Question about 1997 Chevrolet Blazer

1 Answer

Where r all the bolts for the intake manifold on a 4.3

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,428 Answers

There is olny 8 of then two right next to each other front left side and right side the same in the rearIts not realy not enough and this is why 4.3 have problems with leaking intake gaskets Over heat once thats all it takes TAKE CARE WHEN INSTALLING NEW GASKET clean the surfaces good and use a good quilty sealent in the places the instructoins tell you to good luck

Posted on Nov 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What do the intake manifold bolts for a 2002 Chevy Malibu with a 3.1L need to be torqued to?


Pretend the picture is lower intake manifold, that is the tightening sequence.
1st step 5 ft lbs
2nd step bolts 1--4 9.6 ft lbs
3rd step bolts 5--8 18 ft lbs
The upper intake manifold use about the same sequence tighten to 18 ft lbs.
If you don't like ft lbs use inch lbs.
If the upper intake manifold is plastic, be careful with that.
intake manifold-glquxvjrls3o0ta25lrevmb0-4-0.jpg

Apr 17, 2017 | Chevrolet Malibu Cars & Trucks

1 Answer

Torque setting for a 1998 ford taurus 3.0 intake manifold


TORQUE SPECIFICATIONSDescriptionNmLb-FtLb-InEngine Air Cleaner Tube Clamps1.6-2.2-14-19Engine Control Sensor Wiring Through Bolts2.5-3.5-23-30Generator to Bracket Bolt3727-Generator to Cylinder Head Bolt4835-Generator Brace to Upper Intake Manifold Bolts and Nut12-209-14-Intake Manifold Support to Throttle Body8-12-71-106Intake Manifold Support to RH Cylinder Head40-5530-40-Degas Tube to Upper Intake Manifold Bolts8-12-71-106Camshaft Sprocket to Camshaft Bolt50-7037-51-Camshaft Thrust Plate Bolt10-88Coil and Bracket to Cylinder Head Bolt40-5530-40-Connecting Rod Nut31-3923-28-Crankshaft Damper to Crankshaft Bolt125-16593-121-Crankshaft Pulley to Damper (4 Bolts)40-6030-44-Cylinder Head Retaining Bolt(1)(1)-Accelerator Cable Shield Bolts1.4-13Camshaft Position Sensor Housing Retaining Bolt2417-EGR Tube Connector to Exhaust Manifold40-4730-34-EGR Valve to Upper Intake Manifold Bolt20-3015-22-EGR Tube to EGR Valve and Exhaust Manifold35-6526-47-Exhaust Manifold Bolt/Stud20-2515-18-Flywheel to Crankshaft Bolt73-8754-64-Fuel Injection Supply Manifold to Intake Manifold8-12-71-106Throttle Cable Bracket1713-Dual Converter Y Pipe to Exhaust Manifolds34-4725-34-Crankshaft Position Sensor Bolts5-7-45-61Intake Manifold to Cylinder Head Bolt (5)(2)(2)-Main Bearing Cap Bolt75-8556-62-Oil Drain Plug11-169-11-Oil Filter Insert to Cylinder Block27-4020-29-Oil Filter to Oil Filter Adapter(3)(3)-Oil Galley and Cooling Jacket Plugs2014-Oil Level Indicator Tube to Exhaust Manifold Nut16-2012-14-Engine to Transaxle/Torque Converter Assembly Bolts40-6030-44-Torque Converter Nuts27-4620-33-Transmission Range Sensor Nut16-2212-16-Front Sub-Frame-to-Body Bolts77-10357-75-Oil Pressure Sensor16-2212-16-Oil Pump to Cylinder Block Bolt40-5530-40-Power Steering Bracket to Cylinder Head Bolt40-5530-40-Valve Cover to Cylinder Head Bolts/Studs (5)10-14-89-123Right Exhaust Manifold Heat Shield Retaining Bolts8-12-71-106Rocker Arm Seat to Cylinder Head Bolt(4)(4)-Water Outlet Connection to Intake Manifold Bolt10-14-89-123Upper Intake Manifold to Lower Intake Manifold Bolt/Stud20-3015-22-Engine Front Cover to Cylinder Block Bolt (No. 1-10)2518-Engine Front Cover to Cylinder Block Bolt (No. 11-15)10-88Water Pump Pulley to Hub (4 Bolts)20-3015-22-Water Pump to Front Cover Bolt8-12-71-106Wiring Retainer Bracket Nut20-3015-22-Valve Tappet Guide Plate to Cylinder Block10-14-89-123Ignition Coil Bracket40-5530-40-Oil Pan to Cylinder Block Bolt10-14-89-123Water Bypass Tube Nut20-3015-22-Crankshaft Pulley Bolts40-5530-40-


  1. Tighten in four steps (refer to illustration in Cylinder Head Installation for tightening sequence):
    • Tighten in sequence to 70-90 Nm (52-66 Lb-Ft)
    • Then back off all bolts 360 degrees
    • Tighten in sequence to 45-55 Nm (34-40 Lb-Ft)
    • Tighten in sequence to 85-99 Nm (63-73 Lb-Ft)
  2. Tighten in two steps
    • 20-30 Nm (15-22 Lb-Ft)
    • 26-32 Nm (20-23 Lb-Ft)
  3. Advance 3/4 to 1 turn after gasket contacts sealing surface or tighten to 13-15 Nm (10-11 Lb-Ft).
  4. Tighten in two steps:
    • 7-15 Nm (6-11 Lb-Ft)
    • 26-38 Nm (20-28 Lb-Ft)
  5. Refer to illustration in the Cylinder Head Installation procedure for tightening sequence.

Jan 10, 2012 | 1998 Ford Taurus

1 Answer

Looking for cylinder head torque specs and intake manifold torque specs


on the 2.5 4 cylinder

step 1 18 ft lbs.

step 2 26 ft lbs. except bolt #9 re tighten it to 18 ft. lbs.

step 3 all bolts an additional 90 degrees.

intake manifold bolts 65 ft lbs.

on the 3.3L V6

step 1 35 ft lbs.

step 2 tighten all bolts an additional 130 degrees

step 3 tighten center 4 bolts an additional 30 degrees

intake manifold bolts 88 in. lbs.


Jan 13, 2011 | 1992 Buick Century

1 Answer

How to replace an intake manifold gasket on a 1996 gmc jimmy


Hello,

Here is a detailed summary on the procedure of how to replace the intake manifold gasket on a 1996 gmc jimmy;
REMOVING THE UPPER INTAKE MANIFOLD(PLENUM)
STEP 1 Disconnect Battery (may not be absolutely necessary, but a good practice to avoid shorting a positive wire to ground).


STEP 2 Remove serpentine belt.

STEP 3 Drain the coolant.

STEP 4 Remove air cleaner ducting and disconnect wires.

STEP 5 Disconnect throttle linkage and bracket.

STEP 6 Disconnect cruise control cable.

STEP 7 Remove brake booster vacuum hose at manifold.

STEP 8 Remove PCV hose.

STEP 9 Remove ignition coil and bracket.

STEP 1O Remove purge solenoid and bracket.

STEP 11 Relieve fuel pressure at test port.

STEP 12 Remove fuel lines and bracket.

STEP 13 Remove upper intake manifold.

REMOVING THE LOWER INTAKE MANIFOLD
STEP 1 Remove the distributor and label the spark plug wires.

STEP 2 Remove heater hoses and bypass hose.

STEP 3 Remove upper radiator hose.


STEP 4 Remove EGR valve?

STEP 5 Remove sensors and bracket on right side.

STEP 6 Remove EGR tube, clamp and bolt.

STEP 7 Remove PCV valve (and replace).

STEP 8 Unbolt A/C compressor and move it aside.

STEP 9 Loosen compressor bracket and slide forward, but do not remove it.

STEP 10 Remove alternator bracket bolt (or remove alternator and set aside)

STEP 11 Unplug all vacuum lines from intake manifold.


STEP 12 Unplug all electrical connectors from manifold.

STEP 13 Take note of the intake manifold bolts and mark the location of the bolts.


STEP 14 Remove intake manifold bolts, and manifold.

STEP 15 Clean mating surfaces

THE MAIN INSTALLATION
STEP1 Set the new gaskets in place and apply silicone to flat areas on front and rear of engine block.

STEP2 Apply thread locking compound to manifold bolts.

STEP 3 Install the manifold and tighten bolts to 35 ft-lbs, in proper sequence.

STEP4 Install the distributor.

STEP5 Install the upper intake manifold.



The remaining installation procedures are basically the reverse of removal.


