Question about Jeep Cherokee

1 Answer

How can i activate my cruise control in my 2004 grand cherokee

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 104 Answers

The cruise control switches are located on the steering wheel. When the cruise control is turned on there will be a green light luminated on the dash that says "cruise". When at the desired speed press "set" to set the cruise control at that speed.

Posted on Oct 09, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 12 Answers

SOURCE: 93 jeep grand cherokee, cruise control

Just in case you haven't got this fixed already, I just noticed on my 93, the cable from the vacuum control, (the cone shaped device on the passenger side near the coolant overflow ) was sitting against the tubes from the ac compressor, it had started to melt from me using the ac, if it melts through I am not sure if it would cause a vac leak, but if it did, you would only be able to detect it with the cruise on, not easy to check with the vehicle parked. I used a couple of cable ties to secure it away from the tube..not sure if you can tape around it to fix if it has melted.
just thought I would throw it into the mix.
j

Posted on Aug 13, 2008

  • 74 Answers

SOURCE: 2003 jeep grand cherokee cruise control not working.

it must be the part on the transmisiont that either went bad or the connections are bad

Posted on Jun 18, 2009

ZJLimited
  • 17970 Answers

SOURCE: cruise control not working

Review this information about Jeep-WJ-Cherokee-Service-Manual-PDF-08W-Diagrama-de-Cableado (Wiring Diagrams / Section 8W Page 181 (8W 33-1)

Is in spanish, but the graphics can help you.

Good luck!!!

Posted on Aug 04, 2009

  • 1 Answer

SOURCE: cruise control no go when button is pushed

I press the control switch on my 1999 Jeep cherokee. the cruise light doesn't come on and the cruise does not engage. Please offer a solution.

Posted on Jan 11, 2010

  • 1 Answer

SOURCE: 2004 jeep grand cherokee cruise control does no

try the brake switch located behind the brake pedal....had similar problem and this fixed it

Posted on Feb 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cruise control doesn't work 1995 jeep grand Cherokee laredo


being a 95 locate cruise control unit under hood & check for broking vacume hose
and replace make sure fuse is active

May 02, 2011 | 1995 Jeep Grand Cherokee

1 Answer

My Jeep Grand Loredo 2004 cruise control went out


Check the vacuum hoses it is easy to notice if one is missing or not. If that doesn't work, I'd try the cruise control switch. Hope this helps

Apr 05, 2010 | 2004 Jeep Grand Cherokee

1 Answer

2004 jeep grand cherokee cruise control does no set. Is there a bad fuse?


try the brake switch located behind the brake pedal....had similar problem and this fixed it

Feb 14, 2010 | 2004 Jeep Grand Cherokee

1 Answer

Cruise control no go when button is pushed


I press the control switch on my 1999 Jeep cherokee. the cruise light doesn't come on and the cruise does not engage. Please offer a solution.

Nov 14, 2009 | 1999 Jeep Grand Cherokee

1 Answer

My cruise control won't engage


check vaccuum hose. Mine pops off fairly regularly and causes no cruise as well asthe inability to change air controls from heat to defrost etc.

Jul 16, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Same exact problem.


Could be the plunger motor/ vaccum plunger under the hood. If the cruise light is on, the computer thinks it is working.

Jun 25, 2009 | 2003 Jeep Grand Cherokee

1 Answer

Cruise control accelerates after setting it


Most likely due to a problem with the PCM (Powertrain Control Module). You can try disconnecting (for about a minute) and reconnecting your battery which may reset this system and fix the problem. If not, you can bring your vehicle into the dealer, they will perform a diagnostics test for about $95 that will determine what the problem is. If it ends up being the PCM, it is covered under warranty for 8 years 80,000 miles.

Hope this helps.

May 12, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Leaking brake fluid + Faulty cruise control


If you see fluid at the rear of the master where it attaches to the power booster then the cylinder itself is leaking. It's not often that the container leaks.
The hissing noise is very likely coming from the power booster. This must be replaced. If cruise has a vacuum hose that connects to hose to booster it's possible that vacuum loss at booster is causing the cruise problem.If you are going to do the booster, have a good tech take a look at it first. they are expensive and you don't want to change it on my advice alone...I'm not there and can't hear it!

Mar 24, 2009 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

380 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...