Question about 1995 Ford Econoline

1 Answer

Replaced rear speed sensor cleaned front abs sensors abs lights on over drive light blinks no cruse control

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 75,066 Answers

Did u replace the Vehicle Speed sensor on the transmission? that is what would cause the cruise to be inop and blind the OD light. it is on the rear tailshaft of the transmission, see photo below of VSS, aldso make sure the connector at the sensor is not full of oil or otherwise making a poor connection.replaced rear speed sensor - 3c5d062.jpg

Posted on Oct 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the probable causes of DTCs C0222, C0226, and C0237?


Brent, Check and clean connections(use electronic contact cleaner), make sure wires are not damaged. Check grounds from EBCM controller. Check links below and don't be afraid to google search for more info.
C 0222 Missing Right Front Speed Signal
C 0226 Missing Left Front Speed Signal
- Faulty Right/Left Front Speed Sensor
- Right/ Left Front Speed Sensor harness is open or shorted
- Right/ Left Front Speed Sensor circuit poor electrical connection
- Faulty EBCM

C 0237 Erratic rear speed signal
- Faulty Rear Speed Sensor
- Rear Speed Sensor harness is open or shorted
- Rear Speed Sensor circuit poor electrical connection
- Faulty EBCM


How fixed Chevy with an Abs and Brake light on

https://www.google.ca/url?sa=t&rct=j&q=&esrc=s&source=web&cd=3&cad=rja&uact=8&ved=0ahUKEwi0i8zz5YzLAhWD74MKHffwDLQQtwIIITAC&url=https%3A%2F%2Fwww.youtube.com%2Fwatch%3Fv%3DR_5WZUebDx8&usg=AFQjCNHimqe_Fje8AySjD5N0Wh8z8dQuuw

How To Install Replace Front ABS Sensor and Harness 2000 06 Chevy Suburban...

Feb 23, 2016 | 2003 Chevrolet Tahoe

1 Answer

2010 Toyota taca access abs light on Cruse light blinks traction light on.how to fix


Hi William the ABS and cruise contro are both linked it could be a wheel speed sensor or a damaged active bearing. The best way to be sure is to get it plugged in to diagnose correctly. Regards Jim...

May 17, 2015 | 2010 Toyota Tacoma

1 Answer

Need help locating vss on trans for a 2000 F350 4X4 7.3 motor


1. Your ABS/ VSS can be removed and cleaned with just a clean rag, no need for wd-40 or any other solvent, also carefully clean out the hole on top of the differential, lift the vehicle (place in neutral) and check the sprocket wheel inside the pumpkin for possible missing teeth or to see if it is loose.

2. The VSS (part # F85F-9E731-AA) can also be tested with an ohms meter, it should measure ~1.9 K-ohm or higher (lower than 1.9 requires replacement).

3. The VSS is a hall-effect sensor, connect a volt meter to the sensor connector and wave a piece of metal (pair of pliers or flat metal) about a half inch away from the sensor, and you will consistently see a variation in voltage, if no movement on the volt meter is observed, replace the sensor.

4. You also have the two front wheel ABS sensors, try cleaning them first, and carefully reinstalling them.

5. When the VSS sensor is malfunctioning, the PCM may try to get input from the TSS (turbine speed sensor, top of the transmission), and as it turns out, the same return wire is used by the OSS (output speed sensor, tail end of transmission), check these two sensors also, clean them and test them (1.10 K-ohm or higher). These are also Hall Effect sensors, so check for voltage as described in paragraph 3 above.

6. Pay attention to see if your ABS light blinks when you start the vehicle, just before it stays solid. If this is happening, count the number of blinks, as this is actually a code and the blinking means the vehicle is trying to communicate with you.

7. Last, if nothing above corrected the problem, I would start tracing RFI (radio frequency interference), one sure area is usually your fuel pump (wires running along side VSS wiring. ABS/VSS wiring is routed directly to the ABS module.

I hope this information works for you.


There are two "speed sensors" though that can be confused at the parts store. They don't look the same but they are listed almost the same. The one on the rear diff is listed as the "ABS speed sensor"....the one on the tranny is listed as the "Speed sensor" The rear one is the cheapest and easiest to replace...about $12.

Feb 24, 2013 | Ford F-350 Cars & Trucks

2 Answers

Abs light stays on and odometer quit working


Hi!!
When Yellow ABS warning light illuminates during normal operation, the system has detected a problem and has stored a Diagnostic Trouble Code (DTC). Loss of power to module will cause system to be deactivated and Yellow ABS warning light to be illuminated. This fault will not set a DTC.
The Rear Anti-Lock Brake System II (RABS II) Speed Sensor is located on the Rear Differential Case. This sensor sends the speed signal of the rear tires to the RABSII Control Module, which also receives the Turbine Shaft Speed Sensor. The RABSII Control Module uses both signals to control the RABS II Proportioning Valve. If the RABSII Control Module does not receive both signals, the ABS Light will come ON.
Finally, the Sensor I think is giving you trouble. The Turbine Shaft Speed (TSS) Sensor is located on the transmission tail. This sensor sends the speed signal to the PCM which in turn sends it to the Speedometer and to the RABSII Module. If this sensor is disconnected or inoperative, the Speedometer won't work and the ABS light will come ON. Check electrical connector to the sensor, make sure is clean, free of corrosion and properly connected.
Before you replace the sensor, have the computer codes scanned for FREE at AutoZone, Checkers or similar autoparts store.
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Jan 06, 2011 | 2000 Mazda B-Series

1 Answer

1999 durango the abs light and brake light comes on about 3 or 4 times in the past week as im driveing and then goes off in a few minutes i have new brakes and roters on the front and only rear wheel abs,...


did you check the speed sensor on the rear end on top of the rear end. this sensor works the speedometer the abs and break lights and power door locks

Aug 30, 2010 | 1999 Dodge Durango

1 Answer

Speedo suddenly not working and two warning lights appeared on dashboard one being ABS light warning light.


If the ABS (and likely the traction control) light came on at the same time that the speedometer stopped working, you likely have a faulty wheel speed sensor at the right rear wheel. You can test this by swapping the two rear wheel speed sensors (ABS sensors). If the speedometer then works (but the ABS & Traction control lights stay on), replace the sensor that is now at the left rear (was at the right rear). If no change, you may have a fault in the ABS & Traction control - control unit.

Rear wheel speed sensor at www.bavauto.com

http://www.bavauto.com/shop.asp?HC1=0&Htarget=search.asp&HCY=2001&HCM=330i&SearchStr=rear%20abs%20sensor

Nov 22, 2009 | 2001 BMW 330

1 Answer

Overdrive contoll button is blinking on 200 f-350 7.2 powerstroke


It sound is if your ABS/Speed sensor is the culpret.  Try this fairly inexpensive repair before you bring it in for a Diagnostic, which can run anywhere from $89.95 & up.  Go to the local ford dealer in your area and ask them for the ABS Sensor in your rear axle differential. The base part number being 9E731. This part runs roughly for about $20.00+ and your own time to replace it. 

Mar 23, 2009 | 2000 Ford F350 Super Duty Super Cab

2 Answers

E280 1994: ABS lights comes on, Engine stall during driving


Clean your ABS sensors thatg is mounted on the front disc rotors - they are usually covered with metal fillings and dust due to the magnetic properties of the sensors and also check or replace overload relay located behind battery - "Oldmerc" Australia

Oct 28, 2008 | 1990 Mercedes-Benz E-Class

Not finding what you are looking for?
1995 Ford Econoline Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...