Question about 2001 Ford F250 Super Duty Super Cab

1 Answer

Replacing the water pump and dont know how to remove the fan f250 diesel

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 57 Answers

These are reverse thread. you have to loosen by stricking the fan wrench clockwise.

Posted on Oct 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does a 97 f250 7.3 diesel have a fuel shutoff switch and if u have duel tanks does it have 2 pumps


You should have a cutoff swich under dash on pass side of truck.
The fuel pump a a 7.3 1997 f250 is behind the fuel/water separator.Between the cyl heads.Remove the turbocharger then fuel/water sep.remove banjo bolt and seal ringsat rear of pump.remove line asmby
one for each cyl head at rear.and remove fuel asmby.
Ensure camshaft lobe for pump is on base circle with lobe facing away
from pump to prevent pump damg.

Jan 17, 2012 | 1997 Ford F250 SuperCab

1 Answer

My1990 ford f-250 leaks coolant below fan when i put it in.how do i fix it?


Hi:) Sounds like the water pump needs to be replaced. you need to remove the coolant,belt,fan,water pump bolts and you need a new gasket and water pump and replace in opposite order.

Mar 17, 2011 | 1990 Ford F250

2 Answers

How do I remove the fan clutch to replace the water pump on a 1985 F250 6cyl 300 cu in?


There are bolts on the back side of the water pump pulley remove them take rubber hammer tap clutch off water pump

Jan 04, 2011 | 1985 Ford F 250

2 Answers

Need to replaCE WATER PUMP 2002 GMC DURAMAX DIESEL how hard?


cardenderek,
This info is totally bogus.You obviousely have never changed a water pump on a 6.6 liter Duramax Diesel engine.1st off it isnt belt driven it is gear driven from the drive train inside the engine.You have to remove the fan shroud,clutch fan assem.,and harmonic balancer as one of the mounting bolts is behind the balancer.Also remove the left side inner fender for easier access.

catD8RII

Mar 12, 2010 | 2002 Chevrolet Silverado 2500HD

1 Answer

My 1991 ford f250 deisel runs warm and pushes


Three possibilities are clogged oil cooler (most likely as you only said while towing) bad fan clutch (easiest to try first) or bad head gaskets.

Oct 24, 2009 | 1991 Ford F250

1 Answer

Water pump


Please RATE ME
This IS EXACT Procedure Bu The BOOK
REMOVAL
  1. Drain cooling system.
  2. Loosen fan clutch attaching bolts.
  3. Remove fan shroud attaching bolts and remove shroud and fan.
  4. Remove drive belt.
  5. Disconnect lower radiator hose, heater hose and bypass hose from water pump.
  6. Remove fan, spacer, water pump pulley and fan shroud.
  7. Remove A/C compressor/power steering pump bracket and accessories to clear water pump stud bolt.
  8. Remove water pump attaching bolts and the water pump.
INSTALLATION
  1. Reverse procedure to install. Tighten water pump retaining bolts to 12-18 ft. lbs.
NOTE: All water pumps have a sealed bearing integral with the water pump shaft. The bearing requires no lubrication. A bleed hole in the pump housing allows water that may leak past the seal to be thrown out by the slinger. This is not a lubrication hole. If the pump is damaged and requires repair, replace it with a new pump or a rebuilt one.
I Need your Help Also !! PLEASE RATE ME

Jan 27, 2009 | 1995 Ford F250

1 Answer

Replacement of all 4 belts.


Get a old leather belt cut it in half . Now put a hole in each cut end and drill it to the back of the cab.

Oct 19, 2008 | 1991 Ford F250

1 Answer

What tools do you need to replace a 1997 Ford F250 diesel fuel pump?


nothing special, its in the valley, probably have to remove the fuel bowl and the turbo pedastal to get access to it.
book value from navistar / ford is a 4 hour job.
better have a good ladder and a plywood sheet to lay on up in the engine bay.

Jul 05, 2008 | 1997 Ford F250 SuperCab

Not finding what you are looking for?
2001 Ford F250 Super Duty Super Cab Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...