Question about 1993 Chevrolet S-10 Blazer

1 Answer

How do you get the starter out after you take out the bolts? Seems there is not enough room for it to come out

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

Your gonna have to take the bell house off,you will also have to take down the drive shaft at the front end,to get the bell house off.the bolt on the right side,is blocked by the drive shaft,,,,,i just changed mine a week ago

Posted on Nov 27, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change my starter on the 2004 sienna


just take out the battery and you should have enough place.Its only three bolts for the starter,make shure you mark and take off the wires first.Or try from the bottom of the car.Take of the protection plate on the bottom

Mar 16, 2014 | Toyota Sienna Cars & Trucks

1 Answer

Removing harmonic balancer


First, you have to loosen the crank pulley center bolt. Best way is with an impact gun-bolt is very tight. If you have to use a breaker bar to loosen the bolt, you will have to devise a way to hold the crankshaft from turning backward while loosening it. One method is to remove the starter and wedge a piece of wood against the flywheel, preventing it from turning, while you are loosening the center bolt.
From the beginning: raise and block the side of car that the front of engine is towards. Remove the wheel and the inner fender splash shield. Remove the belts. Remove negative battery terminal, remove starter. Wedge the flywheel so it won't turn backward. Loosen and remove the center bolt. Some harmonic balancers will slide right off the crankshaft now, some are on very tight, if you can't wiggle it, tap it, and get it to move, then buy an inexpensive harmonic balancer removal puller, just a few bucks, easy to use, will save balancer from trying to hammer it off. All you need is enough room to mount up the puller to the balancer, and get the balancer moving off the crank.
Some engine lay outs there isn't enough room: then you really have to get creative, either lowering engine enough to get to pulley, or raising engine out. But most engines are positioned where the crank pulley can come off easily, with enough room to get the puller on.
The pulley may have a woodruff key in a slot on the crankshaft, and a corresponding notch on the pulley, for proper positioning of the pulley to crank. Don't lose the woodruff key.

Sep 01, 2013 | Pontiac Trans Sport Cars & Trucks

1 Answer

Removing a starter from a 1991 chevy s-10 blazer 4x4 , 4.3L v6...


The starter is under the vehicle on the passenger side. The best way is to turn your wheels to the left so you can reach the top of the starter solenoid behind the passenger tire. First undo the nuts from the solenoid terminals, second loosen the bolts holding the bell housing for the flywheel and slide it over enough to make room, third undo the starter mounting bolts and the starter should come out easier. And just reverse the steps for installation.

Jan 07, 2011 | 1991 Chevrolet S-10 Blazer

1 Answer

How do you remove and replace a starter for a 1992 2.6L Isuzu Amigo?


1.The battery negative and more importantly positive cable must be disconnected.
2. There are 2 14mm bolts holding the starter in place, the upper bolt can be removed by leaning over into the engine compartment from under the hood with a socket and extension on a ratchet or a ratcheting wrench.
3. crawl under the front passenger wheel and remove the positive cable nut, remove positive cable from starter.
4. unclip the small ground wire attached to starter.
5. remove the lower starter bolt.
6. There is room on the bottom of the vehicle to wiggle the starter down to the floor and out from under the vehicle. There isn't enough room to get the starter out from the engine compartment up and out from under the hood.
7. installation of new starter is reverse of installation.

This procedure should work on any Isuzu Rodeo, Trooper, Amigo, or Honda Passport with a 2.6L 4 cylinder 4ZE1 engine

Nov 12, 2010 | 1992 Isuzu Amigo

1 Answer

What do i have to do to take out the starter in a 1991 s10 with a 4.3 motor i have already taken out both bolts but not enough room


I think this one has the cover on the bottom of the transmission. There will be a couple of support bars that are bolted to it as well. Remove those support bars and the lower cover and you'll have enough room to drop the starter down.

Sep 28, 2010 | 1991 Chevrolet S-10 Blazer

1 Answer

How to install a starter on a 1998 Nissan 200 SX


remove neg battery terminal, next raise car and support, remove wiring to starter then remove mounting bolts to starter . depending on the type of starter the trany may need to be lower a bit to get enough room to remove the starter, try to slide starter out first before lowering trany. hope this helps, reverse to install starter.

Aug 25, 2010 | 1998 Nissan 200SX

1 Answer

How do you remove the wires from the solenoid of a 1995 S-10 chey with a 4.3L w engine? How is the starter removed really.


remove batter cable from batter. follow postive wire down to starter. Should be some "clips" holding wire into place on the waay down to starter. Loosen those clips and take the wire out. Remove wires from stater. Remove two starter bolts. Job is done. By removing the wires out of those clips you give yourself enough slack to easily do this job. If there still isn't enough room for you, it's not suggested but occsaionaly done, once those wires are removed from the clips, remove starter bolts, the starter will hang by the wires while you remove the wires. This can damage the wires and maybe the solenoid on the new starter. That's why it's NOT SUGGESTED.

Jul 21, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

How take the starter off


I had to remove one on a 4x4, if you have 2 wheel drive you have more room. Before you guess the starter is bad, there can be problems with the Main wiring to the starter. There are Corrosion issues on the wiring by the starter.

Some tips I can give you on this for removal. You may need to turn the steering to get clearance and room for wrenches. You need access through the passenger wheelwell with the tire off. You will need socket extensions long enough to reach from the Starter to the Radiator.

When reassembling you will need either a Magnetic retainer for the starter bolt or tape to keep the bolt in the socket. Also you can attach the wires to the Starter before bolting the starter in place. It will may it much easier.

Jul 13, 2010 | 1998 Ford Expedition

1 Answer

I unbloted the starter but there not enough room to pull out the starter


YOU HAVE TO REMOVE SKID PLATE AND DRIVE SHAFT. THE EARLY MODEL YOU HAD TO RAISE THE ENGINE AND TRANSMISSION WITH A FLOOR JACK UNDER THE TRANSMISSION AND REMOVE THE TRANSMISSION CROSSMEMBER FOR ACCESS STARTER MOTOR BOLTS.ALSO REMOVE STARTER HEAT SHIELD.

Jul 08, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

How to remove starter motor on peugeot 307 1.6hdi 2004 model


The hard bit is getting to the starter to unscrew the bolts and getting enough room to remove it once loose. YOu will need to take off a number things from the top of the engine.

The starter is located at the front middle of the engine under the diesel filter.

You will be able get to two of the starter bolts from under the bonnet and the other from below.

You will need to loosen or remove the wiring from around the top of the engine to allow you to remove the starter once loose. (remember where all the plastic connectors reattach).

You should only attempt to do this if you are fairly confident with spanners and have a decent set. You will need 10mm, 11mm, 12mm, 14mm spanners and sockets. 8mm socket, 8mm Allen bolt (straight allen key), small torque.

It is not difficult to do the job just to get to the starter and get enough room to remove and replace. Takes about 4 careful hours start to finish for a none mechanic with car on jacks.

You should always disconnect the battery while removing any electrical/mechanical part from car for safety reasons.

This will help. Thanks please keep updated. please please do rate the solution positively .thank you for using fixya

Mar 18, 2010 | 2005 Peugeot 405

Not finding what you are looking for?
1993 Chevrolet S-10 Blazer Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...