Question about 2000 Chrysler 300M

Open Question

Instructions on how to replace rear wheel bearing on a 2000 chrysler 300m

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

stormin25
  • 1 Answer

SOURCE: I need a free diagram of rear wheel bearing replacement

The question you asked me to clarify was really quite simple..... I needed a diagram of rear wheel bearing assembly for a 2000 Dodge Grand Caravan 3.38 litre, 6 cylinder, 2 wheel drive vehicle. You couldn't provide me with a diagram so I took the wheel off looked at the old one then the new one and just did it myself. Thanks for not helping.
Stormin Norman

Posted on Nov 13, 2008

  • 2 Answers

SOURCE: what torque for rear wheel bearing Ford Focus 2000

Can only find out that the hub needs to be tightened to
235 nm Dunno if this helps

Posted on Jan 27, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic

Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

Posted on May 23, 2009

  • 7 Answers

SOURCE: programming instructions for a 1999 Chrysler 300M remote fob

Manual Programming Procedure (non scan tool)
1. Connect pin 1 of the 16-way data link connector to chassis ground or to pin 4 of the 16-way data link connector.
2. Close all doors, turn ignition key to off.
3. Turn ignition key to Accessory.
4. Turn ignition to off, door locks will cycle once (in programming mode).
5. For each key FOB, press any button 3 times in a row to program code. When programming is complete, the door locks will cycle once.

NOTE:
IF A SECOND KEY FOB REQUIRES PROGRAMMING, IT MUST BE PROGRAMMED WITHIN 1 MINUTE OF PROGRAMMING
THE FIRST FOB PROGRAMMING. PRESS ANY BUTTON ON THE SECOND FOB 3 TIMES TO PROGRAM ITS CODE. WHEN PROGRAMMING IS COMPLETE, THE DOOR LOCKS WILL CYCLE ONCE.

6. The programming mode finishes after the following:
a. Programming of two key FOBS is completed.
b. One minute has passed since programming.
c. Pin 1 of 16-way data link connector is removed from ground connection.
d. Ignition switch is turned on.
e. Any of the doors are opened.

Posted on Jun 25, 2009

  • 119 Answers

SOURCE: Procedure for replacing rear wheel bearings 2000 Forester

i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Posted on Jul 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes a clicking sound on 2000 300 m chrysler front wheels?


The ball bearing balls in the CV joints can wear a groove when running in a straight line. When turning they cross the worn groove and make a clicking sound. Not a serious problem until you get abnormal tire wear.

Aug 28, 2014 | 2000 Chrysler 300M

1 Answer

2001 Chrysler 300m


Hi
The wheel bearing may carry the magnetic ring that the abs sensor uses to pick up a reading.
Replace bearing if its faulty and retest all as before.
Roger

Apr 24, 2017 | Chrysler Cars & Trucks

1 Answer

I'm driving a 2000 Chrysler 300M. Had front brake pads & rotors changed 2 weeks ago. Front end has been noisy since & I suspect sticking calipers , as i was informed they did not get clean


The front calipers are not the problem...did a shop replace the pads and rotors? Or did a friend replace these parts. The Chrysler front pads and rotors are an excellent design...easy to service and replace parts...only 2 bolts hold on each caliper, and the rotor is held in place with the caliper, and wheel. My first thought was a front wheel bearing is grinding, but you should have noticed this before the brake parts change. The pads could be installed backwards also...my second thought was you may have a loose wheel or two...retighten all 5 lug nuts by using the "star" tightening method, you may be surprised that the loose lug nuts are the only problem. Hope this helps.

Jul 12, 2012 | 2000 Chrysler 300M

1 Answer

I have a 2003 Chrysler 300m. When its cold in the morning it sounds like I have a flat tire front left. Tire pressure is ok and sound is more pronounced when turning. Sound goes away after it warms up. Is...


Check the tire on the front of the car for a broken belt in tire. Look on the back side for a blug,swollen area on side wall of tire. Raise the front of car and block the rear wheels, spin the tire by hand and look on both sides as tire is rotating for anything unusal. Hope this will help you.

May 18, 2010 | Cars & Trucks

1 Answer

Need cylinder numbering order for a 200 chrysler 300m, front wheel drive. The engine is not tranverse mounted. Thanks, Rick B


For the 2000 Chrysler 300M 3.5L:

Firing Order:
1-2-3-4-5-6

Cylinders:
...(back)
.............6
5
.............4
3
.............2
1
...(front)

Ignition Coils on respective Plug

Mar 19, 2010 | 2000 Chrysler 300M

2 Answers

Where is the battery on a 2000 300M?


did you look under the rear seat?

Jan 04, 2010 | 1999 Chrysler 300M

1 Answer

How to replace a rear wheel bearing on voyager


this is a one piece part hub and bearing assy. even if auto parts sales you bearing separated highly recommend to replace whole unit

Nov 19, 2009 | 2000 Chrysler Grand Voyager

1 Answer

Does a 1999 chrysler 300M use shock absorbers or struts?


if front wheel drive its struts
if rear wheel drive its shocks
this is how you tell them apart

Dec 06, 2008 | 2000 Chrysler 300M

Not finding what you are looking for?
2000 Chrysler 300M Logo

Related Topics:

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...