Question about 2004 Jeep Liberty

1 Answer

How do i fix the windshield washer system on my 04 liberty, every time we pull the washer lever it pours out of the driver side fender

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 81 Answers

You have a tube that has popped/broken off. With the hood up, have a person pull the washer lever and you look under the hood for the leaky hose/tube. Once you find it, make a common sense approach to determine how to get it connected back to where it belongs. Trace backwards from where the water should be coming out until you reach the end of the line. That is where the hose/tube needs to be connected back to.

Posted on Oct 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2004 jeep Liberty hood release is stuck it won't go back and can't get it to release hood what should I do


get it serviced...
in a shop they migth.
1: remove grills and panels in fender to gain acess to the cable
then with 3 people (yes)
1: pulls the handle.
2: other pulls side if the cable. at above found easy access point
3: other tries to lever hood open with plastic pry bar.( gently)
if that dont work the latch must be attacked directly, grills off.

Dec 17, 2016 | 2004 Jeep Liberty

1 Answer

How do I change the windshield washer resevoir


you have to go through the inner fender well on the side its on remove tire ,the screws and the pull it back and should see it,remove the upper portion by undoing the clips that hold it.good luck,mike

Jan 10, 2015 | 2004 Pontiac Grand Am

1 Answer

My windshield wiper fluid will not go thru to windshield,how can i fix the problem


Your line runs from the reservoir in the fender well, up through the hose around the strut plate on top, through the bezel to the wipers. If you have no leaks, Replace the washer motor. If you fill it and it leaks, fix the leaks. To access the reservoir. Remove the tire and inner fender well on the passenger side.

Oct 05, 2014 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

My 2005 Avensis sedan front windscreen washer does not work - wipers do still opperate. Where is the fuse for this located and what else could cause this problem?


PROBABLE CAUSE Impact to the front bumper pushes the bumper back far enough to break the washer pump hose fitting. CORRECTIVE ACTION Replace the windshield washer reservoir and washer motor with updated parts. REPAIR PROCEDURE 1. Turn the ignition switch to ACC (I) to unlock the steering column. 2. Raise the vehicle on a lift. 3. Remove the right front inner fender. Unhook and pull back the bumper for better access. CLIPS (6 places.) SCREWS (6 places.) RIGHT FRONT INNER FENDER 4. Release the hooks on the upper right side of the front bumper. 5. Remove the clip from the filler neck, then remove the filler neck. FILLER NECK CLIP WINDSHIELD WASHER RESERVOIR CLIP WASHER MOTOR CONNECTOR BOLT BOLTS WASHER TUBES 6. Remove the right front fender trim, and disconnect the washer hose from the 90-degree fitting. CLIP FRONT FENDER TRIM FRONT HOSE 7. Disconnect the 2P connector and the two washer tubes from the washer motor. 8. Remove the washer reservoir clip and the three bolts, then pull out the reservoir. 9. Assemble the new reservoir components, but do not install the filler neck. 10. Trim 85 mm off the end of the 1,260 mm washer tube only. 11. Route the washer tubes on the reservoir. NOTE: The black fitting is for the front windshield nozzles, and the white fitting is for the rear nozzle. 85 mm 12. Install the reservoir. 13. Connect the rear tube to the straight fitting in the wheelwell. 14. Connect the 2P connector to the washer motor. NEW RESERVOIR Connect the rear washer tube. CLIP BOLT 9.8 N•m (7.2 lb•ft) 15. Install the filler neck with the original clip. Connect the front washer tube to the 90-degree fitting. Then reinstall the front fender trim. WASHER FLUID DIPSTICK 2P CONNECTOR FRONT FENDER TRIM FILLER NECK CLIP

May 15, 2011 | Toyota Passenger Cars & Trucks

1 Answer

Windshield wiper fluid reservoir goes dry


After you pour the stuff in watch where it comes out. It is buried in the fender ...drivers side. Wheel well shield is removeable.

