Question about Dodge Avenger

Open Question

How to put on serpentine belt 2008 dodge avenger

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6 Answers

SOURCE: dodge avenger 2008

It depends on who you go to and if you want it done right. I went to the Dealership and had them put front brakes on my 2008 Dodge Avenger and it has been in the shop every 2-4 months since then for front brakes. They replaced the entire front brake system and my 08 Avenger is still eating brakes. I finally took it to a friend who owns a auto repair shop he replace the rotors which are total about 115.00 for each from AutoZone and replaced the brake pads for 50.00 so it cost me just parts 155.00 and my Avenger is running smoothly since haven't had problems with the brakes since. Go to Midas and let them change it for roughly 89.00 avoid the dealership at all cost they can run 200.00-500.00 depending on if it is just the brakes pads or if it is the rotors and pads.

Posted on Jun 02, 2009

Ad
localwonder
  • 6784 Answers

SOURCE: diagram for a serpentine belt replacement for 2000 avenger dodge

HI. i have posted the diagram requested below.

7109f62.jpg

Posted on Aug 24, 2009

Testimonial: "This was exactly what we needed, Thank you so very much. "

c17hydro
  • 2984 Answers

SOURCE: 1998 Dodge Avenger serpentine belt issue

What size of motor, do you have a/c and which belt are you replacing? Not sure about your engine size since you did not list it so please pick the applicable motor:

Sebring Coupe And Avenger (2.5L VIN N Engine)

  1. Disconnect the negative battery cable.
  2. Loosen the tension pulley locknut.
  3. Rotate the adjusting bolt to decrease the belt tension.
  4. Remove the drive belt from the engine.
To install:
  1. Position the replacement belt around the pulleys, making sure the belt routing is correct.
  2. Adjust the belt by rotating the adjusting bolt until the correct tension is reached. Refer to the procedure earlier in this section for belt adjustment.
  3. Once the desired tension is reached, secure the locknut. Recheck the belt tension.
  4. After the belt is installed and adjusted properly, tighten the locknut to 17 ft. lbs. (23 Nm).
  5. Connect the negative battery cable.

2.0 DOHC

Power Steering Pump And A/C Belt
  1. Disconnect the negative battery cable.
  2. Loosen the tension pulley locknut.
  3. Rotate the adjusting bolt to decrease the belt tension.
  4. Remove the drive belt from the engine.
To install:
  1. Position the replacement belt around the pulleys, making sure the belt routing is correct.
  2. Adjust the belt by rotating the adjusting bolt until the correct tension is reached. Refer to the procedure earlier in this section for belt adjustment.
  3. Once the desired tension is reached, secure the locknut. Recheck the belt tension.
  4. After the belt is installed and adjusted properly, tighten the locknut.
  5. Connect the negative battery cable.

Posted on Oct 29, 2009

  • 63 Answers

SOURCE: 2008 Dodge Avenger check engine light

Not sure if this will work for you but worth a shot. I own a 2005 dodge neon. I know the ecu's are different but maybe dodge was smart and made all the cars this way. Insert you key into ignition. Turn key forward until you are at the last position right before the car starts to crank over. Repeat this for a total of three times then on your digital odometer display, you will see a set of numbers displayed. this will be your code for the malfanction(s) that set your check engine light. Like I said, it might not work on your car but give it a shot. If not, rent an obdII scanner and get your codes. Then you know where to start looking to fix your problem.

Posted on Dec 17, 2009

  • 31 Answers

SOURCE: i need a diagram of

There should be a diagram under your hood on the radiator support.

Hope this helps

Posted on Aug 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 dodge avenger serpentine belt diagram


Is it not on top of your radiator area, or underside of hood? What engine?

Apr 19, 2013 | 2008 Dodge Avenger

1 Answer

2008 avenger engine light won't go off after replacing serpentine belt


Belt has nothing to do with any OBD Code Check Lights,
it is just an accy drive belt

Check for codes & diagnose what ever area they take you to

Jul 18, 2012 | 2008 Dodge Avenger

2 Answers

How do you put on a serpetine belt on a 2008 dodge avenger


ledsled378_142.jpg
.............................................................................................................................................

Aug 06, 2011 | 2008 Dodge Avenger

1 Answer

Wanna replace power steering pump on my 2008 dodge avenger and wanna know where the bolt is to loosen the tension belt


It's spring activated. Look for a pulley at the end of a lever. That's the tensioner pulley. Put a wrench/socket on it and move it away from the belt. Use caution, as I stated, it's spring loaded/activated. That's how it keeps constant pressure on the serpentine belt. Check under the hood for a routing diagram for re-installation. Or draw a quick sketch.

Hope this helped. I wasn't more precise, as I don't know which engine/options you have in it.

Mar 06, 2010 | 2008 Dodge Avenger

1 Answer

Putting serpentine belt back on


if you go to google.com and put in the year of your car and what you need, it will come up with a diagram.

Feb 18, 2010 | 2008 Dodge Avenger

1 Answer

How to put a belt on a Dodge avenger


Welcome to fixya release the belt on the tensioner and it should come right off., If you need anything go to my www.collisionrepairadvice.com

Aug 11, 2009 | 1997 Dodge Avenger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...