Question about 2004 Mercury Sable

1 Answer

Need item name for brake sensors on and near the brake pedal

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 81 Answers

Brake pedal switch.

Posted on Oct 08, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Brake pedal falls just enough that the brake lights stay on, how do Ifix this

you can rig it by gluing or taping a coin (the most common item used) to the back of your pedal where it meet the brake light sensor, or you can replace the pedal. i hope this helps.

Jun 24, 2014 | 1993 Toyota Corolla

1 Answer

Parking brake will not keep car from moveing when i push e pedal to floor.

Without knowing which type of e-brake you have (foot pedal or handbrake), just about ever type of e-brake has two places to adjust it, well, that bears explanation. The one actual adjustment will be near the operator, either under the handle on a hand brake, or above the pedal on a pedal brake. You will notice that there is a long threaded rod with two nuts on it, loosen those and turn them down to pull slack out of the cable which runs to the rear wheels,

Now the other item is not so much an adjustment, it may be just wear on the pads or shoes of the brake itself. Some cars will use the regular braking pads/shoes as the same means for the e-brake, while others have pads/shoes committed to just the e-brake.

I would suggest attempting the cable adjustment in the drivers compartment first, as if this does not work you will be needing either a shop or brake mechanic to open the rear brakes.

Apr 05, 2014 | 1988 Oldsmobile Cutlass Ciera

1 Answer

On a 2005 chevy suburban my brake lights will come on after about 4 seconds but not right away. I would assume there is a sensor near the pedal. What do I look for and how do I check it?

the brake light switch is near the brake pedal it should have a wire (or wires) attached to it, it is activated when you push the brake pedal in, they are usually spring loaded & it could be sticking just give it a spray with WD 40 & see if that fixes it, if not it may have to be replaced.........hope this helps.......cheers.

Sep 16, 2011 | 2003 Chevrolet Suburban 2500

1 Answer

How do I replace my brake sensor? My brake lights will not turn off.

brake switch on pedal is probably missing the little rubber pad the plunger contacts when pedal is released. you probably have pieces of it on the floor under pedal. Dealer item a few dollars.easy fix

Aug 24, 2011 | Honda Accord Cars & Trucks

1 Answer

What is the sympton for bad break booster.i am confused--will the brake pedal be hard to push down or way to easy to push to floor. i have hissing sound in warm weather near brake pedal but not in cold...

Hello rickyjkoch: My name is Roger and I will help with your question. With the engine off, press the brake pedal down several times. Hold the pedal down and start the engine. The brake pedal should drop 1 1/2 to 2 1/2 inches toward the floor. If the pedal stays up and does not drop the booster has a problem. However if you hear a hissing sound from the dash area of the brake pedal the booster should be replaced. Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Jul 30, 2011 | 2005 Ford Escape

2 Answers

My 2000 Grand Voyager lost all the brake lights at the same time. The fuses are all good and so are the bulbs. I don't know what to do now any ideas???

It is most likely the brake sensor switch.Most are located on or near the brake pedal up high by the linkage.Good luck!Greg

Aug 28, 2010 | Plymouth Grand Voyager Cars & Trucks

2 Answers

Where is brake pedal sensor located on a vw golf

near the top of the arm that the brake pedal is attached to.

Mar 09, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

Sonata brake lights stay on, assume faulty switch, where is it to change?

The brake light switch should be on the brake pedal near the top. Look for a circular item or box with 2 or 4 wires coming out of it at the top end of the brake pedal.

Jan 07, 2010 | Hyundai Motor 1998 Sonata

1 Answer

Z3 brake light sensor

lay on your back in the drivers side and look up... it should be located just behind the brake pedal... move the brake pedal by hand and you should see the switch move

Mar 02, 2009 | 2001 BMW Z3

Not finding what you are looking for?
2004 Mercury Sable Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

80608 Answers


Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides