Question about Jeep Cherokee

1 Answer

Step by steps needed to install a starter on a 2000 jeep cherokee 6 cylinder

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Fairly simple job.
Disconnect the battery, then remove the two bolts that hold the starter to the bellhousing.
Lower the starter and unbolt the wires on the solenoid.
To install reverse procedure. be careful not to over-tighten the wire connections. the cover is plastic and can break. Also when tightening the bolts that hold the starter in, Run one in most of the way, then the other, make sure you keep the starter square with the mount and alternate tightening one bolt (best at top) then the other 'till they are snug, then after it is fully in, just tighten them up fully.
Before you start the job, If you have an alarm, make sure you know how to re-arm it (same as dead battery procedure) same for radio.

Posted on Oct 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace spark plugs on 2000 jeep cherokee classic 6 cyl.? Also does 2000 cherokee have inline fuel filter?


TO REPLACE SPARK PLUGS YOU REMOVE COIL PACK MOUNTING BOLTS THEN REMOVE THE COIL PACK WITH BOOT OVER THE SPARK PLUG.YOU HAVE 6 INDIVIDUAL COIL PACK TO EACH CYLINDER. YOU NEED A 3/8 RATCHET WRENCH - LONG 3/8 EXTENSION -SPARK PLUG SOCKET - SPARK PLUG GAUGE.AND TORQUE WRENCH.THE 2000 MODEL JEEPS FUEL FILTER INSIDE THE TANK.1993 - 1996 MODEL JEEPS FUEL FILTER LOCATED LEFT SIDE OF THE VECHICLE NEAR THE FUEL TANK.

Jul 20, 2010 | 2000 Jeep Grand Cherokee

2 Answers

What is the torque specs for a 1998 jeep Cherokee classic straight 6 4.0 liter? I am replacing the head gasket and need to find the lbs of torque. Thank you for any advice, pictures, etc.


Torque sequence ------------------ front | 12 8 4 1 5 9 13 | of | | engine | 11 7 3 2 6 10 14 | ------------------ Final torque must be reached in 3 equal steps Step 1: torque all bolts (except bolt 11) to 110 Ft/Lbs Step 2: torque bolt 11 to 100 Ft/Lbs Recheck final torque in sequence.

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Disconnect the hoses at the thermostat housing.
  4. Properly relieve the fuel system pressure.
  5. Remove the cylinder head cover.
  6. Loosen the rocker arms.
  7. Remove the pushrods.

The valvetrain components must be replaced in their original positions.
  1. Remove the intake and exhaust manifold from the cylinder head.
  2. Disconnect the spark plug wires and remove the spark plugs.
  3. Disconnect the temperature sending unit wire, ignition coil and bracket assembly from the engine.
  4. Remove the accessory drive belt(s).
  5. Unbolt and set aside the power steering pump and bracket. Do not disconnect the hoses.
  6. Remove the intake and exhaust manifold assembly.
  7. If equipped with A/C, perform the following:
    1. Remove the compressor and position it aside with the lines attached.
    2. Remove the compressor bracket bolts from the cylinder head.
    3. Loosen the through bolt at the bottom of the bracket.

  8. Remove the alternator.
  9. Remove the cylinder head bolts, the cylinder head and gasket from the block.

Bolt No. 14 cannot be removed until the head is moved forward. Pull the bolt out as far as it will go and suspend in place by wrapping with tape.
  1. Discard the gasket. Thoroughly clean the head-to-block mating surface.
  2. Clean and inspect the cylinder head thoroughly. Refer to the engine reconditioning portion outlined later in this section.

To install:
  1. Coat a new head gasket with suitable sealing compound and place it on the block. Most replacement gaskets will have the word TOP stamped on them.

Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Oct 08, 2009 | 1998 Jeep Cherokee

1 Answer

What is the firing order of a 2005 jeep grand cherokee


I wrote all engine spec for a 2005 jeep grand cherokee

3.7L 6 cylinder
1-6-5-4-3-2

4.7L 8 Cylinder
1-8-4-3-6-5-7-2

5.7L 8 Cylinder
1-8-4-3-6-5-7-2

let me know if this help you.....

Sep 30, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Replace a washer pump for 2000 jeep cherokee 6 cyl.


Visit the autozone.com website and register the vehicle. It doesn't cost anything and you will have access to an online repair manual for the vehicle. The steps for replacing the water pump should be available there. Hope this helped and best wishes.

Sep 07, 2009 | 2000 Jeep Cherokee

2 Answers

What is the tension on cylinder head bolts for a jeep grand cherokee 307935 4 litre, 6 cylinder, 1999, petrol motor.


Coat threads of left hand front bolt with sealant: 1st - step; - 22 ft./lbs. 2nd - step; - 45 ft./lbs. 3rd - step, all bolts except L.H. front bolt; - 110 ft./lbs. 4th - step, L.H. front bolt; - 100 ft./lbs. fig100.png

Sep 05, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Crankcase sensor


Crank sensor? Not necessary for long instructions ...It's located in a hard to reach place, on the trans bellhousing, even with the flywheel on the drivers side about 10 oclock looking from the rear to front. The harness extends to near the master cylinder up at the firewall. It's held on with two small screws. Easier to say than do, but remove the screws, take it out, put the new one back in.

May 13, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Jepp Cherokee 2000 4.0 L 123K miles, cylinder #6


try changing your crank senor. Get part from the dealer... My jeep was misfiring and changed OEM part and jeep rides good.

Apr 27, 2009 | 2000 Jeep Cherokee

2 Answers

2000 Jeep Grand Cherokee Electrical Problems


Sounds like the ECM....the computer that controls all the electrical functions on the car is having some major issues or needs to be replaced. A auto repair or auto parts store should have a diagnostic machine that will tell you for sure or you can purchase one for between $50 and $150

Apr 13, 2009 | 2000 Jeep Grand Cherokee

2 Answers

Replacing water pump on 2000 Jeep Grand Cherokee V6


i have a 2000 grand laredo jeep cherokee that is leaking fliud bad i think it the water pump how do i fix it ??

Jan 10, 2009 | 2000 Jeep Grand Cherokee

1 Answer

I need repair instructions for changing the head gasket on 2000 Jeep Cherokee Sport


your best bet would be to go to a local parts store and purchase a Haynes manual for your specific vehicle, this will give you step by step instructions as well as all the required torque specs. The Haynes manuals are around $ 25.00 canadian. hope this helps you.

Oct 08, 2008 | 2000 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...