Question about 1997 Plymouth Neon

1 Answer

WHERE IS THE WATER BUMP - 1997 Plymouth Neon

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Behind the timing belt cover. This is at the passenger side of the engine.

Posted on Mar 20, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 Isuzu rodeo dies when you hit bump starts back immediately


Is it setting any fault code in the Powertrain computer?

Oct 07, 2016 | 2000 Isuzu Rodeo

1 Answer

How do i get bolt off harmonic balance impact wont fit unless i remove radiator dont wanna do that


one method I have used before...
put the socket on a breaker bar... then bump-start the engine...
bump-start... have an assistant turn the engine over and quickly turn it back off... this will use the torque of the engine to break the bolt free.
not the best solution I know. Yet, it should save you from having to remove the radiator.
Stubborn Crank Pulley Bolt Removal Procedure 2 Methods Pick Your Weapon

d079e1dd-1b57-403d-9dd7-5532bc133437.jpg

Oct 29, 2014 | 2002 Chevrolet TrailBlazer

1 Answer

Water gurgling in heater, heat is warm, air is very light coming out of the vents, sometimes air goes cold then comes back warm.. a bump will make it go cold


f348184e-f64b-47f5-acd6-456139beaab7.jpg

it's look like the a/c evaporator is block by dirt,oil look at it ..It should be clean as this one

hope it helps

Apr 04, 2014 | 2000 Chevrolet Blazer

2 Answers

I have a 2007 dodge caliber. The car has only 47,000 miles and when I bought it in February 2013 it had 37,000. Ive only had the car for 8 months and everything was perfectly fine until I went over a...


Im not to sure if this model is fitted with accident stop. usually if you have had a bump it turns of the engine. until the code has been rest. sometime if it is this type you can take the battery off and leave it off for 12hrs and re put back on. and it resets. but not herd of them doing this. you see the bump could of lost or broken a sensor and driving with the case of it water may have got in to it and that is why it has taken this long for the problems to occur. would first start looking on the side the bump was. and check every sensor. abs is the sensors on the wheels.

Oct 13, 2013 | Dodge Caliber Cars & Trucks

1 Answer

Leaking water pump has gone out


Man I feel for you. Whatever you do do not bump the starter when the belts are off the water pump. Its a real pain of a job to replace that pump and I would highly suggest you let a professional replace it if its an Eclipse. WebRepcurrentVotenoRatingnoWeight

Apr 08, 2013 | Mitsubishi Cars & Trucks

1 Answer

1993 mercedes 190e 2.3/a bump bump bump when i aceelerate


Sounds like a driveline type issue. Check carrier bearing and flex discs.

Jul 13, 2010 | 1993 Mercedes-Benz 190

2 Answers

I went through a huge puddel and the car stoped and the engine wont spin


Sounds like there is water in the engine. First check the oil level, if it is over full you have water in the crankcase and will need to drain the water form the oil pan. Next you will need to remove all of the spark plugs because it sounds like it is hydrolocked. with the spark plugs removed spin the motor over with the starter and after a bit of that, most of the water should have cleared form the cylinders. once you get it running, go over all of your fluids looking for anything overfull, indicating water intrusion and change anything suspect.

Sep 27, 2009 | 2003 Chrysler PT Cruiser

1 Answer

Overheating


Change thermostat.

Dec 24, 2008 | 1999 BMW 318 ti

1 Answer

Intermintant backfire after hittig bump hard to start poor miladge


Almost sounds like ignition problem... Hitting bump causing it to short out (turn off) for a second then restart can produce a backfire & hard to start. Bad gas (water in it) will cause backfire and hard to start. I would start with checking all plug and wire connections, putting in a good gas additive and water dryer. I your are injected I would Clean them up also... Try these out and go from there...

Jun 26, 2008 | 1995 Chevrolet Monte Carlo

Not finding what you are looking for?
1997 Plymouth Neon Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...