Cadilac cts How do I replace the fog light bulb in a 2005 cadilac cts?

How to Change the Bulb in your 03-07 Cadillac CTS Fog ...

? 4:13
https://www.youtube.com/watch?v=TaW1haYSThs
Oct 13, 2011 - Uploaded by 1A Auto Parts
How to Change the Bulb in your 03-07 Cadillac CTS Fog, Daytime ... Do you guys have video for replacing the turn signal bulb in a 2006 STS?Missing: h

Re: Reading/Clearing Diagnostic Trouble Codes (DTC) - Cadillac

cylinder 2 is at the rear of engine on the passenger side by the fire wall and cylinder 6 is at rear of motor like 2 but on the drivers side. cylinder 4 is in between them.

May be a relay issue

I've got a 2008 cts. And I just checked the lights...None of the rear lights can be changed. NONE! I do not know where these people get their info from. The only light that can be changed are the HID, fog front turn signals and the DRL's!

Front Fog Light Assembly

REMOVAL

1. Disconnect the ground cable from battery.

1. Remove the two clips and lower mudguard on side that bulb is being changed.
2. Disconnect the harness connector from bulb on back of fog lamp.

Front Fog Light Bulb

REMOVAL


1. Locate back cover on fog lamp assembly where bulb is located inside.

1. Remove the back cover.

1. Remove the spring retainer, and then detach the fog light bulb.
2. DO NOT TOUCH HALOGEN BULB!! Oils from skin will cause bulb to explode during operation.
   

I just replaced front turn signal bulb. Since all of them (signal and fog lamps) are integrated with the bumper, you have to do that from beneath. First ,turn your wheels to the max right.Inside the arch you'll see that it is covered by plastic shield.You will have to remove plastic clips on the sides of that shield.There are six of them and they are clearly visible.Be careful not to brake clips.Use flat screwdriver to pull hat first,then the whole clip can be removed with fingers.Once all six clips pulled out,plastic shield will almost fall by itself - no efforts needed to detach it. That's it - you've got the access to your signal and fog lamps.

Removing the tire and blocking the front end first with jack stands makes the access much better

2005 Forester - It is easiest to remove the fog assembly.

1. From underneath the vehicle pry out one plastic fastener to be able to bend the light weight plastic mud protector downward. You will see the underside of the fog light assembly with one 10mm bolt directly above you. Remove this bolt.
2. From the front of the vehicle unscrew one 10mm bolt at top of fog light (this is the shorter of the 2 by the way) and pry out one plastic rivet adjacent to it.
3. Carefully remove the fog assembly and disconnect 2-pin power connector by pulling up on the release. Carefully wiggle the housing out (no force req'd).
4. Unscrew the back from the housing and replace H3 bulbs. Take care not to touch the bulb while replacing.
5. Reverse to install.

Should take an hour at most.

you can change the bulb only -- Click to open expanded view ACDelco ACDelco 9045 GM Original Equipment Front Fog Light Bulb this is the replacement bulb Fog Light Replacement 2004 2012 Chevrolet Colorado 2007 Chevrolet Colorado... video shows how to replace

1. Remove the fog light mounting screw.
2. Disconnect the connector from the fog light.
3. Turn the socket about 45° counterclockwise and remove it from the housing.
4. Remove the bulb from the socket.

To Install:

1. Install the bulb in the socket without touching the glass with bare hands.
2. Turn the socket about 45° clockwise to install it.
3. Connect the connector to the fog light.
4. Install the fog light mounting screw.

in the trunk your capet is held in by plastic nuts.unsrew three or four nuts to pull capet back.then there is three or four nuts on long studs.remove the nuts only.gently pull lamp out to access the bulbs.