Question about 2004 Dodge Intrepid

1 Answer

Car was running well then just refused to start.Computer indicated throttle position sensor. Replaced that, then crank sensor, then cam position sensor. Then took car to a repair shop. They thought cam belt, all looked good. They then said wire to crank position sensor bad and replaced it. Car then started with miss fire. The repair shop then replaced all plug wires and plugs. car still miss fires, they then replaced the coil pack.Car still miss fires on passenger side cylinders. The car starts and runs on the driver side cylinders only. What gives with this?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Its possible there are multiple coil packs usually one for each bank or one for every two cylinders. Or check for a ignition control module

Posted on Oct 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trouble code PO335


fuse or fuel filter first! Cam sensor.

Nov 02, 2015 | Cars & Trucks

2 Answers

The car cranks but will not start. There is good fuel pressure but no spark. Thinking it could be the cam sensor or the throttle position sensor. Any other possible causes for the non start


Yes, check your plugs and wires... the throttle body and also check all of your vacuum hoses as well.

Pull one or more of your spark plugs and check to see if they are dry or damp with oil. This could be the result of bad rocker cover seal and or the seals around your spark plug chambers.

When attempting to start the car, if it turns over but no spark, then check plugs and wires, if you hear a clicking noise, then it could be a blown starter motor.

Oct 02, 2015 | 2002 Acura RSX

1 Answer

Why does my truck crank fine and run good except for a hard random miss every so often while driving down the road?


You'll probably need a shop to check it out.
The code for the cam sensor usually means the computer is not getting a signal, or it is not in sync with the crank. Since you replaced the sensor, the problem could be the cam or the circuit between the sensor and the engine computer.
There is a flow chart with tests to run for each trouble code.

May 02, 2015 | Cars & Trucks

1 Answer

Car cranks wont start


run fault codes to find the faulty sensor that is not allowing the injectors to work. It may be a cam position sensor . Check that the cam shaft is turning ( broken timing belt.)

Jan 20, 2014 | Cars & Trucks

1 Answer

I haved a 1989 Buick Park Avenue 3.8 engine...I have replaced the starter, coil pack, ignition module, crank sensor and cam sensor and still cannot get it to fire...I really NEED this car to run so PLEASE...


ok ! did you mean its got spark but does not start. if spark but does not start. check to see if its getting fuel to engine. remove air hose from throttle body and spray some starting fluid in throttle body, open throttle plate and spray some in. if car starts then stops, its a fuel problem. if no spark check the harmonic balancer on engine to see if its loose, the 3.8 engine have a crank position sensor that runs off the balancer. the rubber starts wearing out and the balancer start flopping around. and the timing gets massed up. good-day ! type in on pc browser ignition switch symtoms, and a list of things will come up. for a ignition switch controls over 50% of voltage for vehicle. good-day !

Oct 29, 2011 | 1989 Buick Park Avenue

2 Answers

1996 Ford Taurus SHO 3.4. Intermittant starting problem. Welded cams. First instance a couple of months ago. Had it towed to a local shop. Once there the car started right up. They kept it for the day...


try replacing the gas cap,may be vapor locked,check throttle position sensor by holding the pedal to the floor while cranking,if it starts then replace the sensor,if not it probably works

Aug 18, 2009 | Ford Taurus X Cars & Trucks

2 Answers

2004 Honda Civic -Code P0122 Throttle Position Sensor Voltage Low


yes, this is the case of a failed throttle body, in which case it needs replaced, the car is getting too much fuel causing the high idle. this needs replaced asap. you could proably find a small independant honda shop that could do the work for less.

May 12, 2009 | 2004 Honda Civic

1 Answer

Po300 code, replaced 1 crank sensor needing to know voltage on se


Resistance check the coils. Check for spark on all 6 cylinders.

Apr 02, 2009 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
2004 Dodge Intrepid Logo

363 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...