Question about 1987 Toyota Supra

1 Answer

Clutch my clutch fluid has leaked over years and now after my car has sat for the winter when I applied my clutch and it sank to the floor. I was told that the problem was either the master cylinder or slave cylinder. I need to know where to start.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It could be either, look at your master cylinder in engine bay and look for leaks, if you find none look inside the car up under the clutch pedel, check for fluid seeping around where the pedel arm goes thru firewall and possibly under carpet

Posted on May 30, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Clutch travel to the floor

the brake fluid has drain out of clutch master cylinder fill with brake fluid reservoir is next to the brake master cylinder. pump pedal if spongy then bleed system with a 2 ounce syringe at slave cylinder loosen screw and force fluid to the master this will push all the air out.

Apr 22, 2014 | 2002 Honda Civic

3 Answers

My clutch is going straight to the floor and car wont go into gear

But check in see if it's just the ball joints first that's a easy fix compared to replacing the whole clutch I have a 1999 Ford escort manual and just had this problem I know all I need to know about this car make and model trust me it's your clutch nothing else You are soon to run into belt problems too keep an eye on that

Mar 29, 2014 | 1999 Ford Escort

1 Answer

Troubleshooting 92 geo storm clutch

It's time for new clutch set for your car. Good practice to always change the parts for clutch system. Clutch, pressure plate, throw out bearing.

Apr 21, 2012 | Geo Storm Cars & Trucks

1 Answer

Clutch quit working while I was driving. It goes completely to the floor & now won't go into gear. What does that sound like happened ? Pls help I'm a women w/ no family alive

Check around the clutch master cylinder for leaks. Sometimes all it needs is a few seals and it's good to go. make sure the clutch slave cylinder is full off fluid.
If you still have fluid in the system when you apply pressure to clutch, fluid will come out where the line is damaged.
Another possibility could be that the reservoir may be out of fluid (which means you have a leak that needs fixing). Some more uncommon things that can happen is having a broken clutch release bearing or fork or release cable. just my opinion, get it looked at by a garage or friend that is a mechanic or knows cars. because if you take it to the dealer it usually will be a big ripoff in $$$. good-luck and may god bless !

Sep 11, 2011 | Ford Ranger Cars & Trucks

1 Answer

1990surf clutch wont return from floor all the time wont disingage?? what the pedal ajustment free play??Ralphy

the pedal freeplay should be about a quarter of an inch. This is the area the pedal travels before the first amount of pressure is applied. have you checked your clutch fluid? if its low you should scope for leaks, check the master cylinder and slave cylinder, pull back the rubber boot and check for any fluids. i would do this only if the fluid is low. have you had any clutch work done recently?

Jan 22, 2011 | 1992 Toyota 4Runner

1 Answer

Added brake fluid when pedal went to floor,reservoir almost dry,good brakes after that pumped them up, now maybe 1 month later lent same car to friend ,said brake pedal sank to floor & red brake light...

There is diffinatly a leak in the break system and it is most likely one if not both of your rear wheel cylinders. Need to have it checked out before it gets worse and you end up in a wreck due to no brakes.

Jan 08, 2011 | 1994 Oldsmobile Cutlass Supreme

2 Answers

I have a 2000 Isuzu Rodeo in which the clutch pedal went to the floor & stayed there. Upon inspection, the clutch master cylinder was empty on fluid. I filled the reservoir & bleed the clutch...

It sounds as if you have 2 problems here.

The fact that the clutch pedal went to the floor and stayed there suggest a fault in the master cylinder. It may be that you need to overhaul the master cylinder.

Overhaul kits are available at less cost than a clutch master cylinder:
0results for isuzu rodeo clutch master cylinder overhaul kit

The grinding noise ... A grinding noise would be caused by either the gear not engaging properly because of the defective clutch.

Or, if it is more of a squealing noise - that may be the clutch release bearing at fault.

Are you absolutely sure that your entire clutch unit - pressure plate, driven plate and release bearing aren't worn?
116results for isuzu rodeo clutch

Mar 14, 2017 | 2000 Isuzu Rodeo

2 Answers

I have a 1995 Isuzu Rodeo 2WD, 5 SP 240K miles, with original factory clutch still. My question is; Why during the winter months my Clutch Pedal loses tension and it goes (sank) all the way to the floor...

With that much play on the clutch you will need to replace the clutch and in the mean time you can float the gears by matching your rpms and your speed you may scratch a little but you can get it to the shop however its nor recommended to float gears because you can damage the gears if you do it too much.

Dec 10, 2009 | 1995 Isuzu Rodeo

2 Answers

92 Eagle Talon Clutch pedal won't return fully

fill your clutch fluid, it tells you what kind of brake fluid to use on the cap, and then bleed your clutch system as you would your brakes, the bleeder is located on the slave cylinder i believe

Oct 04, 2008 | 1992 Eagle Talon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides