Question about 1995 Mazda 626

1 Answer

The headlights on my 1989 mazda 626 work fine,but the high beams dont work at all.Can you help?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 128 Answers

Replace the globes , the high beam and low beam are in the same globe , i have berfore had this happen , when replacing dont let any part of your fingers or hands touch glass part of bulb , or you may find you will be doing this again very shortly.
any finger print will cause a hot pot on globe and cause future failure .

if you remove a globe you may visually look at it and see if one of the to globes springs are broken , or is there is any discolourment in the globe itself , just change the one that is easiest to get first and test , then if that works fine , then you wont have to check any futher wiring problems.

but i am sure this will be the reason for no high beam , unless you high beam switch on light swith lever arm is faulty .
but globes are cheap so begin there first.. hope this is helpful

Posted on Oct 09, 2010

  • robertebenal Oct 09, 2010

    I already checked the bulbs,there fine.I think it may be a fuse or a relay,but I dont know where to find the high beam relay or fuse in this car.I don't have an owners manual.I found a fuse box under the dash,and one under the hood,but nothing indicates high beams.

  • cals-studio Oct 09, 2010

    usually i think if it were a fuse you would have no lights at all , i think the relay is more likely , i am sorry i dont have the same vehicle to tell you where it is , i guess you have endlessly tried to search for a manual , have you tried loooking in auta parts shop for a maunal and have a quick flick through book to see if you can see exactly which relay it is ,?
    i usually swap the same kind around and see what stops working , or remove and see what it belongs to .. hope this is of some assistance

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No headlights on mazda 626 1992


the high voltage may have burnt out your headlight on and off switch. this switch is the headlight knob or button you use to turn on your headlights

Oct 20, 2012 | 1992 Mazda 626 2.5

1 Answer

1996 mazda 626 / headlight won't turn on without dimmer switch on high. any solutions?


So what you are saying is you only have high beam lights ?
The problem could be the dimmer switch or the headlight switch, or a relay.
Have you checked for power at the dimmer switch and the relay ?

Aug 15, 2012 | 1998 Mazda 626

1 Answer

Main beam not working on x reg mazda 626 full beam working ok


low beam burnt out,replace low beam bulb,if only one headlight,replace bulb

Dec 31, 2010 | 2000 Mazda 626

1 Answer

Headlight stop working but high beams work only when you flash them 95 mazda 626?


It could be the lamps are burned out. The high and low modes function on two separate filaments, so the high will still work even when the low is burned out.

Regards,
matt

Sep 15, 2009 | 1995 Mazda 626

1 Answer

High beams stick on when i use the turn signal


turn signal/high beam switch is bad

Jul 12, 2009 | 1989 Mazda 626

1 Answer

Headlights and high beams suddenly quit working Fuse box has no cover so I can't tell which fuse to check. Parking lites work fine.


well you have to check the one at a time to see which one has blown if any.I think you have a switch problem if high beam as well as low are not working

Jun 12, 2009 | 1999 Mazda 626

1 Answer

I have a mazda 1994 626, flashing the full beam is fine however when i switch the lights to full beam nothing happens. can anyone make anu suggestions please.


Sounds like the high beam switch in the steering column bad. Might be a bad/broken contact on teh end of the switch

Feb 22, 2009 | 2002 Mazda 626

1 Answer

Headlights


hi thank you your help, id like to do the work myself. how would i go about thatg exactly?

Feb 22, 2009 | 1998 Mazda Protege

1 Answer

The headlights in my `97 Mazda 626 are out


wire harness on both low beams.

Feb 15, 2009 | 1997 Mazda 626

Not finding what you are looking for?
1995 Mazda 626 Logo

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...