Have a nice day.

Dec 04, 2010 | 1996 GMC Jimmy

1 Answer

2001 chrysler voyager just replaced head what are the torque specs for head intake and pivot arm


for the head

Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.)

† Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.)

† Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.)

† Step 4: Bolts 1 - 8 turn an additional 1/4 Turn.

(Do not use a torque wrench for this step.)

NOTE: Bolt torque after 1/4 turn should be over 122
N·m (90 ft. lbs.). If not, replace the bolt.


Intake Manifold

Bolts . . . . . . . . . . . . . . . . . . . .23 N·m (200 in. lbs.)

Intake Manifold Gasket Retaining

Screws . . . . . . . . . . . . . . . . . .12 N·m (105 in. lbs.)

Intake Manifold Plenum
Bolts . . . . . . . . . . . . . . . . . . . .28 N·m (250 in. lbs.)
the pivot arm ? whats that

Nov 13, 2010 | 2001 Chrysler Voyager

1 Answer

Diagram on how to remove and install a spider fuel injector core on a 1994 chevy blazer s10


Here is the removal procedure, and the procedure is the same for both the V-6 and the V-8 Vortec engines. Also, be certain to put engine oil on the "o"-ring seal for the fuel injector assembly before installing the upper intake. Let me know if you require any further assistance.

REMOVAL:

1. Disconnect the battery negative cable assembly from the battery negative terminal.

2. Remove the air cleaner assembly.

3. Remove the wiring harness connectors and the brackets and move aside.

4. Remove the throttle cable and the bracket from the upper intake manifold.

5. Remove the cruise control cable, (if equipped).

6. Remove the fuel lines from the intake to the rear of the block.

7. Remove the ignition coil and the bracket.

8. Remove the upper intake manifold.

INSTALLATION:

1. Install the upper intake manifold gasket.

2. Install the upper intake manifold. Use care not to pinch the injector lines between the upper and lower intake manifolds.

3. Install the upper intake manifold bolts. Note the marks made at disassembly for proper stud location. Install the two corner studs first in order to help align the two halves. NOTE: Other than the two torque passes listed below, the OE Manufacturer did NOT address or supply a bolt tightening sequence for the upper Intake Manifold for this model year, or other model years where this 2 piece manifold setup is used. A "Play It Safe" final tightening sequence would be to tighten from the center most bolts to the outer most bolts.

4. Tighten the bolts in two steps: a. Tighten the bolts on the first sequence to 5 Nm (44 inch lbs.). b. Tighten the bolts on the final sequence to 10 Nm (88 inch lbs.).

5. Install the purge solenoid and bracket.

6. Install the ignition coil and bracket.

7. Install the PCV hose et the upper intake manifold.

8. Install the fuel lines from the intake at the rear of the block.

9. Install the cruise control cable (if equipped).

10. Install the throttle cable and bracket from the upper intake manifold.

11. Install the wiring harness connectors and brackets.

12. Install the air cleaner assembly.

13. Connect the battery negative cable assembly to the battery negative terminal. - Tighten the bolt to 15 Nm (11 ft. lbs.).


2640099.jpg

8a054ef.jpg

Oct 22, 2010 | Chevrolet Blazer Cars & Trucks

2 Answers

Need to replace the intake manifold


3.8L Engine (most common) Upper Intake Manifold To Remove:
  1. Drain the cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable.
    • Fuel injector sight shield.
    • Air cleaner intake duct.
    • Right spark plug wires from the ignition control module and reposition.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Fuel rail assembly.
    • Brake booster hose from the vacuum source manifold in the upper intake manifold.
    • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
    • Throttle body support bracket upper bolt.
  5. Disconnect the electrical connectors from the following:
    • EVAP purge solenoid
    • Throttle Position (T/P) sensor
    • Idle Air Control (IAC) valve
    • Manifold Absolute Pressure (MAP) sensor
    • Mass Air Flow (MAF) sensor
    • EVAP purge solenoid vacuum line from the throttle body.
    • Accelerator and the cruise control cables with the bracket from the throttle body.
  6. Remove or disconnect the following:
    • Upper intake manifold bolts and stud.
    • Clean the upper intake manifold bolt threads.
  7. Remove or disconnect the following:
    • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
    • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
  8. If the upper intake manifold is being replaced, remove the following:
    • Throttle body assembly.
    • Manifold Absolute Pressure (MAP) sensor.
    • Positive Crankcase Ventilation (PCV) valve.
    • Vacuum source manifold.
Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

To Install:
  1. If the manifold was replaced, install or connect the following:
    • Vacuum source manifold.
    • Positive Crankcase Ventilation (PCV) valve.
    • Manifold Absolute Pressure (MAP) sensor.
    • Throttle body assembly.
    • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
  2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
  3. Install or connect the following:
    • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
    • Accelerator and the cruise control cables with the bracket to the throttle body.
    • EVAP purge solenoid vacuum line to the throttle body.
  4. Connect the electrical connectors to the following:
    • Mass Air Flow (MAF) sensor
    • Manifold Absolute Pressure (MAP) sensor
    • Idle Air Control (IAC) valve
    • Throttle Position (T/P) sensor
    • EVAP purge solenoid
  5. Install or connect the following:
    • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
    • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
    • Brake booster hose to the vacuum source manifold.
    • Fuel rail assembly.
    • Right spark plug wires.
    • Air cleaner intake duct.
    • Fuel injector sight shield.
  6. Connect the negative battery cable.
  7. Fill the cooling system.
  8. Inspect for fluid or vacuum leaks.
Lower Intake Manifold (W/O Supercharger) To Remove:
  1. Remove or disconnect the following:
    • Upper intake manifold.
    • Generator brace.
    • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
    • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
    • Radiator inlet hose from the water outlet housing.
    • ECT sensor electrical connector.
    • Right upper engine mount strut bracket.
    • Generator brace bracket bolts.
    • Generator brace bracket.
    • Lower intake manifold bolts.
    • Lower intake manifold.
    • Lower intake manifold seals.
    • Lower intake manifold gaskets.
  2. If replacing the lower intake manifold, Remove or disconnect:
    • Water outlet housing bolt and stud
    • Water outlet housing
    • Gasket and the thermostat.
    • ECT sensor.
  3. Inspect the flatness of inlet flanges.
  4. Clean the intake manifold mating surfaces.
  5. Clean the intake manifold bolts and bolt holes of adhesive compound.
To Install:
  1. If removed, install the ECT sensor.
    • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
  2. If removed, install the thermostat, the gasket, and the water outlet housing.
  3. If removed, install the water outlet housing bolt and the stud.
    • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
  4. Install or connect the following:
    • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
    • Lower intake manifold seals.
    • Lower intake manifold.
    • Lower intake manifold bolts.
    NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
  5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

  6. Install or connect the following:
    • Generator brace bracket.
    • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
    • Right upper engine mount strut bracket.
    • ECT sensor electrical connector.
    • Radiator inlet hose to the water outlet housing.
    • EGR outlet pipe to the lower intake manifold.
    • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
    • Drive belt tensioner.
    • Generator brace.
    • Upper intake manifold.
  7. Inspect for leaks.
Lower Intake Manifold (W/ Supercharger) To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the supercharger.
  4. Remove the thermostat housing.
  5. Remove the EGR pipe at the intake manifold.
  6. Disconnect the electrical connection at the temperature sensor.
  7. Remove the intake manifold and gaskets.
NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:
  1. Clean the gasket sealing surfaces.
  2. Install the intake manifold gaskets.
  3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
  4. Install the electrical connector to the temperature sensor.
  5. Install the EGR pipe to the intake manifold.
  6. Install the thermostat housing.
  7. Install the supercharger.
  8. Fill the cooling system.
  9. Connect the negative battery cable.

Aug 05, 2010 | 1997 Pontiac Grand Prix

1 Answer

What is the torque settings on the head bolts for 2002 nissan x-terra 2.4litre?


