Question about Dodge Ram 1500

Open Question

How to replace a waterpump on a 2005 dodge ram 4.7L and is it easy?

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1779 Answers

SOURCE: 1997 dodge caravan waterpump replacement

OK, disconnect neg battery cable, drain cooling system, remove splash shield under right front fender for easy access to water pump bolts, loosen clamps and disconnect hoses from pump, remove drive belt, remove water pump pulley bolts, remove pulley (tip: loosen bolts on pulley before removing belt), remove water pump bolts (5) , separate from the front cover, clean the bolt threads and the threaded holes in the front cover to remove any corrosion and sealant, remove and discard o ring and clean mating surfaces, careful not to gouge or scratch mating surfaces, install new o ring into the groove, install the pump to the front cover and tighten to 105 INCH pounds, pulley bolts are 21 FOOT pounds.Good Luck! countrycurt0

Posted on Oct 05, 2008

  • 19 Answers

SOURCE: 2005 dodge ram 1500 4x4.There is a grinding noise

This sounds like a bad CV shaft. Check the boots for grease on the outside of them or torn boots the grease may have already washed out and wiped out the joints.

Posted on Feb 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 Dodge Ram 1500 with a outside temperature sensor not working. It's always reading 54 degrees C. I have tried a new sensor and that's not the problem. Any other suggestions?


Mine was the small circuit board in the overhead console. Got one from a junk yard and swapped it out with no problems. Just make sure the plastic is warm, as when cold they break real easy.

Nov 27, 2012 | 2005 Dodge Ram 1500

1 Answer

2007 dodge hemi coolant pipe rusted out


If it's threaded you can replace just that line.

Oct 13, 2012 | 2007 Dodge Ram 1500 Quad Cab Sport

1 Answer

My 2005 ram 1500 4.7 has been running progressively hotter over the last couple of months. ive changed out the thermostat, fan clutch ,and waterpump and i still cant make it 30 miles to work without it...


Remove the radiator and have it stripped and rodded out then reassembled by a radiator repairers. They can be blocked badly internally and otherwise look ok.

Aug 22, 2011 | 2005 Dodge Ram 1500

1 Answer

My air vent louvers are broken on one of my dashboard vents. Is it easily removed to be replaced or repaired.? 2005 Dodge Ram


Chances are the louver is toast. They are relatively easy to remove. Pry gently at the top and bottom of the louver with a small flat screwdriver. The two pegs holding it in place should pop free. You will probably find that one or more of the tiny plastic pins are broken.
The dealer should carry them but I am going to start looking at the junk yard first.
Hope this helps.

Mar 28, 2011 | 2005 Dodge Ram 2500 Truck

1 Answer

I have a po405 code , egr position sensor cuircuit high ,how do i change a egr valve on a 2006 dodge ram 1500?


Easy stuff my friend.use a 10mm socket and unbolt it from the head.also there's a tube and an 8mm socket can be used to remove them.4 bolts in all and replace the 2 gaskets.Erase the code if possible as well.

Dec 15, 2010 | 2005 Dodge Ram 1500

1 Answer

My oil pressure gauge is floating left to right....


I would replace the sending unit. It is an easy and cheap replacement compared to solving low oil pressure issues. If you really had low oil pressure than you would have heard noises like lifters clicking, rod knocks, etc.

Feb 20, 2010 | 2005 Dodge Ram 1500

3 Answers

Where is the egr flow sensor on a 2005 dodge ram


I just took mine to the auto part store to find out. From what they told me its the little box on top of the Hemi Engine cover. They said I have to go to the dealer to get the part though.

Apr 10, 2009 | 2005 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...