Question about 1996 Plymouth Voyager

1 Answer

Blower fan wont work replaced it and control panel allso replaced bloerfan relay for the 3 speed on firerwall

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sounds like a ground problem. I had one that I ran a new ground for and it worked fine. Also check for power to the switch and blower motor.

Posted on Nov 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to trouble shoot front blower


There are several reasons for a blower to stop working. Does it work on ANY speed? Does the AC compressor lamp or any of the vent control LEDs still work when using the AC controls? Do ANY of the speed for the blower work or are they all dead?

1st, you wanna check your fuses. There will be fuses in the underhood fusebox marked blower or heater fan, check and repalce as necessary. Also, if the earlier check for working LED bulbs on the AC control panel showed some or all lights dont ever turn on when engine is running, you may have problems with the control system.
if the fuses are good, now you need to test parts. there is a blower motor speed control aka blower resistor that frequently fails on most cars. It is the part that carries the current for all speeds of the blower and regulates speed when commanded. It has to absorb the excess energy to lower speeds and it tends to get very hot and burn out as a result. If it has failed, there will be power IN on one of its wires, and no power OUT on any others. If you have no multimeter or testlight to check things like this, Id recommend taking it to a certified mechanic.
If the control lamps all work that means controls have power, if the blower resistor has no power, fuses or blower relay are the most likely cause. if the blower resistor has power but still no fan, most likely your fan has failed. as a general rule, I replace fans and blower resistors as pairs. fans tend to last longer, but they also get more demanding with age (kinda like people) and that extra demand will burn out the newer resistor much faster than when the fan was newer. it can be alot of time and money to change a blower TWICE, so to be sure it wont fail again, test current, or simply replace the blower fan if it is determined a resistor has failed. (a good fan in theory shouldnt draw enough amperage to burn out a good resistor, EVER, so if the resistor burns, the fan is typically drawing too much power, and even though it works "fine", it will burn the next resistor in a short time as well.).

Feb 24, 2015 | 2005 Dodge Caravan

1 Answer

1992 chevy C1500: Heat works on low speed, no medium, and high only works intermittantly.


On any other vehicle it sounds like the blower fan switch.
The fan switch provides power or ground to the resistor and there would be a high speed blower relay to bypass the resistor.
But in your case the fan switch is part of the controller.
I don't have a diagram for a 92 but the 94 model shows relays for low medium and high speeds. Each relay gets power from a fuseable link. The high relay gets power thru the low relay if the low relay is not engaged.
If you have the model with 3 relays you may need to check them.

Feb 01, 2013 | 1992 Chevrolet C1500

1 Answer

Subaru 2006 Tribeca B9 HVAC Transistor replacement


The central element is the auto A/C control module which gets its power through 15A fuse 7 and 7.5A fuse 31 in the fuse and relay box (F/B). The F/B also contains 15A fuse 22 which supplies power to the A/C control panel and the auto A/C control module. The main fuse box (M/B) supplies power to the 30A SBF HOLDER fuse and through it to the blower fan relay. The auto A/C control module Input from the A/C control panel is processed to produce output that closes the blower fan relay and turns on the blower fan motor at a speed determined by the blower fan controller. There you have it - not a transistor in the bunch!

Oct 15, 2012 | Cars & Trucks

1 Answer

Blower motor resistor


Locate the blower motor and look around the outside and close to the motor for a 2-by-3-inch plate held on by two or four small screws. There will be an electrical connector plugged into it with five or six wires, depending on the vehicle type and heating and air conditioning type of control panel.
Test the resistor before replacing it. It is always recommended to test any electronic unit before replacing because there are a multitude of things that could cause the same symptoms. It only takes a few minutes and can qualify the assumption that a part is bad. It will save money to replace or repair the right part the first time.
Check the speeds by turning the fan conrol to all positions. Take note which fan speeds work and which speeds do not work. If the fan works only on one speed the blower motor resistor is very likely bad.

Check the fuses if the fan speeds do not work. The fuses for the interior heating and air conditioning fan are usually under the hood in the fuse and relay center. If the fuse looks good, then take it out and turn the ignition key on and use the volt meter set at 20 volts DC. Check to make sure that there is voltage to the fuse. If not, check for an open circuit to the fuse.

Check the relay to determine if there is power at the fuse. The relay should have two of the four terminals showing power. With the key on and the fan turned on, remove the relay and put it back in, listening for it to click. If it does not click, then replace the relay.

