Question about 1992 Jeep Wrangler

2 Answers

Oil Sending Unit

How to change the oil sending for a 4 cylinder (5 speed)? What tools are needed?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

They sell some kind of special socket at the autoparts for oil sending units

Posted on May 30, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Where do I find the oil sending unit on a 97 chevy truck

Posted on Jan 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the oil sending unit on a 1991 Pontiac Grand Am 2.5 liter 4 cylinder automatic transmission


Hope the helps
The oil pressure sending unit can be in the block, or near the filter, the oil level sending unit if equipped is usually in the pan.

May 24, 2014 | Cars & Trucks

1 Answer

I need to replace the oil sender switch on my 2002 Buick La Sabre


first need to buy oil pressure sending unit 3/8 deep socket remove oil pressure sending unit you need teflon tap sealer for oil sending unit threads.okay to replace oil pressure sending unit.you need safe raise support vechicle locate oil pressure sending unit next to the oil filter.disconnect oil pressure sending unit wire connector then use oil pressure sending unit 3/8 socket remove the sending unit.then take new oil pressure sending unit use teflon tape white plumbers tape or use thread sealer apply to the oil pressure sending unit threads then install new oil pressure sending unit and reconnect electrical connector to sending unit.then crank engine check for oil leak if all is good lower vechicle back to ground wait several minutes check engine oil level.you good to roll.

Feb 09, 2013 | 2002 Buick LeSabre

1 Answer

How do you change an oil sending unit on a 1999 Chrysler 300M? Oil light is blinking on and off when hit brakes and riding down the road.


Replacing oil sending unit.Its just bolted with screws,you will need special tool to remove the screws.The tool is easily available at local auto part store.For more details,click the link below:--- http://technoanswers.blogspot.com/2011/10/how-to-replace-oil-sending-unit-on-1999.html --------- This should help.Thanks.Helpmech.

Oct 27, 2011 | 1999 Chrysler 300M

1 Answer

Where is the oil sending unit located on a 2002 chevrolet malibu


V6 ENGINE OIL PRESSURE SENDING UNIT LOCATION NEXT TO OIL FILTER. THE 4 CYLINDER ENGINE OIL PRESSURE SENDING UNIT LOCATION IS FRONT CAMSHAFT HOUSING ON THE LEFT DRIVER SIDE OF THE ENGINE COMPARTMENT.

Mar 20, 2011 | 2002 Chevrolet Malibu

1 Answer

WHERE IS THE OIL PRESSURE SENSOR on a 2002 ford escape


On 4 cylinder engines: The oil pressure sending unit is located in the rear of the block near the oil filter housing
On 6 cylinder engines: Sending unit is located near the oil filter housing behind the air conditioning compressor, on the front side of the block

Dec 22, 2010 | 2002 Ford Escape

2 Answers

1995 buick century-oil light came on hour after oil change


Step 1-- replace the sending unit again. Step 2--if step 1 does not cure the problem--believe the light--have the oil pressure checked with a real pressure gauge temporarily installed inplace of the sending unit. Try to not run the engine at all until this is resolved. Usually a 1 min. run at idel with no oil pressure will not damage the engine. 5 min of idle will ruin it. 1 minute of highway speed 50 MPH cruise will destroy the bearings.

Jun 19, 2009 | 1992 Acura Integra Hatchback

1 Answer

1998 toyota camry,4,cylinder, 5 speed


it sounds like your oil pressure sending unit may be plugged by whatever took your pressure down to 5-8 psi the first time. this is extremely low pressure as i am sure you know but at 30 psi your light should go off i would replace the sending unit if your oil pressure is holding 30

May 15, 2009 | 1998 Toyota Camry

5 Answers

Where is the oil pressure sending unit on 2004 dodge stratus?


per the Haynes manual for the 95-05 Dodge Stratus on the 2.0L & 2.4L DOHC 4 cyl engines, the oil pressure sending unit is located at the left end of the rear side of the block. On 2.4L SOHC 4 cyl engines, the sending unit is located at the left end of the rear side of the block. On 2.5L & 3.0L V6 engines, the sending unit is located on the oil filter housing, on the front side of the block. On 2.7L V6 engines, the sending unit is located at the left end of the rear side of the block. To access it, remove the heat shield.

Jan 23, 2009 | 2004 Dodge Stratus

1 Answer

What is a oil sending unit on 99 chevy venture van?


easy to change u just need a special tool for removed on front of motor at right of oil filter its look like a coolant sensor or a little bottle with a connetor removed the connector and take the tool to remove

Oct 11, 2008 | 1999 Chevrolet Venture

1 Answer

Low oil pressure


I believe your sending unit is located on the top of the block, towards the fire wall. You can get an inexpensive pressure test gauge and put in place of your sending unit. It should be a 1/4" NPT fitting. Does the pressure gauge fluctuate between low and high RPM? If so, chances are that your oil pump may need to be replaced.

Jun 29, 2008 | 1984 Chevrolet Camaro

Not finding what you are looking for?
1992 Jeep Wrangler Logo

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...