Question about 2005 Chevrolet Uplander

Open Question

Adjust headlights on a 2005 chevy uplander - 2005 Chevrolet Uplander

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
lebones337
  • 152 Answers

SOURCE: 2005 chevy express van where is Headlight adjustments

here is a link to a repair guide for your vehice that will help you with the headlights along with any other thing you might need.
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800b4a31

Posted on Feb 12, 2009

Ad

SOURCE: how to adjust headlight of Honda 2005

open the hood by the lights u will see a hole wth a light symbl near it put a long screwdriver in and turn the click wheel thing that will raise/lower the whole headlight assembly. ADJUST THE LOW BEAMS BECAUSE THE WHOLE ASSEMBLY MOVES HIGHBEAMS ARE NOT AS IMPORTANT

Posted on Aug 07, 2008

  • 1986 Answers

SOURCE: How do you adjust the headlights in a 2005 Chevy

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 04, 2009

duane_wong
  • 6826 Answers

SOURCE: how to change headlight fo 2005 chevrolet uplander

Headlamp Removal & Installation Bulb Replacement To Remove:

  1. Remove the Headlamp Assembly. Headlamp bulbs gm-06-00-3206.gif

  2. Turn the high/low beam bulb socket counterclockwise to remove.
To Install:
  1. Turn the high/low beam bulb socket clockwise to install.
  2. Install the Headlamp Assembly.
Headlamp Assembly (Park, Turn, Cornering and Side Marker Lamps) To Remove:
Headlamp assembly R &I gm-06-00-3207.gif

  1. Rotate the headlamp assembly retainer pins and pull up to remove.
  2. Remove the mounting bolts.
  3. Disconnect the harness connectors.
To Install:
  1. Connect the harness connectors.
  2. Position the headlamp assembly on the panel.
  3. Rotate the retainer pins and push down to lock in place.
  4. Install and secure the mounting bolts.
prev.gif next.gif

Posted on Oct 07, 2010

  • 63 Answers

SOURCE: how to change the headlight

There is no easy way to reach the bulb with the light assembly installed. It must be removed to gain access to the lights. I have below a proceedure that I have put together for this vehicle that covers the front and rear lights. at the end, I have a list of the bulb numbers. I hope this will help you>>>>>

Chevy Uplander (2005) Headlight bulb or turn signal replacement:


It is important to ensure all lights are working for the safety of you and others on the road.


Headlight:

In order to gain access to the head light bulbs, the headlight assembly must be removed. There no easy way to gain access to the lamps with the assembly installed. Open hood. Use 10mm wrench to remove faster on top of the light assembly closest to the rubber hood rest. You then need to remove the silver looking pin near the grill. This pin is snapped in place. Rotate counter clockwise and then pull pin straight out. The light assembly will now have to be pulled past the front header panel near the grill. Use care as the light is pulled past the grill panel. When you have this done there is one more fastener holding the light to the vehicle. On the far out side edge of the light near the fender panel, there is a ball socket fastener holding the light to the vehicle internal frame. Pull straight forward to pull the ball pin out of the socket. It will take a lot of force, but be careful as you apply force and pull light out forward. My light took some wiggling up and down, left and right until the ball released. Once the light is out, the lights are accessible. Both the normal and high beam light sockets rotate counter clockwise to remove from the headlight housing. There is a very tight detent in the counter clock rotation which took a fare amount of force. Once it "clicks" past that point during rotation, the light socket was able to be pulled from the light housing. The light bulb pulls straight out of the socket. Please use a clean towel or gloves to protect your fingers. Bulbs can sometimes crack and cut your fingers. Also, when you install the new lamps, use a towel or cloves as not to get oil on the glass which can cause uneven heating of the glass and crack it under use.


With the light assembly out, it is now easy to reach down into the vehicle to change the turn signal. This lamp is colored since the turn signal lens is clear.


Once bulbs are replaced, please test them before reassembly just in case of any issues. The headlight assembly ball socket will snap back into place easy. Once that is in, press the rest of the light back to its normal place. When the holes are lined up, please the silver colored rod back into its slots all the way down the inside of the light assembly. It then can be rotated and locked back into place. Reinstall the 10mm bolt on top of the light assembly near the rubber hood rest. Again check the lights to insure nothing is out of order.


Rear Lights:

To gain access to the bulbs to the real light assemblies, you must remove the light housings. Open up the rear hatch. Use a T30 Torex screwdriver and remove the two screws on the inside of light. Once those are out, the light assembly can be pulled out slightly from the vehicle. On the side of the van, the light assembly is held in place by two snap fasteners. Pull the light towards the rear of the vehicle to disengage the outside edge fasteners. Once done, the light assembly will be loose and the bulb sockets are accessible. They rotate counter clockwise release from the housing. The bulbs themselves pull straight out of the socket. Please use a towel to protect your hands and to make sure no oil gets on the bulb surface. Once done, reinstall the light assembly by first lining up the two plastic fasteners on the outside edge to the vehicle panel and press the light assembly to the vehicle. Reinstall the two screws and test light. Be sure to have someone press the brake for you to ensure your brake light works.



Bulbs:

Front:


Low beam/ high beam lights: (12362LL) Phillips (H11LL)

Front Turn Signal: 4157NAK amber color

Corner marker lamp: 194FH4 clear


Rear:

Brake/turn light: 4157LL (clear lamp)

Lower back up light and top running light: 3057XX (Wagner) (clear lamp)



.

Posted on Jan 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need serpentine belt diagram for a 05 Chevy


Go online and search "Chevy Uplander 2005 drive belts" and on "images" there are all sorts of pictures. On the main web are several sites with "How to's"

Oct 20, 2014 | 2005 Chevrolet Uplander

1 Answer

Wiring pulsar meter 2010 in 2005 chevy uplander


what color is the speed secor wire and where is it located

Sep 01, 2012 | Cars & Trucks

1 Answer

How many lbs. pressure a/c go'es into 2005 chevy uplander van


Empty with front and rear air - probably 2.5 lbs which is more than 3 cans.
There should be a sticker under the hood that says. Maybe in your owners manual too.

Jun 28, 2012 | 2005 Chevrolet Uplander

1 Answer

How do i change my left turn light bulb in my 2005 chevrolet uplander


Take out 1bolt just above headlight that holds headlight in place.Then to the left of headlight there is a 6inch pin you have to turn clockwise 1/4 turn then pull up and out.Remove headlight,ther is enough wire to put it to the side while you change the left turn signal.When the headlight is out of the way you can see the wires for the turn signal,turn the plug counter clockwise and pull,you will see lightbulb,pull out and change.To install do the reverse in order.

Aug 04, 2011 | 2005 Chevrolet Uplander

1 Answer

2005 chevy uplander how to program key FOB?


Get a trick-Charger and hook up to battery, turn new key in ignition switch to "on" but do not start engine, turn headlights on ( thats why you need the charger) and leave it like that for 100+ minutes.
That should do the trick and reprogram the new key, otherwise dealer only! about $130.00

Dec 13, 2010 | 2005 Chevrolet Uplander

1 Answer

How do you adjust headlight on 2008 uplander


If you look at the top of the head light assembly with the hood open just past the top rubber seal, you will see an alan head adjustor screw. This will adjust the low beam light up and down. the high beams are fixed. I would suggest shining your headlights on to a wall or garage door to get them to the same hight you need.

I am assuming that the design was not changed from my 2005 updander to your 2008. I had to adjust mine while on a road trip. We had a lot of people and stuff in my vehicle which made the headlights shine higher than normal. I was getting a lot of on commig traffic flashing. I was able to ajust them down fairly easy with those adjustor screws. Hope this helps.

Nov 30, 2010 | 2005 Chevrolet Uplander

2 Answers

Need to remove factory overhead rear DVD player in a 2005 chevy uplander


how do I remove my dvd player in my 2006 chevy uplander? I need to replace it and dont want to spend that kind of money to have it pulled out. I dont see any screws or bolts

Nov 20, 2010 | 2006 Chevrolet Uplander

1 Answer

Need picturss on how to change headlights for 2005


if you have a owners manual its in there, if not there is a pin and a screw on top on headlight assm. you take out and assm. pulls out to access headlight and turn signal bulbs.

Oct 13, 2009 | 2005 Chevrolet Uplander

1 Answer

2005 chevy express van where is Headlight adjustments


here is a link to a repair guide for your vehice that will help you with the headlights along with any other thing you might need.
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800b4a31

Feb 12, 2009 | 2005 Chevrolet Express

Not finding what you are looking for?
2005 Chevrolet Uplander Logo

Related Topics:

572 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...