Check the voltage at the electrical connector on the blower motor resistor to see if the fuse and relay are good. Make sure that power is present at the connector with the key on and the fan switch on. There should be power at two terminals of the blower motor resistor. If only one terminal has power, replace the resistor. If two terminals have power, replace the blower motor itself. Remove the screws and unplug the connector to remove the blower motor resistor. Put the new one in its place by screwing it back in and plugging in the wiring connector.

Honda Parts.




May 28, 2012 | 2003 Ford Explorer

3 Answers

Where is the blower motor relay on the 1994 Ford Econoline. The fan is going one speed - SLOW. I replaced the blower motor, because it was squealing, but that never solved the problem. I'm thinking it's...


On your vehicle, if it works on low speed, that eliminates the fuse, the blower motor relay and the blower motor resistor. All of the parts of the resistor must bee good for it to work on low. The relay supplies power to the motor and the controls provide the ground, so if the motor runs at all, it is not the relay or the fuse. The only thing left is the switch. Fords are bad about burning the wire connector that conects to the switch. You will most likely have to replace the switch and the connector. Both of these parts are widely avaiable at most aftermarket parts stores.

Jan 15, 2011 | Ford E-Series Cars & Trucks

4 Answers

Heater on my envoy only works on 3-4 setting, could that be the switch.


Thanks for the opportunity to let me help. The blower control switch in your vehicle also uses a blower relay. This relay is generally located on the firewall on the passenger side near the heater fan. You can also look in you vehicle owners manual for the location of the blower relay, it may be also be located in the fuse and relay box under the hood. Generally speaking if the highest setting doesn't work on a GM vehicle it is a high blower Relay. This item is not expensive and can be purchased at most all you local Auto parts stores. If you have a Napa, Orielly's, or AutoZone these stores will also likely help you in the location if you are unable to locate this relay. Here is a general picturepepsiman1967.jpg The installation of this relay is either to remove from the fuse box, or if located near the heater fan housing then you will need to remove the mounting screws, remove the wiring clip, then reverse to install. I hope that this has helped you. D.R. Wilkins

Nov 05, 2010 | 2004 GMC Envoy

3 Answers

I only get the fan to work on high speed, the lower speeds do not work


Hi!!
The Blower Motor Resistor also called Manual Temp. Control resistor), is fried, replace. The price with floor console $25 and without floor console $65. here is a pic.
87b9810.jpg

the resistor is located on the blower motor housing, fastened by two screws. It is the part where the electrical plug connects, the plug on the pic. goes to the blower motor.
A HELPFUL - 4 THUMBS rating for this solution would be greatly appreciated. Thank you for using FixYa.

Oct 19, 2010 | GMC Yukon Denali Cars & Trucks

1 Answer

My air conditioner/heater blower will not work on the 4th setting. Setting 1,2, and 3 do work. I have replaced fan speed switch and replaced the resistor. Any ideas?


You'll have to find the correct wiring diagram in order to trace down the fault in your system.. Once you obtain the wiring diagram you'll be able to see what else beside wire is between the #4 speed setting and the blower motor. My guess is you might find a high speed fan relay is triggered from the #4 fan switch setting, applying full battery voltage to the blower motor. If locating the appropriate diagram proves to be difficult you can try looking around the underhood and passenger compartment fuse panel to find a relay. Keep in mind not all relays are always in fuse boxes which makes the diagram important.

Sep 10, 2010 | Pontiac Bonneville Cars & Trucks

1 Answer

Fan only works on 4 and 5 settings? Is this a


Hello,

I have a 2003 Chevy Cavalier. The HVAC airflow dial only works on high setting. We checked the fuse and it's o.k.

What now?  Any estimate as to repair cost? 

Thank you

Sep 07, 2009 | Chevrolet Malibu Cars & Trucks

2 Answers

2000 grand prix fan speed


i have been having that same exact problem with my 2002 grand prix for over a year now, and when my ac is on the lower setting the it doesnt work plus the headlights and lights on my dash go out. On Max everything works. i changed the blower resistor(about $35), still doesnt work. i changed all relays and fuses related to the ac, still doesnt work. i changed out the actual ac control switch in the dash, still doesnt work. i have changed everything but the blower motor and have asked every mechanic and auto parts retailer i come across and no one knows the answer. The best answer i got is that it is probably a wiring problem like a short somewhere.

May 28, 2009 | 2000 Pontiac Grand Prix

Not finding what you are looking for?
1996 Plymouth Voyager Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...