Question about 2000 Mitsubishi Eclipse

1 Answer

Tune up I need to remove the intake manifold to get to the opposite three spark plugs. How do I go about doing this?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

Just remove all the bolts and hoses atached to the upper intake or go to the autoparts and buy a book for this specific car

Posted on May 30, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I was told that in order to change the spark plugs on my Nissan Maxima, the shop would have to remove the intake manifold to an extra cost of 200.00. Is it necessary to remove the intake manifold to change...


This is possibly true, especially if you have a 6 cylinder. They don't actually remove the whole intake from the motor, there is a section of the intake system that can be removed fairly easily and then the plugs can be accessed. Unfortunately, this design was more to push the price of a tune up higher than a needed design change, at least in my opinion. Since you have to remove that part most people are more inclined to take a vehicle to the dealer to replace spark plugs instead of doing it themselves and as you know, the dealership prices are higher than anywhere else and the mechanics have the same qualifications other mechanics have.Typically no seals need to be replaced when this is done but it does take more time and that is where the dealership makes it's money.

May 14, 2011 | 2000 Nissan Maxima

2 Answers

I need to know how to change the back three spark plugs on my 2008 ford edge , do i remove the manifold.to get to them, is it safe


Yes, you will have to remove the intake manifold. If you are mechanically inclined, it's not that hard. Looks complicated because of all the wires and hoses. Just take your time, keep track of everything you do, take notes if you have to, so everything goes back together the same way it came apart. Since you are going to all this trouble be sure you buy a premium spark plug. I wouldn't use Champion or Ford products. NGK Iridium would be my choice if they are available.

Jan 01, 2011 | 2008 Ford Edge

1 Answer

I have a 2000 montero Sport. How do I get to the other spark plugs for a tune up? Do I have to remove the intake manifold?


Hello,
In order for you to get to the other spark pluggs,the intake manifold must be removed,that's the only solution.


Take care..

Aug 07, 2010 | 2000 Mitsubishi Montero Sport

1 Answer

Tune up


NOPE TUNE UP CHECK ALL ENGINE FLUIDS.CLEAN INSPECT BATTERY.TURN OFF RADIO FIRST BEFORE REMOVING BATTERY CABLES SO YOU WONT LOSE CODE.CHECK THE COOLING SYSTEM.CHECK ALL HOSES.CHECK FUEL SYSTEM.AND AIR FILTER.CHECK DRIVE BELT OR BELTS.REPLACE SPARK PLUGS + WIRES.YOU DONT NEED TO REMOVE INTAKE AND EXHAUST MANIFOLDS.

Apr 11, 2010 | 2004 Kia Sedona

1 Answer

How do you replace the spark plugs on a 2005 chrysler 300? I can see three plugs with coils over them but where are the ones for theother side fothe engine? Are they under the intake?


YEP YOU HAVE TO REMOVE INTAKE AND REMOVE IGNITION COILS ON TOP OF THE SPARK.BESURE TO USE SPRAY COMPRESSED AIR AROUND THE COIL AREA AND SPARK PLUG TO REMOVE CONTAMINATES FROM AROUND SPARK PLUG TUBE.

Feb 27, 2010 | 2005 Chrysler 300

2 Answers

Spark plug location in a 2001 ford escape


Need to remove upper intake manifold to reach valve cover close to firewall.
1) The location of spark plugs 456 are under the plastic shield in front of the engine. It takes an 8mm socket to remove the three bolts holding the shield once the shield is removed you will see a coil for each spark plug. Use the 8mm socket and remove the coil and rubber boots. You will now see the spark plug (note there are not any spark plug wires).
2) The location of spark plugs 123 are located to the rear of the eng. You have to remove the air intake manifold in order to get to the spark plus. Remove the throttle wire then remove the other items on top of the intake manifold.

Nov 16, 2009 | 2001 Ford Escape

2 Answers

I keep getting a notice that the #2 and #4 cyclinder is misfiring. I went to change the plugs, but could not locate them from the top of the engine. Where are the plugs located at?


Need to remove upper intake manifold to reach valve cover close to firewall. 1) The location of spark plugs 456 are under the plastic shield in front of the engine. It takes an 8mm socket to remove the three bolts holding the shield once the shield is removed you will see a coil for each spark plug. Use the 8mm socket and remove the coil and rubber boots. You will now see the spark plug (note there are not any spark plug wires). 2) The location of spark plugs 123 are located to the rear of the eng. You have to remove the air intake manifold in order to get to the spark plus. Remove the throttle wire then remove the other items on top of the intake manifold. 3) Loosen all the bolts holding the manfold. 8mm socket-- I think three in front and three in the middle. Remove the EGR valve mounts so you can slide the manifold out. Disconnet all vacuum lines from manifold and the air filter inlet closet to manifold. Just take a general look and ensure you have all wiring and tubing disconnected then slide the manifold off the eng and EGR valve. NOW MAKE SURE you cover all intake holes (leading into the engine) with paper towels to prevent droping screws etc into the engine. Then follow step 1 above

Oct 28, 2009 | 2001 Ford Escape

1 Answer

I want to change the spark plugs in my 2001mazda tribute


See the tips section of my profile on Fixya. I have complete instructions on how to change the plugs and coils.

Jul 05, 2009 | 2001 Mazda Tribute

1 Answer

2001 mazda tribute spark plug change


can 't you remove the coils insted of the intake ? It is much easier.

Sep 28, 2008 | 2001 Mazda Tribute

Not finding what you are looking for?
2000 Mitsubishi Eclipse Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...