Question about 1991 GMC Sierra

1 Answer

No gas flows into carb - 1991 GMC Sierra

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

2 things to look into. #1 you could have a clogged fuel filter or the sending unit located on the top of your gas tank needs to be replaced or you have a bad ground wire on it. You can take the fuel filter off and blow through it to see how much flow your getting (should go through without alot of restriction). With the sending unit, stand outside your truck and turn the key so the power comes on the truck. you should hear a small (whir) noise coming from the gas tank. If you dont hear that then check for a bad ground connection.

Posted on Jan 05, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Own Kubota ZG222 zero turn lawn mower. Leaking gas, no start. Pulled the oil dip stick- gas flowed out. Gas entering engine. Can this be repaired without replacing the entire carb?


Yes, it should be able to.. take the carb to a qualified professional.. the needle and seat assy may have dirt/crude in it, ... (the needle and seat are what controls the flow of gas into the float bowl)..preventing the needle from seating and stopping the flow of gas..this is why the engine filled with gas.. drain the oil...let the engine "air out" for a while.. R&R the oil filter... install a new gas filter (or 2)..The mechanic will be able to tell you whether the seat can be replaced.. some are pressed/swedged in place and cannot be removed, the needle has a "rubber" seal where it meets the seat.. if its damaged it must be replaced..( I would replace it anyway - cheap insurance)..UNLESS something is actually broken, you DO NOT need a new carb!!!

Jul 10, 2017 | Cars & Trucks

2 Answers

1984 S10 wont run fuel coming out at pump but doesnt seem to supply carb. has new filer. when primed it runs for a few seconds.


Is this a carbed engine, that usually means mechanical fuel pump? Take fuel line loose from carb, aim into container, crank engine, does gas flow? If so, have to check float bowl in carb to see if any gas, if no gas, need a carb kit in my opinion.
I don't know liter size of engine? If fuel injected, let us know.

Mar 20, 2017 | Cars & Trucks

2 Answers

After I drive my truck for awhile and then it sits for a half hour or so it hard to start like its not getting enough gas I put some in carb. It starts but dies after it burns it put new fuel filter


  1. disconnect the fuel line at carb
  2. stick it in a container and crank engine
  3. check the flow if really good THEN:
  4. check the float level and acc. plunger on the carb.

Hope this helps Mike

Feb 15, 2016 | Cars & Trucks

1 Answer

1987 jeep comanche will stay runnning only when spraying carburetor cleaner in carburetor or when you pump throttle rapidly


Hello
It sounds like a glogged fuel filter or throttle body problem. Disconnect gas line at carb get a small jar or can to catch gas, hold gas line in jar and have someone crank engine, If you have good gas flow to carb then Its a throtle body problem, (Throtle body and carb are same thing just in case you did not know)could be electrical or mechanical problem at throttle body, Its usually electrical, fuel flow meter. Hope this helps

Oct 23, 2012 | 1987 Jeep Comanche

2 Answers

I have a 1991 GEO Tracker that's not getting gas in the carb...the gas is up to the carb but is not going in to the carb.


Disconnect the carburetor from the gas line, and rebuild it, blowing out the jets with compressed air, and adjusting the float so that it will allow gas to flow into the carburetor bowl.

Aug 03, 2010 | Cars & Trucks

3 Answers

I have a 2 barrel carb off a 283ci 1967 chev carter carb


no spring poss small wire from needle to float! the way it works is float is up needle close because float bowl full--when fluid or gas goes down valve opens lets fluel in.ck full pump disconnect line at carb crank over with guage should have apprx 7psi of press not less then 5psi carefull gas flameable

Aug 30, 2009 | Chevrolet Chevy Cars & Trucks

1 Answer

89 JEEP WRANGLER... GAS IS GETTING TO CARB, BUT NOT INTO CARB, WHAT COULD BE HOLDING GAS OUT??


If the gas flows all the way to the carb but no gas is spraying, than there is a clog in the line, or the nozzle, or you may have a dirty or debrit in carb itself.

May 10, 2009 | 1989 Jeep Wrangler

3 Answers

Excessive gas use


if it a carb not tb there is a couple set screws on the carb. run at 700 rpm or idel u need to put a vacum gauge on trying to get the high vacum out of it. on the carb to set the vacum what kind of carb is it these set screws control fuel and air flow when adjusted right. should be better gas saver question is 2 b or 4b carb

Mar 05, 2009 | 1988 Chevrolet Cavalier Z24

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...