Question about Volvo 960

1 Answer

I changed the water pump and all the belts and now it wont start.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 81 Answers

If you changed the timing belt and didn't mark the pulleys, you are done. Take the car to a repair center. It sounds like the timing is off.

Posted on Oct 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just changed the water pump on a 2005 dodge neon and now it wont start. What could it be


You're not giving much to go on. Is it a 2.0L or a 2.4L?
You say it won't start. Does it turn over and not fire, or does it just sit there and do nothing when you turn the key?

Both engines require you to remove the timing belt in order to change the water pump. The 2.0L is definitely an interference engine, and I'm not sure about the 2.4L. But if the timing belt was not re-installed properly, it will result in a no-start condition since the valves will not be in sync with the pistons and spark. Best case scenario you correct the issue and are good to go. Worst case scenario is that if the belt is out too far, you bent valves and have to service the head(s).

May 31, 2016 | 2005 Dodge Neon

1 Answer

I'm attempting to do a timing belt change on my 2004 Chevy Aveo. The problem is when I took off the old timing belt I forgot to loosen the tension using the water pump. When I tried to install the new...


Yes,there is a special wrench that fits the water pump. You have to loosen bolts on pump and put wrench on pump and turn pump to get belt on. Then tighten pump till marks line up on tensioner,then tighten the pump back down. Be sure to roll the engine around twice and recheck timing marks on crank and cams.

Mar 12, 2015 | 2004 Chevrolet Aveo

2 Answers

Changed water pump now wont start battery is charged


If water pump is run by timing belt, the timing will need be reset prior to start up. Make sure timing is adjusted using the timing marks from factory. Check manual to determine timing mark locations.

Jan 20, 2013 | Pontiac Cars & Trucks

1 Answer

Car wont start


Check belt timing adjust.

Mar 29, 2012 | 1994 Buick Roadmaster

1 Answer

Car starting troubles 1990 ford laser 1.3


when you took the belt off you probably changed the timing, take off the belt and adjust it just to be sure.

May 14, 2010 | Ford Laser Cars & Trucks

1 Answer

I need directions to change my water pump


drain engine coolant.relieve belt tension .and remove the drive belt.remove upper fan shroud.remove fan or fan and clutch assembly.remove water pump pulley and coolant hoses from water pump.remove water pump bolts.then remove pump from engine.pay attention to bolts location because they are different lenghts.clean water pump gasket mounting surface dont scratch .or pump gasket wont seal and leak .apply sealant to water pump bolts.install water pump with new gasket.if gasket paper put a sealant on it.torque water pump bolts to 30 ft lbs.if you got a 2.2L engine torque water pump bolts to 18 ft lbs.install coolant hoses on pump .install water pump pulley.install fan and fan clutch assembly.install the drive belt .and the upper fan shroud.fill the radiator with coolant.then run engine to check for leaks.WARNING AS A SAFETY PRECAUTION REMOVE NEGATIVE BATTERY CABLE SO CAR WONT BE CRANK BY ACCIDENT. ALSOOOO DONT FORGET TO TURN OFF RADIO FIRST BEFORE DISCONNECTING BATTERY SO YOU WONT LOSE YOUR RADIO CODE.

Jun 01, 2009 | 1999 GMC Jimmy

1 Answer

Replaced water pump nd timing belt now car will not turn over to start it trys but wont fully turn over. how do i get it to start


timing is incorrect/usually have to find #1 cyl top dead cent then use camshaft alignment marks and then reinstall belt.

May 08, 2009 | 1994 Volvo 850

1 Answer

Changed timing belt 94 civic ex 1.6, now wont start


first make shure the fireing order is correct 1 3 4 2, make shure you have the timeing set right

Apr 02, 2009 | 1994 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...