Question about Ford F-150

Open Question

Where is the knock sensor located on a 4.2L F-150 engine?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tripletauto
  • 1450 Answers

SOURCE: Where is the location of the knock sensor for a 2005 HD 2500 6.0

HAS TWO KNOCK SENSORS they are both under intake in valley of engine. remove intake and will see two black grommets they are under those best to replace both at same time

Posted on Jan 26, 2009

Toyota Guy
  • 42 Answers

SOURCE: Location of knock sensor on 1994 toyota 22vre engine

The Knock sensor on a 22re is located under the intake manifold on the engine block. to the upper left of the oil filter. With is the passenger side of the engine. I believe it is yellow in color. Not do be confused with the oil pressure sensor which is close by. The knock sensor has a larger electrical connector. Good luck it can be hard to get to.

Posted on May 06, 2009

  • 8 Answers

SOURCE: trying to locate where the knock sensor is located on the engine.

on my 1990 gmc its right be hind the starter its round and has a one wire plug becarful some have left hand treades and coolant willbe comn out i would do it while it was cold

Posted on May 31, 2009

ronaldo_ross
  • 1056 Answers

SOURCE: Looking to replace honda pilot knock sensor

These knock sensors are hard to get into. If thats a V6 it is underneath the intake manifold. make sure you cover the intake port when you take it apart, so a screw or a bolt don't accidentally drops in there.

Posted on Jun 28, 2009

abauto
  • 353 Answers

SOURCE: where is the knock sensor located on a 2001 subaru

When facing the engine it is in the rear right hand side.

The knock sensor is a piezo electric crystal, when they go bad the must be replaced.

Looks similar to these

8f8cf6b.jpg

Posted on Sep 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is a knock sensor located ona 1989 ford f-150 302 motor


Located in the engine block behind the intake manifold. Not real easy to get at

Apr 05, 2015 | Ford Cars & Trucks

1 Answer

2009 f150 5.4 bank 2 knock sensor location?


It is located underneath the intake manifold.
25618954-r5jmwje1ahfciumuixfstfta-1-0.jpg

Mar 31, 2015 | 2009 Ford F-150

1 Answer

Knock sensor location on an 85 ford f 150 302 f. i. engine


Hear its hard to find a replacement, but here is a picture that should help with the location.:
a2a08421-f51f-4ae7-9f1a-758346f7e43a.jpg

Dec 06, 2013 | Cars & Trucks

1 Answer

I'm wondering whether on my 2003 (B6) S4 4,2l V8 cylinder n. 4 is the fourth one (front to rear) on left bank or the second on the right one. This just to understand the real firing order. Thank...


Firing order for 2003 (B6) Audi S4 4,2l V8 engine is: 1 - 5 - 4 - 8 - 6 - 3 - 7 - 2
Cylinder no.# 1 is first one from right front side of the car, and cylinder no.# 4 is the fourth one (front to rear) on the right bank of cylinder block. See picture below:

tdisline_88.jpg

Dec 08, 2010 | Audi S4 Cars & Trucks

2 Answers

Where is the knock sensor located on my 92 Jeep Cherokee 4.0L straight 6 4WD?


I don't see the knock sensor on the 4.0L engine. --- COMPONENT LOCATIONS Fig. 1: Electronic engine control component locations - 2.5L engine shown 91074g07.gif
Fig. 2: Overhead view of the (A) automatic idle speed motor, (B) MAP sensor, (C) crankshaft position sensor wiring harness, (D) air temperature sensor, and (E) throttle position sensor - 1992 Cherokee with the 4.0L engine shown 91074p15.jpg
Fig. 3: Electronic engine control component locations - 4.0L engine shown 91074g08.gif
Fig. 4: Electronic engine control component locations - 5.2L and 5.9L engines (Part 1 of 2) 91074g05.gif
Fig. 5: Electronic engine control component locations - 5.2L and 5.9L engines (Part 2 of 2) 91074g06.gif
prev.gif next.gif

Sep 30, 2010 | 1992 Jeep Cherokee Briarwood

1 Answer

Location of knock sensor on a 1998 Saturn 4 cylinder


A knock sensor is threaded into the engine block and is supposed to sense when the engine starts to ping or spark knock and reduces the ignition timing accordingly.The knock sensor is located on the side of the engine.
  • Turn the ignition OFF.
  • Raise the vehicle.
  • Disconnect the knock sensor harness connector.
  • Remove the knock sensor attachment bolt and the knock sensor.

  • Important: The larger metal contact area of the knock sensor MUST be toward the engine block. DTC P0327 may result if the sensor is installed backwards.

  • Install the knock sensor and attachment bolt with the larger metal contact area toward the engine block.

  • Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

  • Sep 22, 2010 | 1998 Saturn SL

    3 Answers

    Knock sensor 1996 v6 3.3 nissan pathfinder


    The Crankshaft Position Sensor is located: Under hood, driver side, front engine area, mounted rear of crankshaft pulley
    The Knock Sensor is located: Under hood, center, front engine area, below intake manifold, mounted on block

    Jun 14, 2009 | 1996 Nissan Maxima

    2 Answers

    Location of knock senor on 97 maxima se


    Your knock sensor is located Under the hood, center, front engine area, below intake manifold, mounted on block.


    A defective knock sensor may cause engine detonation or reduced spark advance and fuel economy. When a knock sensor is removed and replaced, the sensor must be tightened to its specified torque. If the knock sensor is installed tighter than it should be, it may become too sensitive and provide an excessively high voltage signal, resulting in more spark ****** than required. When the knock sensor is installed looser than it should be, the knock sensor signal will be lower than normal, resulting in engine detonation.

    To replace the knock sensor:
    • Disconnect the knock sensor wiring connector.
    • Then, unscrew the sensor.
    • Remove the knock sensor.
    • Reverse the procedures to install the part.

    May 15, 2009 | 1997 Nissan Maxima

    2 Answers

    Location of knock sensor on 1994 toyota 22vre engine


    The Knock sensor on a 22re is located under the intake manifold on the engine block. to the upper left of the oil filter. With is the passenger side of the engine. I believe it is yellow in color. Not do be confused with the oil pressure sensor which is close by. The knock sensor has a larger electrical connector. Good luck it can be hard to get to.

    Apr 10, 2009 | 1994 Toyota Pickup

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    136 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    fordexpert

    Level 3 Expert

    5495 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...