① Step 1: 22 ft. lbs. Step 2: 59 ft. lbs. Step 3: Loosen completely then retorque to 22 ft. lbs. Step 4: 18-25 ft. lbs. Step 5: Plus 86-91 degrees ② 10-12 ft. lbs. plus 60-65 degrees or 28-33 ft. lbs. ③ The cylinder heads and the lower intake manifold are installed together Step 1: Tighten the cylinder head bolts to 22 ft. lbs. Step 2: Tighten the cylinder head bolts to 43 ft. lbs. Step 3: Loosen the cylinder head bolts completely Step 4: Tighten the cylinder head bolts to 84 inch lbs. Step 5: Tighten the intake manifold fasteners to 35 inch lbs. Step 6: Tighten the intake manifold fasteners to 13 ft. lbs. Step 7: Tighten the intake manifold fasteners to 12-14 ft. lbs. Step 8: Loosen all intake manifold fasteners completely Step 9: Tighten the cylinder head bolts to 22 ft. lbs. Step 10: Tighten the cylinder head bolts 60-65 degrees Step 11: Tighten the cylinder head sub-bolts to 80-105 inch lbs. Step 12: Tighten the intake manifold fasteners to 35 inch lbs. Step 13: Tighten the intake manifold fasteners to 78 inch lbs. Step 14: Tighten the intake manifold fasteners to 70-84 inch lbs. ④ 10-12 ft. lbs. +60-65 degrees ⑤ Step 1: 72 ft. lbs. Step 2: loosen completely to 0 ft. lbs. Step 3: 29 ft. lbs. Step 4: Plus 75 degrees clockwise Step 5: Plus 75 degrees clockwise ⑥ Step 1: bolts 11-22 19 ft. lbs. Step 2: bolts 1-10 29 ft. lbs. Step 3: bolts 1-10 Plus 60-65 degrees ⑦ Step 1: 20 ft. lbs. Step 2: loosen to 0 ft. lbs. Step 3: 14 ft. lbs. Step 4: Plus 85-95 degrees ⑧ Step 1: 31 ft. lbs. Step 2: Plus 60 degrees ⑨ 83 inch lbs. ⑩ Stud bolt: 11 ft. lbs. Nuts: 31 ft. lbs. ⑪ Step 1: 72 ft. lbs. Step 2: loosen completely to 0 ft. lbs. Step 3: 29 ft. lbs. Step 4: Plus 90 degrees clockwise Step 5: Plus 90 degrees clockwise ⑫ Bolts: 17-24 (M8) 16 ft. lbs. Install rear main seal Bolts: 1-16 (M10) 26 ft. lbs. Bolts: 1-16 (M10) Plus 90 degrees clockwise ⑬ Step 1: 33 ft. lbs. Step 2: Plus 84-90 degrees clockwise ⑭ Intake manifold collector: Bolts and nuts: 8 ft. lbs. Stud bolts: 61 inch lbs. ⑮ Intake manifold: Bolts and nuts: 5 ft. lbs. and than to 21 ft. lbs. Studs: 8 ft. lbs.

Jan 10, 2010 | 2002 Nissan Xterra

1 Answer

Starter for kia sportage 2000


  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Intake manifold bracket upper bolts Clutch release cylinder and move it aside, if equipped Intake manifold bracket lower bolts and remove the bracket Starter from the clutch, manual transmissions only Starter from the torque converter, automatic transmissions only Starter electrical connectors Move the transmission wire harness aside Starter


    0900c152801b0603.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the starter

To install:
  1. Install or connect the following:

    Starter to the engine well Starter electrical connectors Lower intake manifold bracket and install the upper bolts Starter into position. When aligned properly torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket bolts to 40 ft. lbs. (54 Nm). Properly position the clutch release cylinder, if equipped. Torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket upper bolts to 40 ft. lbs. (54 Nm). Negative battery cable

