Question about Ford Bronco

Open Question

Firing order ford industrial 6 cyl 300 - Bronco Ford Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: firing order for 1998 ford explorer 6 cyl

1-4-2-5-3-6

Posted on Mar 22, 2009

  • 6982 Answers

SOURCE: firing order for 1997 jeep cherokee straight 6 cyl.

153624 On cap #1 is two towers clockwise from right side hold-down screw, #1 is front cyl on engine. Firing order is clockwise.

Posted on Apr 15, 2009

motor1258
  • 6674 Answers

SOURCE: 93 ford f150 300 6 need firing order if ur looking

4.9L engine. firing order 1,5,3,6,2,4. clockwise rotation.c978c76.gif

Posted on Aug 04, 2009

mindreader
  • 578 Answers

SOURCE: i need the torque specs for a ford 300 inline 6

Tighten all bolts to 10 Lbs, then 20 Lbs, then 35 Lbs.
That should be fine for the 6 cylinder flywheel.

Posted on Oct 10, 2009

  • 834 Answers

SOURCE: 1966 ford f100 inline 6 cyl 300\r\engine turns

Make sure that the primary wire between the distributor ignition points and ignition coil is not damaged anywhere and grounding the circuit out. This is not a ground wire.

Replace the ignition points condenser, if this is shorted your points will never be able to work. With the condenser removed, use an ohm meter to check the resistance between the end of the condenser wire and the condenser caseing, there should be infinite resistance or an open loop, but it should not show any kind of a connection between the two, or it is grounded or "shorted to ground" and it will prevent the ignition system from working.

Are the ignition points adjusted properly? They have to open and close to send a dwell signal to the coil.

Connect a test light to ground and on the NEG. (-) side of the coil, have someone crank the engine and look for the test light to flash, the test light should flash indicating a dwell signal or coil pulse. (Do not use the POS. + side of the coil for this test, because you will not get a dwell signal).

If no dwell signal, then...

1. Turn off ignition and remove the distributor cap and turn the engine over until a high spot on the distributor cam lobe is on the rubbing block on the ignition points.

This is the fully open position for the ignition points and where they need to be to set them. and if you do not know the feeler gauge size, or the dwell angle to set your points at (according to manufacturers specifications), then tear off a piece of a match book and place it between the two point breakers.

2. Loosen the point hold down adjusting screw and move the base of the points with a screwdriver (look for adjusting nothches), until there is a light drag felt pulling on the match book. For the newer GM's up to 1974, just use a 1/8 allen wrench to obtain the same light drag on the match book.

3. Remove the matchbook and there should still be a small gap between the point breakers, rotate the engine and you should see the points open and fully close.

4. Pull the coil wire out of the distributor cap and ground the end of the coil wire well or you might get shocked.

5. Have someone crank the engine and re-check for a dwell signal, you should also see a blue-white spark flashing between the point breakers as they open and close.

If you now have a dwell signal then replace the distributor cap back onto the distributor and the the coil wire back onto the distributor cap, the engine should now start.

If you did not grease the rubbing block of the ignition points with die-electric grease when you installed them, then the rubbing block on the points will wear down prematurely, the points will close down, and the engine will no longer start.

If you crank your engine over and the ignition rotor turns clockwise (looking down at the rotor) then you need to put the die-electric grease along the right side of the rubbing block edge (looking down at the points) so that the grease is trapped between the points and the distributor cam lobe, and the distributor cam lobe can pick up the grease. (Grease the left side of the rubbing block edge if the ignition rotor turns counter-clockwise). Only use die-electric grease.

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford ranger 1999 firing order


For the 4 cyl it's 1-3-4-2. the 3.0 6cyl. it's 1-4-2-5-3-6, the 4.0 6 cyl. it's 1-4-2-5-3-6.

Apr 13, 2014 | Ford Ranger Cars & Trucks

1 Answer

Need firing order diagram for 1995 f-150 6-cyl 4.9 litre


1-5-3-6-2-4 is the spark plug firing order for the 4.9 L ( 300 cubic inch ) straight 6

The distributor rotor turns CLOCKWISE

The marked # 1 position on the distributor cap is installed facing away from the engine


Hope this helps

Jun 08, 2011 | Ford F-150 Cars & Trucks

2 Answers

2001 ford taurus lx firing order diagram


Here is a diagram. Firing order 1-4-2-5-6-3


emissionwiz_95.gif

May 20, 2011 | Ford Taurus Cars & Trucks

2 Answers

2000 ford mustang code 453 and missfire cyl 5 where is the cyl


a haynes manual from a parts place will show you--or chec the condition of each plug wire-if one looks bad or falls apart--probly need to get all new wires /plugs

Dec 18, 2010 | 2000 Ford Mustang

1 Answer

Firing order ford 300 six and #1 position on distributer cap 1990


THE 300 4.9 ENGINE FIRING ORDER IS 1 5 3 6 2 4 THE NUMBER 1 POSITION ON DISTRIBUTOR CAP IS AT 6 OCLOCK POSITION.

Jul 13, 2010 | 1990 Ford F250

2 Answers

I mixed up my firing order on my ford F-150 300 engine i need the correct firing order.


For the Ford 300 inline 6 cylinder the firing order is: 1-5-3-6-2-4

Hope this helps

Jun 26, 2010 | Cars & Trucks

1 Answer

Firing order for 1996 ford explorer


You didn't tell me if you have a 6 cyl, 8 cyl or 4WD, so i'll give you a link where you can check the engine you have. Scroll down the page to Explorer and click on the engine you have...

http://autorepair.about.com/library/firing_orders/bl-ford-firing-96.htm

Oct 06, 2009 | 1996 Ford Explorer

1 Answer

Ford 300


if its a strait 6 its 1 5 3 6 2 4 thats for a 300 six cyl

Jun 05, 2008 | 1981 Ford F 150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...