all parts that they replaced returned to you, will make it harder for them to slide something past you.

Aug 26, 2011 | 1998 Honda Prelude

3 Answers

I CHANGED MY ROTORS AND BRAKES,AND I BLED THE BRAKES BUT THE PEDAL STILL HITS THE FLOOR .


Unfortinatly your pads and rotors may have had nothing to do with this. It sounds like either really bad rear wheel cylinders or a bad master cylinder. I would tell you the master cylinder is the problem though.

Jun 03, 2011 | 1995 Chevrolet Tahoe

1 Answer

Iv cleaned the brakes and cilinderon my honda civic coupe v reg but the brake is not releasing itself


If ft.brakes are sticking it should be calipers are bad 7 times out of 10...or some may have a ft.
metering valve.....but should be ft calipers sticking...sometimes the hose will go bad but normally it is calipers.....if it is the rear sticking the emergency might be slightly engaged or the rear brake
proportioning valve is bad......jack car up and see which wheels are freezing up by turning the wheel
round and round.see which one is hard to turn....if only one ft wheel is hard to turn change both calipers if hose's look good.if hose's are drycracked change them also because they will go bad internally....although it is normally the calipers.....calipers can be rebuilt ....it has an o-ring around a piston that freezes....but sometimes the piston gets craters inside and you will waste time by trying to rebuild..

Feb 19, 2011 | 2000 Honda Civic

1 Answer

Rear brake caliper piston will not go back on Honda Prelude


Have you compressed the caliper all the way? To do so, use a large 'C' clamp, open the bleeder valve slightly, and compress it be tightening the clamp. It should now fit over the brake disk. Let me know it you need further help.

Apr 05, 2010 | 1997 Honda Prelude

3 Answers

1992 Honda Prelude Si brake caliper piston prob


As your car has a handbrake fitted to the rear calipers,you will need a piston wind in tool to retract the piston fully back into the caliper as when you adjust your handbrake the piston automatically winds itself to the required position for usage without this tool you are getting nowhere,so get hold of a tool to do the job and you should not have problem unless the piston has totally siezed on the screw then you will have a problem being the only way to repair would to be a new or refurbished caliper.

Feb 28, 2010 | 1992 Honda Prelude

3 Answers

How do I get the rear brake cylinder depress back in when putting on new brakes.


If it does not push back with a c-clamp,then it will turn to go back in,the right side,and the left side will turn either left,or right hand to go back in,depending on witch side you are working on.

Nov 29, 2009 | 2004 Ford Freestar

1 Answer

2003 Honda Civic Si - Changing rear brake problem


Ford taurus's have the same setup on the rear calipers and it requires a special tool or persistance on your part with a pair of channels lock pliers and a c clamp. turn the piston clockwise as you press it in with a c clamp or get the tool mentioned below.

Harbor Freight has this special tool... found HERE

And yes, once you get the piston in it will come back out on it's own and yes will automatically readjust.

Nov 19, 2008 | 2003 Honda Civic

1 Answer

1989 Honda prelude brakes sticking.


pistons in brake r sticking need to b stripped n cleaned

Nov 16, 2008 | 1989 Honda Prelude

1 Answer

Rear brake calipers


A big pair of channel locks will collaspe the caliper but it does take some muscle or you can release the brake line nut and releave the pressure but then you would have to bleed the brakes.

Aug 03, 2008 | 1990 Honda Prelude

Not finding what you are looking for?
1992 Honda Prelude Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...