Question about 2004 Nissan Altima

1 Answer

I changed my brake on an nissan altima 2004 and bleed the brakes now I have no pressure on my petal.......... can you help?

Posted by on

Ad

1 Answer

Bleed them correctly
You had no issues before you opened the system,correct.

Posted on Oct 09, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Navara d22 brake pedal slowly goes to the floor only when engine is running I have changed master cylinder ,rear shoes,rear cylinders as they were leaking bled oil can you help


nissan vehicle have a problem in the bleeding of the brake and as a result pressure bleed is more effective that the normal method
Take the vehicle to an accredited brake shop and have the brakes pressure bled or have a proper diagnosis done to find the fault

Dec 14, 2016 | Nissan Navara Cars & Trucks

1 Answer

My 2008 Nissan Altima 40,000miles needs new brakes in the front, according to the dealership. Does this mean I need new brake pads? The dealership also said the brake system fluid was dirty and cont


Yes, it's typical for any vehicle to have the front brake pads and rotors replaced at 40,000 miles or less. A complete service would involve (2) new front brake rotors, (1 set) of new front brake pads (this includes 4 pads), brake fluid, silicone brake grease for the slide pins and possibly new slide pins (If they're corroded) and rubber seals for the slide pins. Because of the age of your vehicle, it's always a good idea to have the brake fluid changed (This means that your mechanic should bleed the brake system by opening the bleed screw on all (4) brake calipers). Brake fluid absorbs moisture over time and will start to break down (Lower the boiling point) and cause rust inside the system making your brakes less effective. Look at the brake fluid reservoir under the hood. The fluid should appear either clear (Perfectly clean) or slightly yellowish. If it appears to be light to dark brown, it's time to change it. If I were you, I would shop around for prices at other reputable service shops. Your dealer is going to charge you top dollar for this service. Hope this helps.

Aug 08, 2014 | 2008 Nissan Altima

1 Answer

While driving on the interstate my 2008 sentra auromatic drops put of overdrive and the cruise control turns off


check your brake petal height may need to bleed your brakes to bring the petal back up so the switch don't get bumped by the brake petal

May 07, 2014 | Nissan Sentra Cars & Trucks

2 Answers

How to bleed brakes


Supplies you will need:

bottle of brake fluid

small clear container

18" length of 1/4 inch I.D. clear tubing

wrench that fits your bleed screw

another person

Open hood,loosen lid to brake reservoir to be able to monitor fluid level. Removing the tires makes it easier to access bleed screws but not necessary on all vehicles. Start at the caliper farthest from the reservoir, attach tubing onto bleed screw so it is tight fitted on bleed nipple.Put enough brake fluid into clear container and put open end of tubing into fluid, ensure tube stays in fluid throughout entire process as to not suck air into system. Have your assistant sit in car and pump brake pedal three times and hold to floor, then loosen bleed screw just enough to relieve pressure in brake line, the brake pedal will sink right to the floor..this is normal. DO NOT RELEASE BRAKE PEDAL UNTIL BLEED SCREW IS TIGHTENED AGAIN. Repeat this process until clear tube is full of brake fluid and no bubbles come out of caliper. Repeat steps for all calipers. Hope this helps

Apr 05, 2014 | 1995 Nissan Altima

1 Answer

Need help bleeding brakes 2004 ford explorer


To bleed the brakes 1st make sure the fuild level is full ,and you will need a assistant . have your assistant pump the brake petal three to four times then hold presure on petal (pushing down ) then open the bleeder valve on the left rear caliper ,have assistant push petal towards the floor until it stops and then hold it there until you close the bleeder valve ,then repeat process four to five time recheck brake fulid level then repeat same process on right rear caliper next go to right front and end on left front ,keep a eye on the fuild level so that it is not allowed to run out or you will have to start over again ,there is no speical procedure ,any other questions just ask

Dec 29, 2010 | 2004 Ford Explorer

1 Answer

I have a 2008 Nissan Altima with push button start that will not start when the ignition button is pushed and the brake are being pushed on. The brake indictator light on the instrument panel goes on. I...


When you push the brake pedal do the rear brake lights come on?
Check that next time it does not start.
You may need a simple brake light switch adjustment.

May 03, 2017 | 2008 Nissan Altima

1 Answer

Just changed the rear brakes on my altima, pulled the star nut in as much as possible, still can't get hub back on..Help!


Bleed the brake fluid a little, until the brake liners retract a tad more. After installing the wheels, hard braking in reverse will adjust the rear brakes just fine.

Sep 07, 2010 | 2001 Nissan Altima

2 Answers

After changing pads and roto's on the front the brake petal goes to the floor and won't recover pressure? I didn't loosen brake lines or bleeders


You obviously got air in your lines while you were changing the pads. The brakes now need bleeding. Once you bleed them, your pedal will come firm again. But the good news is that you will only have to bleed the front brakes....Please don't forget to rate this answer for me...

Feb 22, 2010 | 2002 Ford SVT Focus

1 Answer

Bleed the brake lines


start at the passenger rear tire, have someone PUMP up brakes and hold pressure on them, release pressure by locating small bleeder screw, loosen screw 1/4 turn, brake fluid/air should come out, after brake petal reaches floor tighten bleeder, repeat process until only brake fluid comes out. go to driver side rear repeat, go to pass. side front repeat, go to driver side front repeat, after each bleeding make sure you check brake fluid in reservoir.

Sep 24, 2009 | 1984 Ford Mustang

Not finding what you are looking for?
2004 Nissan Altima Logo

Related Topics:

220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...