Question about 2006 Chevrolet Malibu

1 Answer

Malibu 2006 LT. The Left Front and Right Tail Turn Signal Lamps don't blink, the light just stay on but not blinking, check bulb ok. What could be the problem here? Thanks.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 81 Answers

The other turn signal bulbs are blown, or the turn signal unit itself is bad. it is under the dashboard and makes the ticking noise when the turn signal is on.

Posted on Oct 09, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm needing the wiring diagram for my 2007 Chevrolet Impala LT 3.5 tail lights.


Go to http://www.bbbind.com/free_tsb.html free wiring diagrams ! You having tail light problems ? Do you know how they work ?

They are turned on by the BCM !
Park, Tail, Marker and License Lamps
The park, tail, license, and marker lamps are turned ON when the headlamp switch is placed in either the HEAD or PARK lamp positions, or anytime the automatic light control (ALC) turns the headlamps ON. When the headlamp switch is placed in the park lamp or headlamp positions, ground from G202 is applied through the signal circuit to the BCM indicating the park lamp request. In response to this signal, the BCM applies ground through the park lamp relay control circuit energizing the PARK LP PCB Relay. With the relay energized, battery voltage is applied through the switch side of the relay, both park lamp fuses, and the supply voltage circuits illuminating the park, tail marker, and license lamps. Ground for the left front park and marker lamps is provided at G101 and the right front park and marker lamps at G100. Ground for all rear lamps is provided at G302.
Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
?€¢
G101 provides ground for the left front turn signal lamp


?€¢
G100 provides ground for the right front turn signal lamp


?€¢
G302 provides ground for the left and right rear turn signal lamps

May 03, 2016 | 2007 Chevrolet Chevrolet Impala LT

2 Answers

1999 buick lesabre my right signal doesnt blink it stays solid , my left turn signal blinks fine i have to manually blink the right side every turn , i put the hazard lights on and the front left and right...


The easiest thing for you to do would be to replace the bulbs that are on that circuit. You should have one or two bulbs with a double filament, one for the brake and turn signal and one for the tail light.
If that does not fix the problem, someone will need to check the circuit for power from the turn signal switch. It takes all of the lights on one side to make the turn signal flash.

May 16, 2013 | 1999 Buick LeSabre Custom

1 Answer

2003 Jeep liberty right front turn signal


why skip RR lamp? what does IT DO? be like 1st 1st look.
dim, out, fast?

the rapid is talking to you
it means current is wrong,
shorted, or open lines. to the right.
its the wiring
if the bulbs are like 1157 brass base bulbs
why not replace them first , they can short inside,
asking online for guessing is silly, why listen to 10 examples for this.
but is cut wires.
shorted wires.
keep i mind the blinker asks funny for both opens and shorts
its a feature, that.
low current or too much.

the acid test is connect 2 TEST bulbs in parallel to the multi-function switch output right side,
blinks ok now, bingo bad lamps or bad wiring, from there to the right side.

if the hazard fails you never said????
if rigth front is dim or dead the bulb is blown or shorted
if new bulb there , then the wires are shorted.
to it.
the only help on line worth squat is how to test and use your meter.
you can, check for voltage
you can check continuity on that line (its just 1 wire)
and check for shorts on that wire to ground (lamps pulled right side to do that, lamps read 0 ohms cold)
look for collision damage RF? behind lamp sockets?
be first.
in my book.
looking is always first. sure.


I have your SM book open now, chapter 8w-50
the haz/blink module has just 2 pins, left and right out.
pin 3 on the module runs front and rear blinks, (a fact to know)
RF is BR/RD, brown -red stripe?
all comments USA on USA forum. USA car.
ok?

the right side lamp (sidemaker) only blinks turns if parks ARE oFF

Id try 2 new blinker lamps front and 1 rear.
that be first. or test the lamp on a battery , and no not get burned fingers hot wring a shorted lamp.

wish i knew
what rear did
and what both did on HAZ
out, dim or to fast.

Mar 23, 2017 | 2003 Jeep Liberty

1 Answer

2009 Impala rear lights not working


Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
• G101 provides ground for the left front turn signal lamp
• G100 provides ground for the right front turn signal lamp
• G302 provides ground for the left and right rear turn signal lamps

The LT T/SIG and RT T/SIG fuses located in the underhood fuse block are also used by the body control module (BCM) for stop lamp operation.
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides both, a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake pedal is applied, the BCM will then apply battery voltage to the left and right stop lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM signals the transmission control module (TCM) and the engine control module (ECM) that the brakes are applied. Ground for all stop lamps is provided at G302.
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.

Did you check the fuse's. ? Wouldn't think it's a ground because right an left tail lamp Assembly's use same ground ! Did you check for B+ voltage at the bulb. with a volt meter ? Power is supplied by the BCM . Could be the tail lamp assembly

Jul 19, 2017 | Cars & Trucks

1 Answer

Front left turn signal blinking fast


If the front signal is blinking fast then theres a bulb out, check the rear to see if theres a bulb out, use the right side to see how many light are blinking and make sure the same is on the left, the main reason for fast blinking signal is a bulb is out on that side. good luck, have a nice day.

Jan 14, 2011 | 2006 Chevrolet Uplander

1 Answer

2001 Olds Silouhette - The blinker on the dash blinks quickly


NO PROBLEM TURN ON THE RIGHT BLINKER THEN WALK AROUND THE CAR MAKE SURE FRONT AND REAR BULBS ARE FLASHING... IF YOU HAVE A BULB OUT YOU WILL NOT OFFER ENOUGH OF A LOAD TO THE FLASHER... WILL CAUSE IT TO FLASH FAST... IF OK THEN MAKE SURE THE PROPER BULB NUMBER ON BULBS AND MAKE SURE CORRECT BULBS USED IN VEHICLE.... IF OK CHANGE FLASHER

Aug 31, 2009 | 2001 Oldsmobile Silhouette

1 Answer

1989 Pontiac Bonneville Left hand turn signal blinks, right hand does not. The bulbs are all working on the right side, just won't flash. I cannot find the flasher but not so sure that is it since the left...


Take bulbs out and check sockets also bottom of bulbs, park lights and tail lamps. If the solder contacts on bottom of bulbs are flat replace them.

Jul 01, 2009 | 1989 Pontiac Bonneville

2 Answers

Left rear turn signal light on my 1999 chev. s10 is not working


any increase in bink speed is direcly related to a bulb being burt out.

Jun 12, 2009 | 1999 Chevrolet S-10 Pickup

Not finding what you are looking for?
2006 Chevrolet Malibu Logo

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...