Question about Buick LeSabre
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Don it. Good half day for amateur. Get Chilton 86-99 Bonneville, 88, Lesabre manuel.. Tricky to find bolts are under end flaps on door close handgrips. Took me a day to figure that one out. Others under light at lip of back of door. Book indicates to strart with window 3/4 up if you can. Flip up window control at rear of panel. After all screws are out raise outer edge of armrest and look for notches 4" and 11-1/2" from rear of armrest to slide inward to remove. There are screws under the door handle too. Screws everwhere. When pulling bottom of panel from door lift with a notched bar to avoid tearing the fasteners out of the cardboard panel. Two screws behind seatbelt notch at top need to come out to allow positioning the glass. The panel at the bottom of the top opening can be removed for more fredom in positioning the glass when reinserting the ball in the lower track on the window. Tape glass with duct tape to keep it from falling. Drill the factory rivets that hold the old regulator and I replaced with stove bolts with nylon locknuts slotted head to the inside the car. Can't remember the size, probably 1/4 or 3/16". Remove speaker if in front bottom of door to use your hand to do work in the door. You must twist the regulator forward with window 1/2 down to remove the ball from the socket in the bottom sliding metal track at the bottom of the window. Don't drop the window after removing the socket, tape it in place. Don't know what you do if you cannot move it to 1/2 up position. By the way, the body shops say you must use rivets, not screws or it will shift, but I have had no problems with the screws for reinstallation several years old. The rivet they use take a big hydraulic pop rivet gun that you won't have. Good luck, I don't envy you. Need to do other window on my 91. The window control may not be the same on the Custom, mine is the Ltd. you may be able to remove the motor from the regulator in the door without removing the regulator if you can figure out how to get the bolts that hold the moter to the regulator. inside the door.
Posted on Jan 02, 2009
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
Posted on Aug 14, 2009
Are you sure the blower motor is defective? If the blower motor resistor pack is bad the blower will not work. Have you applied 12 volts directly to the blower motor to verify it is bad? I have not replaced a blower motor on your particular car but it is usually a labor intensive repair. Depending on where you have it repaired the cost could be as little as $150 and up. Hard to say without actually doing it. Replacing the Resistor Pack is a fairly easy repair, so hopefully that is your problem.
Posted on Dec 15, 2009
Tips for a great answer:
Jan 30, 2013 | 2000 Buick LeSabre
May 21, 2010 | 1990 Buick LeSabre
May 02, 2010 | 1990 Buick LeSabre
Aug 23, 2009 | 1990 Buick LeSabre
May 05, 2009 | 2001 Buick LeSabre
Apr 28, 2009 | 1990 Buick LeSabre
100 people viewed this question
Usually answered in minutes!