Oct 27, 2009 | 2006 Honda CR-V

1 Answer

Mercury villager 1994 washer pump not working


the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

Sep 09, 2009 | 1994 Mercury Villager

1 Answer

Removing the windshield washer reservoir in a 2002 Chrysler T&C


REMOVAL

  1. Disconnect and isolate the battery negative cable.
  2. Remove the engine fresh air housing inside the engine compartment.
  3. Disconnect the washer hose at the in-line connector forward of the cowl grille so that the in-line connector remains with the washer hose from the fresh air plenum.
  4. Disconnect the washer hose from the hose clip located on the front fender side shield.
  5. Remove the filler tube screw.
  6. Hoist and support vehicle on hoist or jack stands.
  7. Remove the right front wheel and tire assembly.
  8. Disconnect the left right front wheelhouse splash shield and move aside.
  9. Drain washer fluid from the reservoir and into a suitable clean container. This can be done by disconnecting the windshield washer hose from the front (outboard) washer pump and allowing the washer fluid to drain into a container through a temporary jumper hose connected to the front washer pump.
  10. Disconnect the electrical body harness connectors to the washer pump motors and the fluid level sensor. Slide the red lock on the connector to the release position, then, depress the black tab and pull the connector off the pump or sensor.
  11. Remove the two reservoir mounting screws.
  12. Disconnect the reservoir from the body mount by raising the reservoir upward slightly and then down so that the reservoir filler neck and front washer hose pull through the opening in the front fender side shield.
INSTALLATION

  1. Push filler neck and front washer hose through the opening in the front fender side shield. Connect the reservoir to the body mount by lowering the reservoir down.
  2. Install the two reservoir mounting screws. Torque screws to 8.5 - 11.3 Nm (75 - 100 in. lbs.) .
  3. Connect the electrical body harness connectors to the washer pump motors and the fluid level sensor. Slide the red lock on the connector to the closed or locked position.
  4. Assure that washer is properly routed to prevent pinching and possible inoperative washers.
  5. Connect the left right front wheelhouse splash shield and move aside.
  6. Install the right front wheel and tire assembly.
  7. lower vehicle from hoist or jack stands.
  8. Install the filler tube screw. Torque screw to 8.5 - 11.3 Nm (75 - 100 in. lbs.) .
  9. Connect the washer hose to the hose clip located on the front fender side shield.
  10. Connect the washer hose at the in-line connector forward of the cowl grille.
  11. Install the engine fresh air housing inside the engine compartment.
  12. Connect the battery negative cable.
  13. Verify system operation.

Apr 01, 2009 | 2002 Chrysler Town & Country

1 Answer

Wash wipe on a Focus 2000 model


I blieve it's the same pump taht runs the rear and front washers.

The windshield washer comprises the following parts:
  • Windshield washer reservoir, below the front left-hand fender
  • Washer pump, on the outside of the washer reservoir
  • Two washer nozzles on the hood/bonnet, adjustable.
---------------------------------------------------------
Windshield Washer Pump and Reservoir Removal
All vehicles
  1. Remove the windshield washer reservoir filler neck.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the right-hand fender splash shield (wheel shown removed for clarity).
  1. Remove the washer reservoir.
    • Disconnect the electrical connectors.
    • Pull off the hoses.
  1. Remove the windshield washer pump with rubber gasket (shown with reservoir installed).
    1. Disconnect the electrical connector.
    1. Disconnect the hoses.
    1. Lift out the pump.

Feb 27, 2009 | 2000 Ford Focus

1 Answer

Winshield washer motor does not run


These days, most windshield washer pumps are mounted to the bottom of the washer fluid reservoir. Where’s that, you ask? Well, inner+fender+w+text.jpgyou know that spout you pour the fluid into—the one that disappears into nowhere? Well, the reservoir is actually 2384f71.jpglocated inside the front fender between the bumper and the front wheel. To replace the pump, you will have to jack up the vehicle, remove the front wheel and then remove the inner fender liner.

Jun 08, 2008 | 2001 Honda Civic

Not finding what you are looking for?
2004 Jeep Liberty Logo

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...