Jun 28, 2009 | 2000 Kia Sportage

1 Answer

I need a diagram of a 1995 ford escort engine


96 escort 1.9L

bb97132.gif
e0d7524.gif

Engine Components
Item Part Number Description 1 6766 Oil Filler Cap 2 6A548 (8 Req'd) Valve Cover Bolt 3 6582 Valve Cover 4 — Exhaust Manifold Shield-to-Exhaust Manifold Nut (4 Req'd) 5 9A462 Exhaust Manifold Shield 6 — Exhaust Manifold Shield Stud (4 Req'd) 7 9430 Exhaust Manifold 8 9454 Exhaust Manifold Nut 9 9448 Exhaust Manifold Gasket 10 — Exhaust Manifold Stud (Fine Thread), Short (4 Req'd) 11 — Exhaust Manifold Stud, Long (1 Req'd) 12 — Exhaust Manifold Stud (Medium Thread), Short (1 Req'd) 13 6518 Valve Spring Retainer Key 14 6514 Valve Spring Retainer 15 6513 Valve Spring and Damper, Intake 16 6C515 Valve Tappet Guide Plate Retainer 17 6571 Valve Stem Seal 18 6513 Valve Spring, Exhaust 19 12405 Spark Plug 20 6269 Camshaft Thrust Plate 21 — Camshaft Thrust Plate Bolt (2 Req'd) 22 — Cup Plug 23 6B273 Camshaft Oil Flow Control Rod 24 6K292 Camshaft Front Seal 25 6256 Camshaft Sprocket 26 6278 Camshaft Sprocket Washer 27 6K252 Camshaft Sprocket Retaining Bolt 28 6L269 Camshaft Sprocket Key (5 x 18) 29 6250 Camshaft 30 6051 Head Gasket 31 6A008 Cylinder Head to Block Dowel 32 6010 Cylinder Block 33 6507 Intake Valve 34 6505 Exhaust Valve 35 6049 Cylinder Head 36 — Intake Manifold Stud (7 Req'd) 37 17A084 Engine Lifting Eye 38 — Engine Lifting Eye Bolt (2 Req'd) 39 9439 Intake Manifold Gasket 40 — Bolt 41 9723 Accelerator Cable Bracket 42 9424 Intake Manifold 43 — Intake Manifold Nut (7 Req'd) 44 9D476 EGR Valve Gasket 45 — Exhaust Gas Recirculation (EGR) Valve Bolt (2 Req'd) 46 9D475 EGR Valve 47 — Fuel Injection Supply Manifold Bolt
(2 Req'd) 48 9F593 Fuel Injector 49 9D930 Fuel Charging Wiring 50 6786 Oil Level Indicator Tube Bracket 51 — Oil Level Indicator Tube Bracket Bolt 52 6754 Oil Level Indicator Tube 53 6750 Oil Level Dipstick 54 9D280 Fuel Injection Supply Manifold 55 — Vacuum Fitting 56 9E498 Main Emission Vacuum Control Connector 57 — Vacuum Tap 58 — Vacuum Hose 59 9B989 Throttle Position Sensor 60 — Screw and Washer 61 9F782 Throttle Position Sensor Gasket 62 — Throttle Body Bolt (4 Req'd) 63 — Idle Air Control (IAC) Valve Bolt
(2 Req'd) 64 9F715 Idle Air Control Valve 65 9F670 Idle Air Control Gasket 66 9E926 Throttle Body 67 9E936 Throttle Body Gasket 68 — Vacuum Fitting 69 — Camshaft Position Sensor Screw 70 6B288 Camshaft Position Sensor 71 8255 Water Hose Connection Gasket 72 — Water Hose Connection Bolt (3 Req'd) 73 8592 Water Hose Connection 74 8575 Water Thermostat 75 6065 Cylinder Head Bolts 76 6500 Valve Tappet 77 6K512 Valve Tappet Guide Plate 78 6564 Rocker Arm 79 6A528 Rocker Arm Seat 80 6A527 Rocker Arm Bolt (8 Req'd) 81 — Ignition Coil Mounting Bracket Bolt
(3 Req'd) 82 18827 Noise Filter Condenser 83 — Ignition Coil Mounting Bolt (4 Req'd) 84 12259 Spark Plug Wire Set 85 12029 Ignition Coil 86 12043 Ignition Coil Mounting Bracket A — Tighten to 5-12 Nm (4-9 Lb-Ft) B — Tighten to 5-7 Nm (3-5 Lb-Ft) C — Tighten to 21-26 Nm (16-19 Lb-Ft) D — Tighten to 2-10 Nm (1.5-7 Lb-Ft) E — Tighten to 8-13 Nm (6-9 Lb-Ft) F — Tighten to 40-55 Nm (30-41 Lb-Ft) G — Tighten to 16-20 Nm (12-15 Lb-Ft) H — Tighten to 20-30 Nm (15-22 Lb-Ft) I — Tighten to 8-10 Nm (6-8 Lb-Ft) J — Tighten to 8-11 Nm (6-9 Lb-Ft) K — Tighten to 23-30 Nm (17-22 Lb-Ft) L — Tighten to 20-40 Nm (15-30 Lb-Ft) M — Tighten to 4.5-7 Nm (3-5 Lb-Ft) N — Tighten to 18-26 Nm (13-19 Lb-Ft)

Feb 24, 2009 | 1995 Ford Escort

Not finding what you are looking for?
1997 Chevrolet Blazer Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...